1 ANNEX, Decision_act (EU) 2013/163

In forcesince 26 Mar 2013

These BAT conclusions concern the following industrial activities specified in Section 3.1 of Annex I to Directive 2010/75/EU, namely:

'3.1. Production of cement, lime and magnesium oxide', which involve:

(a)

production of cement clinker in rotary kilns with a production capacity exceeding 500 tonnes per day or in other kilns with a production capacity exceeding 50 tonnes per day;

(b)

production of lime in kilns with a production capacity exceeding 50 tonnes per day;

(c)

production of magnesium oxide in kilns with a production capacity exceeding 50 tonnes per day.

Regarding point 3.1(c) above, these BAT conclusions only address the production of MgO using the dry process route based on mined natural magnesite (magnesium carbonate - MgCO3).

In particular, concerning the above-mentioned activities, these BAT conclusions cover the following:

production of cement, lime and magnesium oxide (dry process route)

raw materials – storage and preparation

fuels – storage and preparation

use of waste as raw materials and/or fuels – quality requirements, control and preparation

products – storage and preparation

packaging and dispatch.

These BAT conclusions do not address the following activities:

the production of magnesium oxide using the wet process route using magnesium chloride as the starting material, covered by the Reference Document on Best Available Techniques for Large Volume Inorganic Chemicals – Solids and Others Industry (LVIC-S)

the production of ultra low-carbon dolime (i.e. a mixture of calcium and magnesium oxides produced by the nearly full decarbonation of dolomite (CaCO3.MgCO3). The residual CO2 content of the product is below 0,25 % and the bulk density well below 3,05 g/cm3)

shaft kilns for cement clinker production

activities which are not directly associated with the primary activity such as quarrying.

Other reference documents which are of relevance for the activities covered by these BAT conclusions are the following:

Reference documents | Activity

Emissions from Storage (EFS) | Storage and handling of raw materials and products

General Principles of Monitoring (MON) | Emissions monitoring

Waste Treatments Industries (WT) | Waste treatment

Energy Efficiency (ENE) | General energy efficiency

Economic and Cross-media Effects (ECM) | Economics and cross-media effects of techniques

The techniques listed and described in these BAT conclusions are neither prescriptive nor exhaustive. Other techniques may be used that ensure at least an equivalent level of environmental protection.

Where these BAT conclusions address waste co-incineration plants, this is without prejudice to the provisions of Chapter IV of and Annex VI to Directive 2010/75/EU.

Where these BAT conclusions address energy efficiency, this is without prejudice to the provisions of the new Directive 2012/27/EU of the European Parliament and of the Council [OJ L 315, 14.11.2012, p. 1.] on Energy Efficiency.

The exchange of information on BAT for the Cement, Lime and Magnesium Oxide sectors ended in 2008. The information available then, complemented by additional information concerning the emissions from magnesium oxide production, was used for reaching these BAT conclusions.

For the purposes of these BAT conclusions, the following definitions apply:

Term used | Definition

New plant | A plant introduced on the site of the installation following the publication of these BAT conclusions or a complete replacement of a plant on the existing foundations of the installation following the publication of these BAT conclusions

Existing plant | A plant which is not a new plant

Major upgrade | An upgrade of the plant/kiln involving a major change in the kiln requirements or technology, or replacement of the kiln

'Use of waste as fuel and/or raw material' |

The term covers the use of:

waste fuels with significant calorific value; and

waste materials without significant calorific value but with mineral components used as raw materials that contribute to the intermediate product clinker; and

waste materials that have both a significant calorific value and mineral components

Term used | Definition

White cement | Cement falling under the following PRODCOM 2007 code: 26.51.12.10 – White Portland cement

Special cement |

Special cements falling under the following PRODCOM 2007 codes:

26.51.12.50 – Aluminous cement

26.51.12.90 – Other hydraulic cements

Dolime or calcinated dolime | A mixture of calcium and magnesium oxides produced by the decarbonation of dolomite (CaCO3.MgCO3) with a residual CO2 content of the product exceeding 0,25 % and the bulk density of the commercial product well below 3,05 g/cm3. The free content as MgO is usually between 25 % and 40 %.

Sintered dolime | A mixture of calcium and magnesium oxides used solely for the production of refractory bricks and other refractory products, with a minimum bulk density of 3,05 g/cm3

Term used | Definition

NOx expressed as NO2 | The sum of nitrogen oxide (NO) and nitrogen dioxide (NO2) expressed as NO2

SOx expressed as SO2 | The sum of sulphur dioxide (SO2) and sulphur trioxide (SO3) expressed as SO2

Hydrogen chloride expressed as HCl | All gaseous chlorides expressed as HCl

Hydrogen fluoride expressed as HF | All gaseous fluorides expressed as HF

ASK | Annular shaft kiln

DBM | Dead burned magnesia

I-TEQ | International toxicity equivalent

LRK | Long rotary kiln

MFSK | Mixed feed shaft kiln

OK |

Other kilns

For the lime industry this covers:

double-inclined shaft kilns

multi-chamber shaft kilns

central burner shaft kilns

external chamber shaft kilns

beam burner shaft kilns

internal arch shaft kilns

travelling grate kilns

‘top-shaped’ kilns

flash calciner kilns

rotating hearth kilns

OSK | Other shaft kiln (shaft kilns other than ASK and MFSK)

PCDD | Polychlorinated dibenzo-p-dioxin

PCDF | Polychlorinated dibenzofuran

PFRK | Parallel flow regenerative kiln

PRK | Rotary kiln with preheater

Emission levels associated with the best available techniques (BAT-AELs) given in these BAT conclusions refer to standard conditions: dry gas at a temperature of 273 K, and a pressure of 1013 hPa.

Values given in concentrations apply under the following reference conditions:

[For sintered dolime produced by the 'double-pass process', the correction for oxygen does not apply.] [For dead burned magnesia (DBM) produced by the 'double-pass process', the correction for oxygen does not apply.]

Activities | Reference conditions

Kiln activities | Cement industry | 10 % oxygen by volume

Lime industry | 11 % oxygen by volume

Magnesium oxide industry (dry process route) | 10 % oxygen by volume

Non-kiln activities | All processes | No correction for oxygen

Lime hydrating plants |

As emitted

(no correction for oxygen and for dry gas)

For averaging periods the following definitions apply:

Daily average value | Average value over a period of 24 hours measured by the continuous monitoring of emissions

Average over the sampling period | Average value of spot measurements (periodic) of at least 30 minutes each, unless otherwise stated

The formula for calculating the emissions concentration at a reference oxygen level is shown below:

ER = 21 – OR21 – OM * EM

Where:

ER (mg/Nm3)emissions concentration related to the reference oxygen level OR

OR (vol %)reference oxygen level

EM (mg/Nm3)emissions concentration related to the measured oxygen level OM

OM (vol %)measured oxygen level

The BAT mentioned in this section apply to all installations covered by these BAT conclusions (cement, lime and magnesium oxide industry).

The process-specific BAT included in Sections 1.2 - 1.4 apply in addition to the general BAT mentioned in this section.

1.

In order to improve the overall environmental performance of the plants/installations producing cement, lime and magnesium oxide, production BAT is to implement and adhere to an environmental management system (EMS) that incorporates all of the following features:

i.

commitment of the management, including senior management;

ii.

definition of an environmental policy that includes the continuous improvement of the installation by the management;

iii. planning and establishing the necessary procedures, objectives and targets, in conjunction with financial planning and investment;

iv. implementation of procedures paying particular attention to:

(a)

structure and responsibility

(b)

training, awareness and competence

(c)

communication

(d)

employee involvement

(e)

documentation

(f)

efficient process control

(g)

maintenance programmes

(h)

emergency preparedness and response

(i)

safeguarding compliance with environmental legislation;

v.

checking performance and taking corrective action, paying particular attention to:

(a)

monitoring and measurement (see also the Reference Document on the General Principles of Monitoring)

(b)

corrective and preventive action

(c)

maintenance of records

(d)

independent (where practicable) internal and external auditing in order to determine whether or not the EMS conforms to planned arrangements and has been properly implemented and maintained;

vi. review of the EMS and its continuing suitability, adequacy and effectiveness by senior management;

vii. following the development of cleaner technologies;

viii. consideration for the environmental impacts from the eventual decommissioning of the installation at the stage of designing a new plant, and throughout its operating life;

ix. application of sectoral benchmarking on a regular basis.

The scope (e.g. level of details) and nature of the EMS (e.g. standardised or non-standardised) will generally be related to the nature, scale and complexity of the installation, and the range of environmental impacts it may have.

2.

In order to reduce/minimise noise emissions during the manufacturing processes for cement, lime and magnesium oxide, BAT is to use a combination of the following techniques:

Technique

a | Select an appropriate location for noisy operations

b | Enclose noisy operations/units

c | Use vibration insulation of operations/units

d | Use internal and external lining made of impact-absorbent material

e | Use soundproofed buildings to shelter any noisy operations involving material transformation equipment

f | Use noise protection walls and/or natural noise barriers

g | Use outlet silencers to exhaust stacks

h | Lag ducts and final blowers which are situated in soundproofed buildings

i | Close doors and windows of covered areas

j | Use sound insulation of machine buildings

k | Use sound insulation of wall breaks, e.g. by installation of a sluice at the entrance point of a belt conveyor

l | Install sound absorbers at air outlets, e.g. the clean gas outlet of dedusting units

m | Reduce flow rates in ducts

n | Use sound insulation of ducts

o | Apply the decoupled arrangement of noise sources and potentially resonant components, e.g. of compressors and ducts

p | Use silencers for filter fans

q | Use soundproofed modules for technical devices (e.g. compressors)

r | Use rubber shields for mills (avoiding the contact of metal against metal)

s | Construct buildings or growing trees and bushes between the protected area and the noisy activity

Unless otherwise stated, the BAT conclusions presented in this section can be applied to all installations in the cement industry.

3.

In order to reduce emissions from the kiln and use energy efficiently, BAT is to achieve a smooth and stable kiln process, operating close to the process parameter set points by using the following techniques:

Technique

a | Process control optimisation, including computer-based automatic control

b | Using modern, gravimetric solid fuel feed systems

4.

In order to prevent and/or reduce emissions, BAT is to carry out a careful selection and control of all substances entering the kiln.

Careful selection and control of substances entering the kiln can reduce emissions. The chemical composition of the substances and the way they are fed in the kiln are factors that should be taken into account during the selection. Substances of concern may include the substances mentioned in BAT 11 and in BAT 24 to 28.

5.

BAT is to carry out the monitoring and measurements of process parameters and emissions on a regular basis and to monitor emissions in accordance with the relevant EN standards or, if EN standards are not available, ISO, national or other international standards that ensure the provision of data of an equivalent scientific quality, including the following:

Technique | Applicability

a | Continuous measurements of process parameters demonstrating the process stability, such as temperature, O2 content, pressure and flowrate | Generally applicable

b | Monitoring and stabilising critical process parameters, i.e. homogenous raw material mix and fuel feed, regular dosage and excess oxygen | Generally applicable

c | Continuous measurements of NH3 emissions when SNCR is applied | Generally applicable

d | Continuous measurements of dust, NOx, SOx, and CO emissions | Applicable to kiln processes

e | Periodic measurements of PCDD/F and metal emissions

f | Continuous or periodic measurements of HCl, HF and TOC emissions.

g | Continuous or periodic measurements of dust |

Applicable to non-kiln activities.

For small sources (< 10000 Nm3/h) from dusty operations other than cooling and the main milling processes, the frequency of measurements or performance checks should be based on a maintenance management system.

The selection between continuous or periodic measurements mentioned in BAT 5(f) is based on the emission source and the type of pollutant expected.

6.

In order to reduce energy consumption, BAT is to use a dry process kiln with multistage preheating and precalcination.

In this type of kiln system, exhaust gases and recovered waste heat from the cooler can be used to preheat and precalcine the raw material feed before entering the kiln, providing significant savings in energy consumption.

Applicable to new plants and major upgrades, subject to raw materials moisture content.

See Table 1.

[Levels do not apply to plants producing special cement or white cement clinker that require significantly higher process temperatures due to product specifications.] [Under normal (excluding, e.g. start-ups and shutdowns) and optimised operational conditions.] [The production capacity has an influence on the energy demand, with higher capacities providing energy savings and smaller capacities requiring more energy. Energy consumption also depends on the number of cyclone preheater stages, with more cyclone preheater stages leading to lower energy consumption of the kiln process. The appropriate number of cyclone preheater stages is mainly determined by the moisture content of raw materials.]

Process | Unit | BAT-associated energy consumption levels

Dry process with multistage preheating and precalcination | MJ/tonne clinker | 2900 – 3300

7.

In order to reduce/minimise thermal energy consumption, BAT is to use a combination of the following techniques:

Technique | Applicability

a |

Applying improved and optimised kiln systems and a smooth and stable kiln process, operating close to the process parameter set points by applying:

I.

process control optimisation, including computer-based automatic control systems

II.

modern, gravimetric solid fuel feed systems

III.

preheating and precalcination to the extent possible, considering the existing kiln system configuration

Generally applicable. For existing kilns, the applicability of preheating and precalcination is subject to the kiln system configuration

b | Recovering excess heat from kilns, especially from their cooling zone. In particular, the kiln excess heat from the cooling zone (hot air) or from the preheater can be used for drying raw materials |

Generally applicable in the cement industry.

Recovery of excess heat from the cooling zone is applicable when grate coolers are used.

Limited recovery efficiency can be achieved on rotary coolers

c | Applying the appropriate number of cyclone stages related to the characteristics and properties of raw material and fuels used | Cyclone preheater stages are applicable to new plants and major upgrades.

d | Using fuels with characteristics which have a positive influence on the thermal energy consumption | The technique is generally applicable to the cement kilns subject to fuel availability and for existing kilns subject to the technical possibilities of injecting the fuel into the kiln

e | When replacing conventional fuels by waste fuels, using optimised and suitable cement kiln systems for burning wastes | Generally applicable to all cement kiln types

f | Minimising bypass flows | Generally applicable to the cement industry

Several factors affect the energy consumption of modern kiln systems such as raw materials properties (e.g. moisture content, burnability), the use of fuels, with different properties, as well as the use of a gas bypass system. Furthermore, the production capacity of the kiln has an influence on the energy demand.

Technique 7c: the appropriate number of cyclone stages for preheating is determined by the throughput and the moisture content of raw materials and fuels which have to be dried by the remaining flue-gas heat because local raw materials vary widely regarding their moisture content or burnability

Technique 7d: conventional and waste fuels can be used in the cement industry. The characteristics of the fuels used, such as adequate calorific value and low moisture content, have a positive influence on the specific energy consumption of the kiln.

Technique 7f: the removal of hot raw material and hot gas leads to a higher specific energy consumption of about 6 – 12 MJ/tonne clinker per percentage point of removed kiln inlet gas. Hence, minimising the use of gas bypass has a positive effect on energy consumption.

8.

In order to reduce primary energy consumption, BAT is to consider the reduction of the clinker content of cement and cement products.

The reduction of the clinker content of cement and cement products can be achieved by adding fillers and/or additions, such as blast furnace slag, limestone, fly ash and pozzolana in the grinding step in accordance with the relevant cement standards.

Generally applicable to the cement industry, subject to (local) availability of fillers and/or additions and local market specificities.

9.

In order to reduce primary energy consumption, BAT is to consider cogeneration/combined heat and power plants.

The employment of cogeneration plants for the production of steam and electricity or combined heat and power plants can be applied in the cement industry by recovering waste heat from the clinker cooler or kiln flue-gases using the conventional steam cycle processes or other techniques. Furthermore, excess heat can be recovered from the clinker cooler or kiln flue-gases for district heating or industrial applications.

The technique is applicable in all cement kilns if sufficient excess heat is available, if appropriate process parameters can be met, and if economic viability is ensured.

10.

In order to reduce/minimise electrical energy consumption, BAT is to use one or a combination of the following techniques:

Technique

a | Using power management systems

b | Using grinding equipment and other electricity based equipment with high energy efficiency

c | Using improved monitoring systems

d | Reducing air leaks into the system

e | Process control optimisation

11.

In order to guarantee the characteristics of the wastes to be used as fuels and/or raw materials in a cement kiln and reduce emissions, BAT is to apply the following techniques:

Technique

a |

Apply quality assurance systems to guarantee the characteristics of wastes and to analyse any waste that is to be used as raw material and/or fuel in a cement kiln for:

I.

constant quality

II.

physical criteria, e.g. emissions formation, coarseness, reactivity, burnability, calorific value

III.

chemical criteria, e.g. chlorine, sulphur, alkali and phosphate content and relevant metals content

b | Control the amount of relevant parameters for any waste that is to be used as raw material and/or fuel in a cement kiln, such as chlorine, relevant metals (e.g. cadmium, mercury, thallium), sulphur, total halogen content

c | Apply quality assurance systems for each waste load

Different types of waste materials can replace primary raw materials and/or fossil fuels in cement manufacturing and will contribute to saving natural resources.

12.

In order to ensure appropriate treatment of the wastes used as fuel and/or raw materials in the kiln, BAT is to use the following techniques:

Technique

a | Use appropriate points to feed the waste into the kiln in terms of temperature and residence time depending on kiln design and kiln operation

b | To feed waste materials containing organic components that can be volatilised before the calcining zone into the adequately high temperature zones of the kiln system

c | To operate in such a way that the gas resulting from the co-incineration of waste is raised in a controlled and homogeneous fashion, even under the most unfavourable conditions, to a temperature of 850 °C for 2 seconds

d | To raise the temperature to 1100 °C, if hazardous waste with a content of more than 1 % of halogenated organic substances, expressed as chlorine, are co-incinerated

e | To feed wastes continuously and constantly

f | Delay or stop co-incinerating waste for operations such as start-ups and/or shutdowns when appropriate temperatures and residence times cannot be reached, as noted in a) to d) above

13.

BAT is to apply safety management for the storage, handling and feeding of hazardous waste materials, such as using a risk-based approach according to the source and type of waste, for the labelling, checking, sampling and testing of waste to be handled.

14.

In order to minimise/prevent diffuse dust emissions from dusty operations, BAT is to use one or a combination of the following techniques:

Technique | Applicability

a | Use a simple and linear site layout of the installation | Applicable to new plants only

b | Enclose/encapsulate dusty operations, such as grinding, screening and mixing | Generally applicable

c | Cover conveyors and elevators, which are constructed as closed systems, if diffuse dust emissions are likely to be released from dusty material

d | Reduce air leakages and spillage points

e | Use automatic devices and control systems

f | Ensure trouble-free operations

g |

Ensure proper and complete maintenance of the installation using mobile and stationary vacuum cleaning.

During maintenance operations or in cases of trouble with conveying systems, spillage of materials can take place. To prevent the formation of diffuse dust during removal operations, vacuum systems should be used. New buildings can easily be equipped with stationary vacuum cleaning piping, while existing buildings are normally better fitted with mobile systems and flexible connections

This article is long: the rest is at the official publication.