Processing plants shall meet the following requirements, for processing by pressure sterilisation or in accordance with the processing methods referred to in Article 15(1)(b) of Regulation (EC) No 1069/2009:
Processing plants must not be situated on the same site as slaughterhouses or other establishments which have been approved or registered in accordance with Regulation (EC) No 852/2004 or Regulation (EC) No 853/2004, unless the risks to public and animal health resulting from the processing of animal by-products, which originate from such slaughterhouses or other establishments, are mitigated by compliance with at least the following conditions:
the processing plant must be physically separated from the slaughterhouse or other establishment, where appropriate by locating the processing plant in a building that is completely separated from the slaughterhouse or other establishment;
the following must be installed and operated in the processing plant:
a conveyer system which links the processing plant to the slaughterhouse or other establishment and which may not be by-passed,
separate entrances, reception bays, equipment and exits for both the processing plant and the slaughterhouse or establishment;
measures must be taken to prevent the spreading of risks through the operation of personnel which is employed in the processing plant and in the slaughterhouse or other establishment;
unauthorised persons and animals must not have access to the processing plant.
By way of derogation from points (i) to (iv), in the case of processing plants processing Category 3 material, the competent authority may authorise other conditions instead of those set out in those points, aimed at mitigating the risks to public and animal health, including the risks arising from the processing of Category 3 material, which originates from off-site establishments approved or registered in accordance with Regulation (EC) No 852/2004 or Regulation (EC) No 853/2004.
Member States shall inform the Commission and the other Member States in the framework of the Standing Committee on the Food Chain and Animal Health referred to in Article 52(1) of Regulation (EC) No 1069/2009 of the use made of this derogation by their competent authorities;
The processing plant must have a clean and unclean sector, adequately separated. The unclean sector must have a covered place to receive animal by-products and must be constructed in such a way that it is easy to clean and disinfect. Floors must be laid in such a way as to facilitate the draining of liquids;
The processing plant must have adequate facilities including lavatories, changing rooms and washbasins for staff;
The processing plant must have sufficient production capacity for hot water and steam for the processing of animal by-products;
The unclean sector must, if appropriate, contain equipment to reduce the size of animal by-products and equipment for loading the crushed animal by-products into the processing unit;
Where heat treatment is required, all installations must be equipped with:
measuring equipment to monitor temperature against time and, if applicable for the processing method used, pressure at critical points;
recording devices to record continuously the results of these measurements in a way so that they remain accessible for the purpose of checks and official controls;
an adequate safety system to prevent insufficient heating;
To prevent recontamination of the derived product by the introduction of animal by-products, there must be a clear separation between the area of the plant where incoming material for processing is unloaded and the areas set aside for the processing of that product and the storage of the derived product.
The processing plant must have adequate facilities for cleaning and disinfecting the containers or receptacles in which animal by-products are received and the means of transport, other than ships, in which they are transported.
Adequate facilities must be provided for the disinfecting of vehicle wheels and the other parts of the vehicle, as appropriate, on leaving the unclean sector of the processing plant.
All processing plants must have a waste-water disposal system meeting the requirements set out by the competent authority in accordance with Union legislation.
The processing plant must have its own laboratory or make use of the services of an external laboratory. The laboratory must be equipped to carry out necessary analyses and be approved by the competent authority on the basis of an assessment of the capacity of the laboratory to carry out those analyses, be accredited according to internationally recognised standards or be subject to regular controls by the competent authority, to assess the capacity of the laboratory to carry out those analyses.
If on the basis of a risk assessment, the volume of products treated requires the regular or permanent presence of the competent authority, the processing plants must have an adequately equipped lockable room for the exclusive use of the inspection service.
Processing plants processing Category 1 material and other premises where specified risk material is removed, slaughterhouses and processing plants processing Category 2 material shall have a pre-treatment process for the retention and collection of animal material as an initial step in the treatment of wastewater.
The equipment used in the pre-treatment process shall consist of drain traps or screens with apertures with a filter pore or a mesh size of no more than 6 mm in the downstream end of the process or equivalent systems that ensure that the solid particles in the wastewater passing through them are no more than 6 mm.
Wastewater from the premises as referred to in point 1 must enter a pre-treatment process which shall ensure that all wastewater has been filtered through the process before being drained off the premises. No grinding, maceration or any other processing or application of pressure shall be carried out which could facilitate the passage of solid animal material through the pre-treatment process.
All animal material retained in the pre-treatment process in premises as referred to in point 1 shall be collected and transported as Category 1 or Category 2 material, as appropriate, and disposed of in accordance with Regulation (EC) No 1069/2009.
Wastewater having passed the pre-treatment process in premises referred to in point 1 and wastewater from other premises handling or processing animal by-products shall be treated in accordance with Union legislation, without restrictions in accordance with this Regulation.
In addition to the requirements laid down in point 4, the competent authority may oblige operators to treat wastewater originating in the unclean sector of processing plants and in plants or establishments carrying out intermediate operations with Category 1 material or Category 2 material or storing Category 1 material or Category 2 material, in accordance with conditions which ensure that risks from pathogens are mitigated.
Without prejudice to points 1 to 5, the disposal of animal by-products, including blood and milk, or derived products through the wastewater stream shall be prohibited.
However, Category 3 material comprising of centrifuge or separator sludge may be disposed of through the wastewater stream, provided that it has been subject to one of the treatments for centrifuge or separator sludge set out in Part III of Section 4 of Chapter II of Annex X hereto.
The layout of processing plants processing Category 1 and Category 2 materials must ensure the total separation of Category 1 material from Category 2 material from reception of the raw material until dispatch of the resulting derived product, unless a mixture of Category 1 material and Category 2 material is processed as Category 1 material.
The following requirements shall apply in addition to the general conditions set out in Section 1:
Processing plants processing Category 3 materials shall not be located at the same site as processing plants processing Category 1 or Category 2 materials, unless located in a completely separate building.
However, the competent authority may authorise the processing of Category 3 material on a site where handling or processing of Category 1 or Category 2 material takes place, if cross-contamination is prevented due to:
the layout of the premises, in particular the arrangements for the reception, and by way of the further handling of raw materials;
the layout and the management of the equipment used for processing, including the layout and the management of separate processing lines or of cleaning procedures which are excluding the propagation of any possible risks to public and animal health; and
the layout and the management of the areas for the temporary storage of the end products.
Processing plants processing Category 3 material shall have in place an installation to check the presence of foreign bodies, such as packaging material or metallic pieces, in the animal by-products or derived products, if they are processing materials which are destined for feeding. Such foreign bodies shall be removed before or during processing.
In addition to the general hygiene requirements provided for in Article 25 of Regulation (EC) No 1069/2009, processing plants shall have a documented pest control programme in place for the implementation of the arrangements for protection against pests, such as insects, rodents and birds, referred to in Article 25(1)(c) of that Regulation.
Accurately calibrated gauges/recorders must be used to monitor continuously the processing conditions. Records must be kept to show the date of calibration of gauges/recorders.
Material that may not have received the specified heat treatment, such as material discharged at start up or leakage from cookers, must be recirculated through the heat treatment or collected and reprocessed or disposed of in accordance with Regulation (EC) No 1069/2009.
Unless the competent authority requires the application of pressure sterilisation (method 1), Category 1 and Category 2 material shall be processed in accordance with processing methods 2, 3, 4 or 5 as referred to in Chapter III.
The critical control points that determine the extent of the heat treatments applied in processing shall include for each processing method as specified in Chapter III:
raw material particle size;
temperature achieved in the heat treatment process;
pressure, if applied to the raw material;
duration of the heat treatment process or feed rate to a continuous system. Minimum processing standards must be specified for each applicable critical control point.
In the case of chemical treatments which have been authorised by the competent authority as processing method 7 in accordance with point G of Chapter III, the critical control points that determine the extent of the chemical treatments applied shall include the pH adjustment achieved.
Records shall be maintained for at least two years to show that the minimum process values for each critical control point are applied.
Category 3 material shall be processed in accordance with any of the processing methods 1 to 5 or processing method 7, or, in the case of material originating from aquatic animals, with any of the processing methods 1 to 7, as referred to in Chapter III.
If the particle size of the animal by-products to be processed is more than 50 millimetres, the animal by-products must be reduced in size using appropriate equipment, set so that the particle size after reduction is no greater than 50 millimetres. The effectiveness of the equipment must be checked daily and its condition recorded. If checks disclose the existence of particles larger than 50 millimetres, the process must be stopped and repairs made before the process is resumed.
The animal by-products with the particle size of no greater than 50 millimetres must be heated to a core temperature of more than 133 °C for at least 20 minutes without interruption at a pressure (absolute) of at least 3 bars. The pressure must be produced by the evacuation of all air in the sterilisation chamber and the replacement of the air by steam (‘saturated steam’); the heat treatment may be applied as the sole process or as a pre- or post-process sterilisation phase.
The processing may be carried out in batch or continuous systems.
If the particle size of the animal by-products to be processed is more than 150 millimetres, the animal by-products must be reduced in size using appropriate equipment, set so that the particle size after reduction is no greater than 150 millimetres. The effectiveness of the equipment must be checked daily and its condition recorded. If checks disclose the existence of particles larger than 150 millimetres, the process must be stopped and repairs made before the process is resumed.
After reduction the animal by-products must be heated in a manner which ensures that a core temperature greater than 100 °C is achieved for at least 125 minutes, a core temperature greater than 110 °C is achieved for at least 120 minutes and a core temperature greater that 120 °C is achieved for at least 50 minutes.
The core temperatures may be achieved consecutively or through a coincidental combination of the time periods indicated.
The processing must be carried out in a batch system.
If the particle size of the animal by-products to be processed is more than 30 millimetres, the animal by-products must be reduced in size using appropriate equipment, set so that the particle size after reduction is no greater than 30 millimetres. The effectiveness of the equipment must be checked daily and its condition recorded. If checks disclose the existence of particles larger than 30 millimetres, the process must be stopped and repairs made before the process is resumed.
After reduction the animal by-products must be heated in a manner which ensures that a core temperature greater than 100 °C is achieved for at least 95 minutes, a core temperature greater than 110 °C is achieved for at least 55 minutes and a core temperature greater that 120 °C is achieved for at least 13 minutes.
The core temperatures may be achieved consecutively or through a coincidental combination of the time periods indicated.
The processing may be carried out in batch or continuous systems.
If the particle size of the animal by-products to be processed is more than 30 millimetres, the animal by-products must be reduced in size using appropriate equipment, set so that the particle size after reduction is no greater than 30 millimetres. The effectiveness of the equipment must be checked daily and its condition recorded. If checks disclose the existence of particles larger than 30 millimetres, the process must be stopped and repairs made before the process is resumed.
After reduction the animal by-products must be placed in a vessel with added fat and heated in a manner which ensures that a core temperature greater than 100 °C is achieved for at least 16 minutes, a core temperature greater than 110 °C is achieved for at least 13 minutes, a core temperature greater than 120 °C is achieved for at least eight minutes and a core temperature greater that 130 °C is achieved for at least three minutes.
The core temperatures may be achieved consecutively or through a coincidental combination of the time periods indicated.
The processing may be carried out in batch or continuous systems.
If the particle size of the animal by-products to be processed is more than 20 millimetres, the animal by-products must be reduced in size using appropriate equipment, set so that the particle size after reduction is no greater than 20 millimetres. The effectiveness of the equipment must be checked daily and its condition recorded. If checks disclose the existence of particles larger than 20 millimetres, the process must be stopped and repairs made before the process is resumed.
After reduction the animal by-products must be heated until they coagulate and then pressed so that fat and water are removed from the proteinaceous material. The proteinaceous material must then be heated in a manner which ensures that a core temperature greater than 80 °C is achieved for at least 120 minutes and a core temperature greater that 100 °C is achieved for at least 60 minutes.
The core temperatures may be achieved consecutively or through a coincidental combination of the time periods indicated.
The processing may be carried out in batch or continuous systems.
The animal by-products must be reduced to a particle size which is no greater than:
50 mm, in case of heat treatment in accordance with point 2(a); or
30 mm, in case of heat treatment in accordance with point 2(b).
They must then be mixed with formic acid to reduce and maintain the pH to 4,0 or lower. The mixture must be stored for at least 24 hours pending further treatment.
After reduction, the mixture must be heated to:
a core temperature of at least 90 °C for at least 60 minutes; or
a core temperature of at least 70 °C for at least 60 minutes.
When using a continuous flow system, the progression of the product through the heat converter must be controlled by means of mechanical commands limiting its displacement in such way that at the end of the heat treatment operation the product has undergone a cycle which is sufficient in both time and temperature.
The processing may be carried out in batch or continuous systems.
Any processing method authorised by the competent authority where the following have been demonstrated by the operator to that authority:
the identification of relevant hazards in the starting material, in view of the origin of the material, and of the potential risks in view of the animal health status of the Member State or the area or zone where the method is to be used;
the capacity of the processing method to reduce those hazards to a level which does not pose any significant risks to public and animal health;
the sampling of the final product on a daily basis over a period of 30 production days in compliance with the following microbiological standards:
Samples of material taken directly after the treatment:
Clostridium perfringens absent in 1 g of the products
Samples of material taken during or upon withdrawal from storage:
Salmonella: absence in 25g: n=5, c=0, m=0, M=0
Enterobacteriaceae: n=5, c=2; m=10; M=300 in 1 g
where:
nnumber of samples to be tested;
mthreshold value for the number of bacteria; the result is considered satisfactory if the number of bacteria in all samples does not exceed m;
Mmaximum value for the number of bacteria; the result is considered unsatisfactory if the number of bacteria in one or more samples is M or more; and
cnumber of samples the bacterial count of which may be between m and M, the samples still being considered acceptable if the bacterial count of the other samples is m or less.
Details of the critical control points under which each processing plant satisfactorily complies with the microbiological standards must be recorded and maintained so that the operator and the competent authority can monitor the operation of the processing plant. The information to be recorded and monitored must include the particle size, and, as appropriate, the critical temperature, the absolute time, pressure profile, raw material feed rate and fat recycling rate.
By way of derogation from point 1, the competent authority may authorise the use of processing methods which have been approved prior to the date of entry into application of this Regulation, in accordance with Chapter III of Annex V to Regulation (EC) No 1774/2002.
The competent authority shall permanently or temporarily suspend the application of processing methods referred to in points 1 and 3, if it obtains evidence that any of the circumstances specified in point 1(a) or (b) have substantially changed.
The competent authority shall inform the competent authority of another Member State upon request about the information at its disposal under points 1 and 2 in relation to an authorised processing method.
Materials resulting from the processing of Category 1 and 2 materials shall be permanently marked in accordance with the requirements for the marking of certain derived products set out in Chapter V of Annex VIII.
However, such marking shall not be required for the following materials referred to in Section 2:
biodiesel produced in accordance with point D;
hydrolysed materials referred to in point H;
mixtures of pig and poultry manure with quick lime produced in accordance with point I;
renewable fuels produced from rendered fats, which are derived from Category 1 and Category 2 materials, in accordance with point J and L.
The competent authority of a Member State shall make the results of official controls available to the competent authority of another Member State upon request, when an alternative method is used for the first time in that Member State, in order to facilitate the introduction of the new alternative method.
For this process, animal by-products of all categories may be used.
Alkaline hydrolysis shall be carried out according to the following processing standards:
Either a sodium hydroxide (NaOH) or potassium hydroxide (KOH) solution (or a combination thereof) must be used in an amount that assures approximate molar equivalency to the weight, type and composition of the animal by-products to be digested.
In the case of high fat in the animal by-products that neutralises the base, the added base must be adjusted so that the molar equivalency referred to is achieved.
Animal by-products must be placed in a steel alloy container. The measured amount of alkali must be added either in solid form or as a solution as referred to in point (a).
The container must be closed and the animal by-products and alkali mixture must be heated to a core temperature of at least 150 °C and at a pressure (absolute) of at least 4 bars for at least:
three hours without interruption;
six hours without interruption in case of treatment of animal by-products referred to in Article 8(a)(i) and (ii) of Regulation (EC) No 1069/2009.