[Member States must allow the usage of adjacent frequency bands within this table as a single frequency band provided the specific conditions of each of these adjacent frequency bands are met.] [Member States must allow the usage of spectrum up to the transmit power, field strength or power density given in this table. In conformity with Article 3(3) of Decision 2006/771/EC, they may impose less restrictive conditions, i.e. allow the use of spectrum with higher transmit power, field strength or power density.] [Member States may only impose these “additional parameters (channelling and/or channel access and occupation rules)”, and may not add other parameters or spectrum access and mitigation requirements. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may completely omit the “additional parameters (channelling and/or channel access and occupation rules)” in a given cell or allow higher values.] [Member States may only impose these “other usage restrictions”, and may not add additional usage restrictions. As less restrictive conditions may be introduced within the meaning of Article 3(3) of Decision 2006/771/EC, Member States may omit one or all of these restrictions.] [This category is available for any type of application which fulfils the technical conditions (typical uses are telemetry, telecommand, alarms, data in general and other similar applications).] [For this frequency band Member States must make all the alternative sets of usage conditions possible.] [“Duty cycle” means the ratio of time during any one-hour period when equipment is actively transmitting. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may allow a higher value for “Duty cycle”.] [Social alarm devices are used to assist elderly or disabled people when they are in distress.] [This category covers, for example, devices for car immobilisation, animal identification, alarm systems, cable detection, waste management, personal identification, wireless voice links, access control, proximity sensors, anti-theft systems, including RF anti-theft induction systems, data transfer to handheld devices, automatic article identification, wireless control systems and automatic road tolling.] [This category covers inductive applications used for radio frequency identification (RFID).] [This category covers inductive applications used for electronic article surveillance (EAS).] [This category covers the radio part of active implantable medical devices, as defined in Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member States relating to active implantable medical devices (OJ L 189, 20.7.1990, p. 17).] [This category covers systems specifically designed for the purpose of providing non-voice digital communications between active medical implants, as defined in footnote 19, and/or body-worn devices and other devices external to the human body used for transferring non-time critical individual patient-related physiological information.] [This category covers transmitting devices which are placed inside the body of an animal for the purpose of performing diagnostic functions and/or delivery of therapeutic treatment.] [This category includes applications which connect personal audio devices, including mobile phones, and the automotive or home entertainment system.] [Applications for wireless audio systems, including: wireless microphones; cordless loudspeakers; cordless headphones; cordless headphones for portable use, e.g. portable CD, cassette or radio devices carried on a person; cordless headphones for use in a vehicle, for example for use with a radio or mobile telephone, etc.; in-ear monitoring and wireless microphones for use at concerts or other stage productions.] [This category covers applications used for determining the position, velocity and/or other characteristics of an object, or for obtaining information relating to these parameters.] [Tank level probing radars (TLPR) are a specific type of radio-determination application, which are used for tank level measurements and are installed in metallic or reinforced concrete tanks, or similar structures made of material with comparable attenuation characteristics. The purpose of the tank is to contain a substance.] [The power limit applies inside a closed tank and corresponds to a spectral density of – 41,3 dBm/MHz e.i.r.p. outside a 500 litre test tank.] [This category covers applications used to control the movement of models (principally miniature representations of vehicles) in the air, on land or over or under the water surface.’]
Type of short-range device | Frequency band | Transmit power limit/field strength limit/power density limit | Additional parameters (channelling and/or channel access and occupation rules) | Other usage restrictions | Implementation deadline
Non-specific short-range devices | 6765–6795 kHz | 42 dBμA/m at 10 metres | | | 1 October 2008
13,553–13,567 MHz | 42 dBμA/m at 10 metres | | | 1 October 2008
26,957–27,283 MHz | 10 mW effective radiated power (e.r.p.), which corresponds to 42 dBμA/m at 10 metres | | Video applications are excluded | 1 June 2007
40,660–40,700 MHz | 10 mW e.r.p. | | Video applications are excluded | 1 June 2007
433,050–434,040 MHz |
1 mW e.r.p.
and - 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz
Voice applications allowed with advanced mitigation techniques | Audio and video applications are excluded | 1 November 2010
10 mW e.r.p. | Duty cycle limit: 10 % | Analogue audio applications other than voice are excluded. Analogue video applications are excluded | 1 November 2010
434,040–434,790 MHz |
1 mW e.r.p.
and – 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz
Voice applications allowed with advanced mitigation techniques | Audio and video applications are excluded | 1 November 2010
10 mW e.r.p. | Duty cycle limit: 10 % | Analogue audio applications other than voice are excluded. Analogue video applications are excluded | 1 November 2010
Duty cycle limit: 100 % subject to channel spacing up to 25 kHz
Voice applications allowed with advanced mitigation techniques
Audio and video applications are excluded | 1 November 2010
Non-specific short-range devices (cont.) | 863,000–865,000 MHz | 25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used | Analogue audio applications other than voice are excluded. Analogue video applications are excluded | 1 November 2010
865,000–868,000 MHz | 25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 1 % may also be used | Analogue audio applications other than voice are excluded. Analogue video applications are excluded | 1 November 2010
868,000–868,600 MHz | 25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 1 % may also be used | Analogue video applications are excluded | 1 November 2010
868,700–869,200 MHz | 25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used | Analogue video applications are excluded | 1 November 2010
869,400–869,650 MHz | 500 mW e.r.p. |
Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 10 % may also be used
Channel spacing must be 25 kHz, except that the whole band may also be used as a single channel for high-speed data transmission
Analogue video applications are excluded | 1 November 2010
25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used | Analogue audio applications other than voice are excluded. Analogue video applications are excluded | 1 November 2010
Non-specific short-range devices (cont.) | 869,700–870,000 MHz | 5 mW e.r.p. | Voice applications allowed with advanced mitigation techniques | Audio and video applications are excluded | 1 June 2007
25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 1 % may also be used | Analogue audio applications other than voice are excluded. Analogue video applications are excluded | 1 November 2010
2400–2483,5 MHz | 10 mW equivalent isotropic radiated power (e.i.r.p.) | | | 1 June 2007
5725–5875 MHz | 25 mW e.i.r.p. | | | 1 June 2007
24,150–24,250 GHz | 100 mW e.i.r.p. | | | 1 October 2008
61,0–61,5 GHz | 100 mW e.i.r.p. | | | 1 October 2008
122–123 GHz | 100 mW e.i.r.p. | | | 1 June 2012
244–246 GHz | 100 mW e.i.r.p. | | | 1 June 2012
Wideband data transmission systems | 2400–2483,5 MHz |
100 mW e.i.r.p.
and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used
Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used | | 1 November 2009
57,0–66,0 GHz |
40 dBm e.i.r.p.
and 13 dBm/MHz e.i.r.p. density
Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used | Fixed outdoor installations are excluded | 1 November 2010
Alarm systems | 868,600–868,700 MHz | 10 mW e.r.p. |
Channel spacing: 25 kHz
The whole frequency band may also be used as a single channel for high-speed data transmission
Duty cycle limit: 1,0 %
1 October 2008
869,250–869,300 MHz | 10 mW e.r.p. |
Channel spacing: 25 kHz
Duty cycle limit: 0,1 %
1 June 2007
869,300–869,400 MHz | 10 mW e.r.p. |
Channel spacing: 25 kHz
Duty cycle limit: 1,0 %
1 October 2008
869,650–869,700 MHz | 25 mW e.r.p. |
Channel spacing: 25 kHz
Duty cycle limit: 10 %
1 June 2007
Social alarms | 869,200–869,250 MHz | 10 mW e.r.p. |
Channel spacing: 25 kHz
Duty cycle limit: 0,1 %
1 June 2007
Inductive applications | 9,000–59,750 kHz | 72 dBμA/m at 10 metres | | | 1 November 2010
59,750–60,250 kHz | 42 dBμA/m at 10 metres | | | 1 June 2007
60,250–74,750 kHz | 72 dBμA/m at 10 metres | | | 1 June 2012
74,750–75,250 kHz | 42 dBμA/m at 10 metres | | | 1 June 2012
75,250–77,250 kHz | 72 dBμA/m at 10 metres | | | 1 June 2012
77,250–77,750 kHz | 42 dBμA/m at 10 metres | | | 1 June 2012
77,750–90 kHz | 72 dBμA/m at 10 metres | | | 1 June 2012
90–119 kHz | 42 dBμA/m at 10 metres | | | 1 June 2012
119–128,6 kHz | 66 dBμA/m at 10 metres | | | 1 June 2012
128,6–129,6 kHz | 42 dBμA/m at 10 metres | | | 1 June 2012
129,6–135 kHz | 66 dBμA/m at 10 metres | | | 1 June 2012
135–140 kHz | 42 dBμA/m at 10 metres | | | 1 June 2012
140–148,5 kHz | 37,7 dBμA/m at 10 metres | | | 1 October 2008
148,5–5000 kHz
In the specific bands mentioned below, higher field strengths and additional usage restrictions apply:
15 dBμA/m at 10 metres in any bandwidth of 10 kHz
Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz
1 October 2008
Inductive applications (cont.) | 400–600 kHz | – 8 dBμA/m at 10 metres | | This set of usage conditions applies to RFID only | 1 October 2008
3155–3400 kHz | 13,5 dBμA/m at 10 metres | | | 1 October 2008
5000–30000 kHz
In the specific bands mentioned below, higher field strengths and additional usage restrictions apply:
20 dBμA/m at 10 metres in any bandwidth of 10 kHz
Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz
1 October 2008
6765–6795 kHz | 42 dBμA/m at 10 metres | | | 1 June 2007
7400–8800 kHz | 9 dBμA/m at 10 metres | | | 1 October 2008
10200–11000 kHz | 9 dBμA/m at 10 metres | | | 1 October 2008
13553–13567 kHz | 42 dBμA/m at 10 metres | | | 1 June 2007
60 dBμA/m at 10 metres | | This set of usage conditions applies to RFID and EAS only | 1 October 2008
26957–27283 kHz | 42 dBμA/m at 10 metres | | | 1 October 2008
Active medical implants | 9–315 kHz | 30 dBμA/m at 10m | Duty cycle limit: 10 % | | 1 October 2008
30,0–37,5 MHz | 1 mW e.r.p. | Duty cycle limit: 10 % | This set of usage conditions applies to ultra low power medical membrane implants for blood pressure measurements only | 1 November 2010
402–405 MHz | 25 μW e.r.p. |
Channel spacing: 25 kHz
Individual transmitters may combine adjacent channels for increased bandwidth up to 300 kHz.
Other techniques to access spectrum or mitigate interference, including bandwidths greater than 300 kHz, can be used provided they result at least in an equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC to ensure compatible operation with the other users and in particular with meteorological radiosondes
1 November 2009
Active medical implants and associated peripherals | 401–402 MHz | 25 μW e.r.p. |
Channel spacing: 25 kHz
Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz.
Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used
1 November 2010
405–406 MHz | 25 μW e.r.p. |
Channel spacing: 25 kHz
Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz.
Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used
1 November 2010
Animal implantable devices | 315–600 kHz | – 5 dΒμΑ/m at 10m | Duty cycle limit: 10 % | | 1 November 2010
12,5–20,0 MHz | – 7 dΒμΑ/m at 10m in a bandwidth of 10 kHz | Duty cycle limit: 10 % | This set of usage conditions applies to indoor applications only | 1 November 2010
Low power FM transmitters | 87,5–108,0 MHz | 50 nW e.r.p. | Channel spacing up to 200 kHz | | 1 November 2010
Wireless audio applications | 863–865 MHz | 10 mW e.r.p. | | | 1 November 2010
Radio determination applications | 2400–2483,5 MHz | 25 mW e.i.r.p. | | | 1 November 2009
17,1–17,3 GHz | 26 dBm e.i.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used | This set of usage conditions applies to ground-based systems only | 1 November 2009
Tank level probing radar | 4,5–7,0 GHz | 24 dBm e.i.r.p. | | | 1 November 2009
8,5–10,6 GHz | 30 dBm e.i.r.p. | | | 1 November 2009
24,05–27,0 GHz | 43 dBm e.i.r.p. | | | 1 November 2009
57,0–64,0 GHz | 43 dBm e.i.r.p. | | | 1 November 2009
75,0–85,0 GHz | 43 dBm e.i.r.p. | | | 1 November 2009
Model control | 26990–27000 kHz | 100 mW e.r.p. | | | 1 November 2009
27040–27050 kHz | 100 mW e.r.p. | | | 1 November 2009
27090–27100 kHz | 100 mW e.r.p. | | | 1 November 2009
27140–27150 kHz | 100 mW e.r.p. | | | 1 November 2009
27190–27200 kHz | 100 mW e.r.p. | | | 1 November 2009
Radio frequency identification (RFID) | 2446–2454 MHz | 500 mW e.i.r.p. | | | 1 June 2012
Road transport and traffic telematics | 24,050–24,075 GHz | 100 mW e.i.r.p. | | | 1 June 2012
24,075–24,150 GHz | 0,1 mW e.i.r.p. | | | 1 June 2012
24,075–24,150 GHz | 100 mW e.i.r.p. |
Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used
Dwell time limits and frequency modulation range apply as specified in harmonised standards
This set of usage conditions applies to vehicle radars only | 1 June 2012
24,150–24,250 GHz | 100 mW e.i.r.p. | | | 1 June 2012
63–64 GHz | 40 dBm e.i.r.p. | | This set of usage conditions applies to vehicle-to-vehicle, vehicle-to-infrastructure and infrastructure-to-vehicle systems only | 1 June 2012
76,0–77,0 GHz |
55 dBm peak e.i.r.p. and
50 dBm mean e.i.r.p. and
23,5 dBm mean e.i.r.p. for pulse radars
This set of usage conditions applies to terrestrial vehicle and infrastructure systems only | 1 November 2010