2 ‘ANNEX, Decision_act (EU) 2009/381

In forcesince 13 May 2009

[Member States must allow the usage of spectrum up to the power, field strength or power density given in this table. In conformity with Article 3(3) of Decision 2006/771/EC, they may impose less restrictive conditions, i.e. allow the use of spectrum with higher power, field strength or power density.] [Member States may only impose these “additional parameters/spectrum access and mitigation requirements”, and may not add other parameters or spectrum access and mitigation requirements. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may completely omit the parameters/spectrum access and mitigation requirements in a given cell or allow higher values.] [Member States may only impose these “other usage restrictions”, and may not add additional usage restrictions. As less restrictive conditions may be introduced within the meaning of Article 3(3) of Decision 2006/771/EC, Member States may omit one or all of these restrictions.] [This category is available for any type of application which fulfils the technical conditions (typical uses are telemetry, telecommand, alarms, data in general and other similar applications).] [For this frequency band Member States must make all the alternative sets of usage conditions possible.] [“Duty cycle” means the ratio of time during any one-hour period when equipment is actively transmitting. Less restrictive conditions within the meaning of Article 3(3) of Decision 2006/771/EC mean that Member States may allow a higher value for “Duty cycle”.] [Social alarm devices are used to assist elderly or disabled people when they are in distress.] [This category covers, for example, devices for car immobilisation, animal identification, alarm systems, cable detection, waste management, personal identification, wireless voice links, access control, proximity sensors, anti-theft systems, including RF anti-theft induction systems, data transfer to handheld devices, automatic article identification, wireless control systems and automatic road tolling.] [This category covers inductive applications used for Radio Frequency Identification (RFID).] [This category covers inductive applications used for Electronic Article Surveillance (EAS).] [This category covers the radio part of active implantable medical devices, as defined in Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member States relating to active implantable medical devices (OJ L 189, 20.7.1990, p. 17).] [Applications for wireless audio systems, including: cordless loudspeakers; cordless headphones; cordless headphones for portable use, e.g. portable CD, cassette or radio devices carried on a person; cordless headphones for use in a vehicle, for example for use with a radio or mobile telephone, etc.; in-ear monitoring, for use at concerts or other stage productions.] [This category covers applications used for determining the position, velocity and/or other characteristics of an object, or for obtaining information relating to these parameters.] [Tank Level Probing Radars (TLPR) are a specific type of radiodetermination application, which are used for tank level measurements and are installed in metallic or reinforced concrete tanks, or similar structures made of material with comparable attenuation characteristics. The purpose of the tank is to contain a substance.] [The power limit applies inside a closed tank and corresponds with a spectral density of – 41,3 dBm/MHz e.i.r.p. outside a 500 litre test tank.] [This category covers applications used to control the movement of models (principally miniature representations of vehicles) in the air, on land or over or under the water surface.’]

Type of short-range device | Frequency band | Power limit/field strength limit/power density limit | Additional parameters/spectrum access and mitigation requirements | Other usage restrictions | Implementation deadline

Non-specific short-range devices | 6765–6795 kHz | 42 dBμA/m at 10 metres | | | 1 October 2008

13,553–13,567 MHz | 42 dBμA/m at 10 metres | | | 1 October 2008

26,957–27,283 MHz | 10 mW effective radiated power (e.r.p.), which corresponds to 42 dBμA/m at 10 metres | | Video applications are excluded | 1 June 2007

40,660–40,700 MHz | 10 mW e.r.p. | | Video applications are excluded | 1 June 2007

433,050–434,040 MHz |

1 mW e.r.p.

and – 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz

Audio and voice signals, and video applications, are excluded | 1 October 2008

10 mW e.r.p. | Duty cycle: 10 % | Audio and voice signals, and video applications, are excluded | 1 June 2007

434,040–434,790 MHz |

1 mW e.r.p.

and – 13dBm/10 kHz power density for bandwidth modulation larger than 250 kHz

Audio and voice signals, and video applications, are excluded | 1 October 2008

10 mW e.r.p. | Duty cycle: 10 % | Audio and voice signals, and video applications, are excluded | 1 June 2007

Duty cycle: 100 % subject to channel spacing up to 25 kHz | Audio and voice signals, and video applications, are excluded | 1 October 2008

863,000–868,000 MHz | 25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 0,1 % may also be used | Audio and voice signals, and video applications, are excluded | 1 October 2008

868,000–868,600 MHz | 25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 1 % may also be used | Video applications are excluded | 1 October 2008

25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 0,1 % may also be used | Audio and voice signals, and video applications, are excluded | 1 October 2008

868,700–869,200 MHz | 25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 0,1 % may also be used | Video applications are excluded | 1 October 2008

25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 0,1 % may also be used | Audio and voice signals, and video applications, are excluded | 1 October 2008

869,400–869,650 MHz | 500 mW e.r.p. |

Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 10 % may also be used

Channel spacing must be 25 kHz, except that the whole band may also be used as a single channel for high-speed data transmission

Video applications are excluded | 1 October 2008

25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 0,1 % may also be used | Audio and voice signals, and video applications, are excluded | 1 October 2008

869,700–870,000 MHz | 5 mW e.r.p. | Voice applications allowed with advanced mitigation techniques | Audio and video applications are excluded | 1 June 2007

25 mW e.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle of 0,1 % may also be used | Audio and voice signals, and video applications, are excluded | 1 October 2008

2400–2483,5 MHz | 10 mW equivalent isotropic radiated power (e.i.r.p.) | | | 1 June 2007

5725–5875 MHz | 25 mW e.i.r.p. | | | 1 June 2007

24,150–24,250 GHz | 100 mW e.i.r.p. | | | 1 October 2008

61,0–61,5 GHz | 100 mW e.i.r.p. | | | 1 October 2008

Wideband data transmission systems | 2400–2483,5 MHz |

100 mW e.i.r.p.

and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used

Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used | | 1 November 2009

57,0–66,0 GHz |

40 dBm e.i.r.p.

and 13 dBm/MHz e.i.r.p. density

Outdoor applications are excluded | 1 November 2009

25 dBm e.i.r.p.

and – 2 dBm/MHz e.i.r.p. density

Fixed outdoor installations are excluded | 1 November 2009

Alarm systems | 868,600–868,700 MHz | 10 mW e.r.p. |

Channel spacing: 25 kHz

The whole frequency band may also be used as a single channel for high-speed data transmission

Duty cycle: 1,0 %

1 October 2008

869,250–869,300 MHz | 10 mW e.r.p. |

Channel spacing: 25 kHz

Duty cycle: 0,1 %

1 June 2007

869,300–869,400 MHz | 10 mW e.r.p. |

Channel spacing: 25 kHz

Duty cycle: 1,0 %

1 October 2008

869,650–869,700 MHz | 25 mW e.r.p. |

Channel spacing: 25 kHz

Duty cycle: 10 %

1 June 2007

Social alarms | 869,200–869,250 MHz | 10 mW e.r.p. |

Channel spacing: 25 kHz

Duty cycle: 0,1 %

1 June 2007

Inductive applications | 20,050–59,750 kHz | 72 dBμA/m at 10 metres | | | 1 June 2007

59,750–60,250 kHz | 42 dBμA/m at 10 metres | | | 1 June 2007

60,250–70,000 kHz | 69 dBμA/m at 10 metres | | | 1 June 2007

70–119 kHz | 42 dBμA/m at 10 metres | | | 1 June 2007

119–127 kHz | 66 dBμA/m at 10 metres | | | 1 June 2007

127–140 kHz | 42 dBμA/m at 10 metres | | | 1 October 2008

140–148,5 kHz | 37,7 dBμA/m at 10 metres | | | 1 October 2008

148,5–5000 kHz

In the specific bands mentioned below, higher field strengths and additional usage restrictions apply:

–

15 dBμA/m at 10 metres in any bandwidth of 10 kHz

Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz

1 October 2008

400–600 kHz | – 8 dBμA/m at 10 metres | | This set of usage conditions applies to RFID only | 1 October 2008

3155–3400 kHz | 13,5 dBμA/m at 10 metres | | | 1 October 2008

5000–30000 kHz

In the specific bands mentioned below, higher field strengths and additional usage restrictions apply:

–

20 dBμA/m at 10 metres in any bandwidth of 10 kHz

Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz

1 October 2008

6765–6795 kHz | 42 dBμA/m at 10 metres | | | 1 June 2007

7400–8800 kHz | 9 dBμA/m at 10 metres | | | 1 October 2008

10200–11000 kHz | 9 dBμA/m at 10 metres | | | 1 October 2008

13553–13567 kHz | 42 dBμA/m at 10 metres | | | 1 June 2007

60 dBμA/m at 10 metres | | This set of usage conditions applies to RFID and EAS only | 1 October 2008

26957–27283 kHz | 42 dBμA/m at 10 metres | | | 1 October 2008

Active medical implants | 9–315 kHz | 30 dBμA/m at 10 m | Duty cycle: 10 % | | 1 October 2008

402–405 MHz | 25 μW e.r.p. |

Channel spacing: 25 kHz

Individual transmitters may combine adjacent channels for increased bandwidth up to 300 kHz.

Other techniques to access spectrum or mitigate interference, including bandwidths greater than 300 kHz, can be used provided they result at least in an equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC to ensure compatible operation with the other users and in particular with meteorological radiosondes.

1 November 2009

Wireless audio applications | 87,5–108,0 MHz | 50 nW e.r.p. | Channel spacing up to 200 kHz | | 1 October 2008

863–865 MHz | 10 mW e.r.p. | | | 1 June 2007

Radio determination applications | 2400–2483,5 MHz | 25 mW e.i.r.p. | | | 1 November 2009

17,1–17,3 GHz | 26 dBm e.i.r.p. | Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. | This set of usage conditions applies to ground based systems only | 1 November 2009

Tank Level Probing Radar | 4,5–7,0 GHz | 24 dBm e.i.r.p. | | | 1 November 2009

8,5–10,6 GHz | 30 dBm e.i.r.p. | | | 1 November 2009

24,05–27,0 GHz | 43 dBm e.i.r.p. | | | 1 November 2009

57,0–64,0 GHz | 43 dBm e.i.r.p. | | | 1 November 2009

75,0–85,0 GHz | 43 dBm e.i.r.p. | | | 1 November 2009

Model Control | 26990–27000 kHz | 100 mW e.r.p. | | | 1 November 2009

27040–27050 kHz | 100 mW e.r.p. | | | 1 November 2009

27090–27100 kHz | 100 mW e.r.p. | | | 1 November 2009

27140–27150 kHz | 100 mW e.r.p. | | | 1 November 2009

27190–27200 kHz | 100 mW e.r.p. | | | 1 November 2009

Radio Frequency Identification (RFID) | 2446–2454 MHz | 100 mW e.i.r.p. | | | 1 November 2009