The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, must show sufficient detail.
If the systems, components or separate technical units have electronic controls, information concerning their performance must be supplied.
0.1.
Make (trade name of manufacturer):
0.2.
Type and general commercial description(s):
0.3.
Means of identification of type, if marked on the vehicle (b):
0.3.1.
Location of that marking.
0.4.
Category of vehicle (c):
0.5.
Name and address of manufacturer:
0.8.
Address(es) of assembly plant(s):
1.1.
Photographs and/or drawings of a representative vehicle:
1.3.3.
Powered axles (number, position, interconnection):
1.6.
Position and arrangement of the engine:
2.4.
Range of vehicle dimensions (overall)
2.4.1.
For chassis without bodywork
2.4.1.1.
Length (j):
2.4.1.2.
Width (k):
2.4.2.
For chassis with bodywork
2.4.2.1.
Length (j):
2.4.2.2.
Width (k):
2.6.
Mass of the vehicle with bodywork in running order, or mass of the chassis with cab if the manufacturer does not fit the bodywork (with standard equipment, including coolant, oils, fuel, tools, spare wheel and driver) (o) (maximum and minimum):
3.1.
Manufacturer:
3.1.1.
Manufacturer's engine code: (As marked on the engine, or other means of identification)
3.2.
Internal combustion engine
3.2.1.1.
Working principle: positive ignition/compression ignition, four stroke/two stroke [Delete as applicable.]
3.2.1.2.
Number and arrangement of cylinders:
3.2.1.2.3.
Firing order:
3.2.1.3.
Engine capacity (s): cm3
3.2.1.8.
Maximum net power (t): kW at min–1 (manufacturer's declared value)
3.2.4.
Fuel feed
3.2.4.1.
By carburettor(s): yes/no [Delete as applicable.]
3.2.4.1.2.
Type(s):
3.2.4.1.3.
Number fitted:
3.2.4.2.
By fuel injection (compression ignition only): yes/no [Delete as applicable.]
3.2.4.2.2.
Working principle: Direct injection/pre-chamber/swirl chamber [Delete as applicable.]
3.2.4.2.4.
Governor
3.2.4.2.4.1.
Type:
3.2.4.2.4.2.1.
Cut-off point under load: min–1
3.2.4.3.
By fuel injection (positive ignition only): yes/no [Delete as applicable.]
3.2.4.3.1.
Working principle: Intake manifold (single-/multi-point [Delete as applicable.])/direct injection/other (specify) [Delete as applicable.]
3.2.8.
Intake system
3.2.8.4.2.
Air filter, drawings; or
3.2.8.4.2.1.
Make(s):
3.2.8.4.2.2.
Type(s):
3.2.8.4.3.
Intake silencer, drawings; or
3.2.8.4.3.1.
Make(s):
3.2.8.4.3.2.
Type(s):
3.2.9.
Exhaust system
3.2.9.2.
Description and/or drawing of the exhaust system:
3.2.9.4.
Exhaust silencer(s):
For front, centre, rear silencer: construction, type, marking, where relevant for exterior noise: reducing measures in the engine compartment and on the engine:
3.2.9.5.
Location of the exhaust outlet:
3.2.9.6.
Exhaust silencer containing fibrous materials:
3.2.12.2.1.
Catalytic convertor: yes/no [Delete as applicable.]
3.2.12.2.1.1.
Number of catalytic convertors and elements:
3.3.
Electric motor
3.3.1.
Type (winding, excitation):
3.3.1.1.
Maximum hourly output: kW
3.3.1.2.
Operating voltage: V
3.4.
Other engines or motors or combinations thereof (particulars regarding the parts of such engines or motors):
4.2.
Type (mechanical, hydraulic, electric, etc.):
4.6.
Gear ratios
[Continuously variable transmission]
Gear |
Internal gearbox ratios
(ratios of engine to gearbox output shaft revolutions)
Final drive ratio(s)
(ratio of gearbox output shaft to driven wheel revolutions)
Total gear ratios
Maximum for CVT
1
2
3
…
Minimum for CVT
Reverse
4.7.
Maximum vehicle speed (and gear in which this is achieved) (in km/h) (w):
6.6.
Tyres and wheels
6.6.2.
Upper and lower limits of rolling radii
6.6.2.1.
Axle 1:
6.6.2.2.
Axle 2:
6.6.2.3.
Axle 3:
6.6.2.4.
Axle 4:
etc.
9.1.
Type of bodywork:
9.2.
Materials used and method of construction
12.5.
Details of any non-engine devices designed to reduce noise (if not covered by other items):
Additional information in the case of off-road vehicles:
1.3.
Number of axles and wheels:
2.4.1.
For chassis without bodywork
2.4.1.4.1.
Approach angle (na): … degrees
2.4.1.5.1.
Departure angle (nb): … degrees
2.4.1.6.
Ground clearance (as defined in point 4.5 of section A of Annex II to Directive 70/156/EEC)
2.4.1.6.1.
Between the axles:
2.4.1.6.2.
Under the front axle(s):
2.4.1.6.3.
Under the rear axle(s):
2.4.1.7.
Ramp angle (nc): … degrees
2.4.2.
For chassis with bodywork
2.4.2.4.1.
Approach angle (na): … degrees
2.4.2.5.1.
Departure angle (nb): … degrees
2.4.2.6.
Ground clearance (as defined in point 4.5 of section A of Annex II to Directive 70/156/EEC)
2.4.2.6.1.
Between the axles:
2.4.2.6.2.
Under the front axle(s):
2.4.2.6.3.
Under the rear axle(s):
2.4.2.7.
Ramp angle (nc): … degrees
2.15.
Hill-starting ability (solo vehicle): … percent
4.9.
Differential lock: yes/no/optional [Delete as applicable.]
Date, File