The provisions for the inspection and verification of GLP which are contained in Parts A and B are those contained in Annexes I (Guides for compliance monitoring procedures for good laboratory practice) and II (Guidance for the conduct of test facility inspections and study audits) respectively of the OECD Council Decision-Recommendation on compliance with principles of good laboratory practice (C(89)87(Final)) of 2 October 1989 as revised by the OECD Council Decision amending the Annexes to the Council Decision-Recommendation on compliance with principles of good laboratory practice of 9 March 1995 (C(95)8(Final)).
To facilitate the mutual acceptance of test data generated for submission to Regulatory Authorities of the OECD member countries, harmonisation of the procedures adopted to monitor GLP compliance, as well as comparability of their quality and rigour, are essential. The aim of this part of this Annex is to provide detailed practical guidance to the Member States on the structure, mechanisms and procedures they should adopt when establishing national GLP compliance monitoring programmes so that these programmes may be internationally acceptable.
It is recognised that Member States will adopt GLP principles and establish compliance monitoring procedures according to national legal and administrative practices, and according to priorities they give to, for example the scope of initial and subsequent coverage concerning categories of chemicals and types of testing. Since Member States may establish more than one GLP Monitoring Authority due to their legal framework for chemicals control, more than one GLP compliance programme may be established. The guidance set forth in the following paragraphs concerns each of these Authorities and compliance programmes, as appropriate.
The definitions of terms in the OECD principles of good laboratory practice adopted in Article 1 of Directive 2004/10/EC of the European Parliament and of the Council are applicable to this part of this Annex. In addition, the following definitions apply:
—GLP principlesprinciples of good laboratory practice that are consistent with the OECD principles of good laboratory practice as adopted in Article 1 of Directive 2004/10/EC,
—GLP compliance monitoringthe periodic inspection of test facilities and/or auditing of studies for the purpose of verifying adherence to GLP principles,
—(national) GLP compliance programmethe particular scheme established by a Member State to monitor GLP compliance by test facilities within its territories, by means of inspections and study audits,
—(national) GLP Monitoring Authoritya body established within a Member State with responsibility for monitoring the GLP compliance of test facilities within its territories and for discharging other such functions related to GLP as may be nationally determined. It is understood that more than one such body may be established in a Member State,
—test facility inspectionan on-site examination of the test facility's procedures and practices to assess the degree of compliance with GLP principles. During inspections, the management structures and operational procedures of the test facility are examined, key technical personnel are interviewed, and the quality and integrity of data generated by the facility are assessed and reported,
—study audita comparison of raw data and associated records with the interim or final report in order to determine whether the raw data have been accurately reported, to determine whether testing was carried out in accordance with the study plan and standard operating procedures, to obtain additional information not provided in the report, and to establish whether practices were employed in the development of data that would impair their validity,
—inspectora person who performs the test facility inspections and study audits on behalf of the (national) GLP Monitoring Authority,
—GLP compliance statusthe level of adherence of a test facility to the GLP principles as assessed by the (national) GLP Monitoring Authority,
—Regulatory Authoritya national body with legal responsibility for aspects of the control of chemicals.
Administration
A (national) GLP compliance programme should be the responsibility of a properly constituted, legally identifiable body adequately staffed and working within a defined administrative framework.
Member States should:
ensure that the (national) GLP Monitoring Authority is directly responsible for an adequate ‘team’ of inspectors having the necessary technical/scientific expertise or is ultimately responsible for such a team,
publish documents relating to the adoption of GLP principles within their territories,
publish documents providing details of the (national) GLP compliance programme, including information on the legal or administrative framework within which the programme operates and references to published acts, normative documents (e.g., regulations, codes of practice), inspection manuals, guidance notes, periodicity of inspections and/or criteria for inspection schedules, etc.,
maintain records of test facilities inspected (and their GLP compliance status) and of studies audited for both national and international purposes.
(National) GLP Monitoring Authorities will have access to commercially valuable information and, on occasion, may even need to remove commercially sensitive documents from a test facility or refer to them in detail in their reports.
Member States should:
make provision for the maintenance of confidentiality, not only by Inspectors but also by any other persons who gain access to confidential information as a result of GLP compliance monitoring activities,
ensure that, unless all commercially sensitive and confidential information has been excised, reports of test facility inspections and study audits are made available only to Regulatory Authorities and, where appropriate, to the test facilities inspected or concerned with study audits and/or to study sponsors.
(National) GLP Monitoring Authorities should:
ensure that an adequate number of inspectors is available.
The number of inspectors required will depend on:
the number of test facilities involved in the (national) GLP compliance programme;
the frequency with which the GLP compliance status of the test facilities is to be assessed;
the number and complexity of the studies undertaken by those test facilities;
the number of special inspections or audits requested by Regulatory Authorities,
ensure that inspectors are adequately qualified and trained.
Inspectors should have qualifications and practical experience in the range of scientific disciplines relevant to the testing of chemicals. (National) GLP Monitoring Authorities should:
ensure that arrangements are made for the appropriate training of GLP inspectors, having regard to their individual qualifications and experience;
encourage consultations, including joint training activities where necessary, with the staff of (national) GLP Monitoring Authorities in other OECD member countries in order to promote international harmonisation in the interpretation and application of GLP principles, and in the monitoring of compliance with such principles,
ensure that inspectorate personnel, including experts under contract, have no financial or other interests in the test facilities inspected, the studies audited or the firms sponsoring such studies,
provide inspectors with a suitable means of identification (e.g., an identity card).
Inspectors may be:
on the permanent staff of the (national) GLP Monitoring Authority,
on the permanent staff of a body separate from the (national) GLP Monitoring Authority, or
employed on contract, or in another way, by the (national) GLP Monitoring Authority to perform test facility inspections or study audits.
In the latter two cases, the (national) GLP Monitoring Authority should have ultimate responsibility for determining the GLP compliance status of test facilities and the quality/acceptability of a study audit, and for taking any action based on the results of test facility inspections or study audits which may be necessary.
GLP compliance monitoring is intended to ascertain whether test facilities have implemented GLP principles for the conduct of studies and are capable of assuring that the resulting data are of adequate quality. As indicated above, Member States should publish the details of their (national) GLP compliance programmes. Such information should, inter alia:
define the scope and extent of the programme.
A (national) GLP compliance programme may cover only a limited range of chemicals, for example, industrial chemicals, pesticides, pharmaceuticals, etc., or may include all chemicals. The scope of the monitoring for compliance should be defined, both with respect to the categories of chemicals and to the types of tests subject to it, for example, physical, chemical, toxicological and/or ecotoxicological,
provide an indication as to the mechanism whereby test facilities enter the programme.
The application of GLP principles to health and environmental safety data generated for regulatory purposes may be mandatory. A mechanism should be available whereby test facilities may have their compliance with GLP principles monitored by the appropriate (national) GLP Monitoring Authority,
provide information on categories of test facility inspections/study audits.
A (national) GLP compliance programme should include:
provision for test facility inspections. These inspections include both a general test facility inspection and a study audit of one or more on-going or completed studies;
provisions for special test facility inspections/study audits at the request of a Regulatory Authority, for example, prompted by a query arising from the submission of data to a Regulatory Authority,
define the powers of inspectors for entry into test facilities and their access to data held by test facilities (including specimens, SOPs (standard operating procedures) other documentation, etc.).
While inspectors will not normally wish to enter test facilities against the will of the facility's management, circumstances may arise where test facility entry and access to data are essential to protect public health or the environment. The powers available to the (national) GLP Monitoring Authority in such cases should be defined,
describe the test facility inspection and study audit procedures for verification of GLP compliance.
The documentation should indicate the procedures which will be used to examine both the organisational processes and the conditions under which studies are planned, performed, monitored and recorded. Guidance for such procedures is available in part B of this Annex,
describe actions that may be taken as follow-up test facility inspections and study audits.
When a test facility inspection or study audit has been completed, the inspector should prepare a written report of the findings.
Member States should take action where deviations from GLP principles are found during or after a test facility inspection or study audit. The appropriate actions should be described in documents from the (national) GLP Monitoring Authority.
If a test facility inspection or study audit reveals only minor deviations from GLP principles, the facility should be required to correct such minor deviations. The inspector may need, at an appropriate time, to return to the facility to verify that corrections have been introduced.
Where no, or where only minor deviations have been found, the (national) GLP Monitoring Authority may:
issue a statement that the test facility has been inspected and found to be operating in compliance with GLP principles. The date of the inspections and, if appropriate, the categories of test inspected in the test facility at that time should be included. Such statements may be used to provide information to (national) GLP Monitoring Authorities in other OECD member countries,
and/or
provide the Regulatory Authority which requested a study audit with a detailed report of the findings.
Where serious deviations are found, the action taken by (national) GLP Monitoring Authorities will depend on the particular circumstances of each case and the legal or administrative provisions under which GLP compliance monitoring has been established within their countries. Actions which may be taken include, but are not limited to, the following:
issuance of a statement, giving details of the inadequacies or faults found which might affect the validity of studies conducted in the test facility,
issuance of a recommendation to a Regulatory Authority that a study be rejected,
suspension of test facility inspections or study audits of a test facility and, for example and where administratively possible, removal of the test facility from the (national) GLP compliance programme or from any existing list or register of test facilities subject to GLP test facility inspections,
requiring that a statement detailing the deviations be attached to specific study reports,
action through the courts, where warranted by circumstances and where legal/administrative procedures so permit.
Problems, or differences of opinion, between inspectors and test facility management will normally be resolved during the course of a test facility inspection or study audit. However, it may not always be possible for agreement to be reached. A procedure should exist whereby a test facility may make representations relating to the outcome of a test facility inspection or study audit for GLP compliance monitoring and/or relating to the action the GLP Monitoring Authority proposes to take thereon.
The purpose of this part of this Annex is to provide guidance for the conduct of test facility inspections and study audits which would be mutually acceptable to OECD member countries. It is principally concerned with test facility inspections, an activity which occupies much of the time of GLP inspectors. A test facility inspection will usually include a study audit or review as a part of the inspection, but study audits will also have to be conducted from time to time at the request, for example, of a Regulatory Authority. General guidance for the conduct of study audits will be found at the end of this Annex.
Test facility inspections are conducted to determine the degree of conformity of test facilities and studies with GLP principles and to determine the integrity of data to assure that resulting data are of adequate quality for assessment and decision-making by national Regulatory Authorities. They result in reports which describe the degree of adherence of a test facility to the GLP principles. Test facility inspections should be conducted on a regular, routine basis to establish and maintain records of the GLP compliance status of test facilities.
Further clarification of many of the points in this part of this Annex may be obtained by referring to the OECD consensus documents on GLP (on, e.g., the role and responsibilities of the study director).
The definitions of terms in the OECD principles of GLP adopted in Article 1 of Directive 2004/10/EC and in Part A of this Annex are applicable to this part of this Annex.
Inspections for compliance with GLP principles may take place in any test facility generating health or environmental safety data for regulatory purposes. Inspectors may be required to audit data relating to the physical, chemical, toxicological or ecotoxicological properties of a substance or preparation. In some cases, inspectors may need assistance from experts in particular disciplines.
The wide diversity of facilities (in terms both of physical layout and management structure), together with the variety of types of studies encountered by inspectors, means that the inspectors must use their own judgment to assess the degree and extent of compliance with GLP principles. Nevertheless, inspectors should strive for a consistent approach in evaluating whether, in the case of a particular test facility or study, an adequate level of compliance with each GLP principle has been achieved.
In the following sections, guidance is provided on the various aspects of the testing facility, including its personnel and procedures, which are likely to be examined by inspectors. In each section, there is a statement of purpose, as well as an illustrative list of specific items which could be considered during the course of a test facility inspection. These lists are not meant to be comprehensive and should not be taken as such.
Inspectors should not concern themselves with the scientific design of the study or the interpretation of the findings of studies with respect to risks for human health or the environment. These aspects are the responsibility of those Regulatory Authorities to which the data are submitted for regulatory purposes.
Test facility inspections and study audits inevitably disturb the normal work in a facility. Inspectors should therefore carry out their work in a carefully planned way and, so far as practicable, respect the wishes of the management of the test facility as to the timing of visits to certain sections of the facility.
Inspectors will, while conducting test facility inspections and study audits, have access to confidential, commercially valuable information. It is essential that they ensure that such information is seen by authorised personnel only. Their responsibilities in this respect will have been established within their (national) GLP compliance monitoring programme.
Pre-inspection
Purpose: to familiarise the inspector with the facility which is about to be inspected in respect of management structure, physical layout of buildings and range of studies.
Prior to conducting a test facility inspection or study audit, inspectors should familiarise themselves with the facility which is to be visited. Any existing information on the facility should be reviewed. This may include previous inspection reports, the layout of the facility, organisation charts, study reports, protocols and curricula vitae (CVs) of personnel. Such documents would provide information on:
the type, size and layout of the facility,
the range of studies likely to be encountered during the inspection,
the management structure of the facility.
Inspectors should note, in particular, any deficiencies from previous test facility inspections. Where no previous test facility inspections have been conducted, a pre-inspection visit can be made to obtain relevant information.
Test facilities may be informed of the date and time of inspector's arrival, the objective of their visit and the length of time they expect to be on the premises. This could allow the test facility to ensure that the appropriate personnel and documentation are available. In cases where particular documents or records are to be examined, it may be useful to identify these to the test facility in advance of the visit so that they will be immediately available during the test facility inspection.
Purpose: to inform the management and staff of the facility of the reason for the test facility inspection or study audit that is about to take place, and to identify the facility areas, study(ies) selected for audit, documents and personnel likely to be involved.
The administrative and practical details of a test facility inspection or study audit should be discussed with the management of the facility at the start of the visit. At the starting conference, inspectors should:
outline the purpose and scope of the visit,
describe the documentation which will be required for the test facility inspection, such as lists of on-going and completed studies, study plans, standard operating procedures, study reports, etc. Access to and, if necessary, arrangements for the copying of relevant documents should be agreed on at this time,
clarify or request information as to the management structure (organisation) and personnel of the facility,
request information as to the conduct of studies not subject to GLP principles in the areas of the test facility where GLP studies are being conducted,
make an initial determination as to the parts of the facility to be covered during the test facility inspection,
describe the documents and specimens that will be needed for on-going or completed study(ies) selected for study audit,
indicate that a closing conference will be held at the completion of the inspection.
Before proceeding further with a test facility inspection, it is advisable for the inspector(s) to establish contact with the facility's quality assurance (QA) unit.
As a general rule, when inspecting a facility, inspectors will find it helpful to be accompanied by a member of the QA unit.
Inspectors may wish to request that a room be set aside for examination of documents and other activities.
Purpose: to determine whether the test facility has sufficient qualified personnel, staff resources and support services for the variety and number of studies undertaken; the organisational structure is appropriate, and management has established a policy regarding training and staff health surveillance appropriate to the studies undertaken in the facility.
The management should be asked to produce certain documents, such as:
floor plans,
facility management and scientific organisation charts,
CVs of personnel involved in the type(s) of studies selected for the study audit,
list(s) of on-going and completed studies with information on the type of study, initiation/completion dates, test system, method of application of test substance and name of study director,
staff health surveillance policies,
staff job descriptions and staff training programmes and records,
an index to the facility's standard operating procedures (SOPs),
specific SOPs as related to the studies or procedures being inspected or audited,
list(s) of the study directors and sponsors associated with the study(ies) being audited.
The inspector should check, in particular:
lists of on-going and completed studies to ascertain the level of work being undertaken by the test facility,
the identity and qualifications of the study director(s), the head of the quality assurance unit and other personnel,
existence of SOPs for all relevant areas of testing.
Purpose: to determine whether the mechanisms used to assure management that studies are conducted in accordance with GLP principles are adequate.
The head of the QA unit should be asked to demonstrate the systems and methods for QA inspection and monitoring of studies, and the system for recording observations made during QA monitoring. Inspectors should check:
the qualifications of the head of QA, and of all QA staff,
that the QA unit functions independently from the staff involved in the studies,
how the QA unit schedules and conducts inspections, how it monitors identified critical phases in a study, and what resources are available for QA inspections and monitoring activities,