ANNEX II, Directive (EU) 2002/49

In forcesince 29 Jul 2021cited 2×

The values of Lden and Lnight shall be determined at the assessment positions by computation, according to the method set out in Chapter 2 and the data described in Chapter 3. Measurements may be performed according to Chapter 4.

Noise calculations shall be defined in the frequency range from 63 Hz to 8 kHz octave bands. Frequency band results shall be provided at the corresponding frequency interval.

Calculations are performed in octave bands for road traffic, railway traffic and industrial noise, except for the railway noise source sound power, which uses third octave bands. For road traffic, railway traffic and industrial noise, based on these octave band results, the A-weighted long-term average sound level for the day, evening and night period, as defined in Annex I and referred to in Article 5 of Directive 2002/49/EC, is computed by the method described in Sections 2.1.2, 2.2, 2.3, 2.4 and 2.5. For roads and railway traffic in agglomerations, the A-weighted long-term average sound level is determined by the contribution from road and railway segments therein, including major roads and major railways.

LAeq,T10lg

i1

10Leq,T,iAi10 | (2.1.1)

where

Ai denotes the A-weighting correction according to IEC 61672-1

i = frequency band index

and T is the time period corresponding to day, evening or night.

Noise parameters:

Lp | Instantaneous sound pressure level |

[dB]

(re. 2 10–5 Pa)

LAeq,LT | Global long-term sound level LAeq due to all sources and image sources at point R |

[dB]

(re. 2 10–5 Pa)

LW | ‘In situ’ sound power level of a point source (moving or steady) |

[dB]

(re. 10–12 W)

LW,i,dir | Directional ‘in situ’ sound power level for the i-th frequency band |

[dB]

(re. 10–12 W)

LW′ | Average ‘in situ’ sound power level per metre of source line |

[dB/m]

(re. 10–12 W)

Other physical parameters:

p | r.m.s. of the instantaneous sound pressure | [Pa]

p0 | Reference sound pressure = 2 10–5 Pa | [Pa]

W0 | Reference sound power = 10–12 W | [watt]

All input values affecting the emission level of a source shall be determined with at least the accuracy corresponding to an uncertainty of ± 2dB(A) in the emission level of the source (leaving all other parameters unchanged).

In the application of the method, the input data shall reflect the actual usage. In general there shall be no reliance on default input values or assumptions. Default input values and assumptions are accepted if the collection of real data is associated with disproportionately high costs.

Software used to perform the calculations shall prove compliance with the methods herewith described by means of certification of results against test cases.

The road traffic noise source shall be determined by combining the noise emission of each individual vehicle forming the traffic flow. These vehicles are grouped into five separate categories with regard to their characteristics of noise emission:

Category 1Light motor vehicles

Category 2Medium heavy vehicles

Category 3Heavy vehicles

Category 4Powered two-wheelers

Category 5Open category

In the case of powered two-wheelers, two separate subclasses are defined for mopeds and more powerful motorcycles, since they operate in very different driving modes and their numbers usually vary widely.

The first four categories shall be used, and the fifth category is optional. It is foreseen for new vehicles that may be developed in the future and may be sufficiently different in their noise emission to require an additional category to be defined. This category could cover, for example, electric or hybrid vehicles or any vehicle developed in the future substantially different from those in categories 1 to 4.

The details of the different vehicle classes are given in Table [2.2.a].

[Directive 2007/46/EC of the European Parliament and of the Council of 5 September 2007 establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles (OJ L 263, 9.10.2007, p. 1).] [Sport Utility Vehicles.] [Multi-Purpose Vehicles.]

Category | Name | Description |

Vehicle category in EC

Whole Vehicle Type Approval

1 | Light motor vehicles | Passenger cars, delivery vans ≤ 3,5 tons, SUVs, MPVs including trailers and caravans | M1 and N1

2 | Medium heavy vehicles | Medium heavy vehicles, delivery vans > 3,5 tons, buses, motorhomes, etc. with two axles and twin tyre mounting on rear axle | M2, M3 and N2, N3

3 | Heavy vehicles | Heavy duty vehicles, touring cars, buses, with three or more axles | M2 and N2 with trailer, M3 and N3

4 | Powered two-wheelers | 4a | Two-, Three- and Four-wheel Mopeds | L1, L2, L6

4b | Motorcycles with and without sidecars, Tricycles and Quadricycles | L3, L4, L5, L7

5 | Open category | To be defined according to future needs | N/A

In this model, each vehicle (category 1, 2, 3, 4 and 5) is represented by one single point source radiating uniformly. The first reflection on the road surface is treated implicitly. As depicted in Figure [2.2.a], this point source is placed 0,05 m above the road surface.

The traffic flow is represented by a source line. In the modelling of a road with multiple lanes, each lane should ideally be represented by a source line placed in the centre of each lane. However, it is also acceptable to model one source line in the middle of a two way road or one source line per carriageway in the outer lane of multi-lane roads.

The sound power of the source is defined in the ‘semi-free field’, thus the sound power includes the effect of the reflection of the ground immediately under the modelled source where there are no disturbing objects in its immediate surroundings except for the reflection on the road surface not immediately under the modelled source.

The noise emission of a traffic flow is represented by a source line characterised by its directional sound power per metre per frequency. This corresponds to the sum of the sound emission of the individual vehicles in the traffic flow, taking into account the time spent by the vehicles in the road section considered. The implementation of the individual vehicle in the flow requires the application of a traffic flow model.

If a steady traffic flow of Qm vehicles of category m per hour is assumed, with an average speed vm (in km/h), the directional sound power per metre in frequency band i of the source line LW′, eq,line,i,m is defined by:

LW′,eq,line,i,mLW,i,m10lg

Qm

1000vm

(2.2.1)

where LW,i,m is the directional sound power of a single vehicle. LW′,m is expressed in dB (re. 10–12 W/m). These sound power levels are calculated for each octave band i from 63 Hz to 8 kHz.

Traffic flow data Qm shall be expressed as yearly average per hour, per time period (day-evening-night), per vehicle class and per source line. For all categories, input traffic flow data derived from traffic counting or from traffic models shall be used.

The speed vm is a representative speed per vehicle category: in most cases the lower of the maximum legal speed for the section of road and the maximum legal speed for the vehicle category.

In the traffic flow, all vehicles of category m are assumed to drive at the same speed, i.e. vm.

A road vehicle is modelled by a set of mathematical equations representing the two main noise sources:

1.

Rolling noise due to the tyre/road interaction;

2.

Propulsion noise produced by the driveline (engine, exhaust, etc.) of the vehicle.

Aerodynamic noise is incorporated in the rolling noise source.

For light, medium and heavy motor vehicles (categories 1, 2 and 3), the total sound power corresponds to the energetic sum of the rolling and the propulsion noise. Thus, the total sound power level of the source lines m = 1, 2 or 3 is defined by:

LW,i,mvm10lg10LWR,i,mvm1010LWP,i,mvm10 | (2.2.2)

where LWR,i,m is the sound power level for rolling noise and LWP,i,m is the sound power level for propulsion noise. This is valid on all speed ranges. For speeds less than 20 km/h it shall have the same sound power level as defined by the formula for vm = 20 km/h.

For two-wheelers (category 4), only propulsion noise is considered for the source:

LW,i,m = 4(vm = 4) = LWP,i,m = 4(vm = 4) | (2.2.3)

This is valid on all speed ranges. For speeds less than 20 km/h it shall have the same sound power level as defined by the formula for vm = 20 km/h.

The source equations and coefficients are valid for the following reference conditions:

a constant vehicle speed

a flat road

an air temperature τref = 20 °C

a virtual reference road surface, consisting of an average of dense asphalt concrete 0/11 and stone mastic asphalt 0/11, between 2 and 7 years old and in a representative maintenance condition

a dry road surface

no studded tyres.

The rolling noise sound power level in the frequency band i for a vehicle of class m = 1,2 or 3 is defined as:

LWR,i,mAR,i,mBR,i,mlg

vm

vref

ΔLWR,i,m | (2.2.4)

The coefficients AR,i,m and BR,i,m are given in octave bands for each vehicle category and for a reference speed vref = 70 km/h. ΔLWR,i,m corresponds to the sum of the correction coefficients to be applied to the rolling noise emission for specific road or vehicle conditions deviating from the reference conditions:

ΔLWR,i,m = ΔLWR,road,i,m + ΔLstuddedtyres,i,m + ΔLWR,acc,i,m + ΔLW,temp | (2.2.5)

ΔLWR,road,i,m accounts for the effect on rolling noise of a road surface with acoustic properties different from those of the virtual reference surface as defined in Chapter 2.2.2. It includes both the effect on propagation and on generation.

ΔLstudded tyres,i,m is a correction coefficient accounting for the higher rolling noise of light vehicles equipped with studded tyres.

ΔLWR,acc,i,m accounts for the effect on rolling noise of a crossing with traffic lights or a roundabout. It integrates the effect on noise of the speed variation.

ΔLW,temp is a correction term for an average temperature τ different from the reference temperature τref = 20 °C.

In situations where a significant number of light vehicles in the traffic flow use studded tyres during several months every year, the induced effect on rolling noise shall be taken into account. For each vehicle of category m = 1 equipped with studded tyres, a speed-dependent increase in rolling noise emission is evaluated by:

Δstud,i(v) = | ai + bi × lg(50/70) for v < 50 km/h | (2.2.6)

ai + bi × lg(v/70) for 50 ≤ v ≤ 90 km/h

ai + bi × lg(90/70) for v > 90 km/h

where coefficients ai and bi are given for each octave band.

The increase in rolling noise emission shall only be attributed according to the proportion of light vehicles with studded tyres and during a limited period Ts (in months) over the year. If Qstud,ratio is the average ratio of the total volume of light vehicles per hour equipped with studded tyres during the period Ts (in months), then the yearly average proportion of vehicles equipped with studded tyres ps is expressed by:

psQstud,ratio

Ts

12 | (2.2.7)

The resulting correction to be applied to the rolling sound power emission due to the use of studded tyres for vehicles of category m = 1 in frequency band i shall be:

ΔLstuddedtyres,i,m110lg1psps 10

Δstud,i,m1

10 | (2.2.8)

For vehicles of all other categories no correction shall be applied:

ΔLstuddedtyres,i,m ≠ 1 = 0 | (2.2.9)

The air temperature affects rolling noise emission; the rolling sound power level decreases when the air temperature increases. This effect is introduced in the road surface correction. Road surface corrections are usually evaluated at an air temperature of τref = 20 °C. In the case of a different yearly average air temperature °C, the road surface noise shall be corrected by:

ΔLW,temp,m(τ) = Km × (τref – τ) | (2.2.10)

The correction term is positive (i.e. noise increases) for temperatures lower than 20 °C and negative (i.e. noise decreases) for higher temperatures. The coefficient K depends on the road surface and the tyre characteristics and in general exhibits some frequency dependence. A generic coefficient Km = 1 = 0,08 dB/°C for light vehicles (category 1) and Km = 2 = Km = 3 = 0,04 dB/°C for heavy vehicles (categories 2 and 3) shall be applied for all road surfaces. The correction coefficient shall be applied equally on all octave bands from 63 to 8000 Hz.

The propulsion noise emission includes all contributions from engine, exhaust, gears, air intake, etc. The propulsion noise sound power level in the frequency band i for a vehicle of class m is defined as:

LWP,i,mAP,i,mBP,i,m

vmvref

vref

ΔLWP,i,m | (2.2.11)

The coefficients AP,i,m and BP,i,m are given in octave bands for each vehicle category and for a reference speed vref = 70 km/h.

ΔLWP,i,m corresponds to the sum of the correction coefficients to be applied to the propulsion noise emission for specific driving conditions or regional conditions deviating from the reference conditions:

ΔLWP,i,m = ΔLWP,road,i,m + ΔLWP,grad,i,m + ΔLWP,acc,i,m | (2.2.12)

ΔLWP,road,i,m accounts for the effect of the road surface on the propulsion noise via absorption. The calculation shall be performed according to Chapter 2.2.6.

ΔLWP,acc,i,m and ΔLWP,grad,i,m account for the effect of road gradients and of vehicle acceleration and deceleration at intersections. They shall be calculated according to Chapters 2.2.4 and 2.2.5 respectively.

The road gradient has two effects on the noise emission of the vehicle: first, it affects the vehicle speed and thus the rolling and propulsion noise emission of the vehicle; second, it affects both the engine load and the engine speed via the choice of gear and thus the propulsion noise emission of the vehicle. Only the effect on the propulsion noise is considered in this section, where a steady speed is assumed.

The effect of the road gradient on the propulsion noise is taken into account by a correction term ΔLWP,grad,m which is a function of the slope s (in %), the vehicle speed vm (in km/h) and the vehicle class m. In the case of a bi-directional traffic flow, it is necessary to split the flow into two components and correct half for uphill and half for downhill. The correction term is attributed to all octave bands equally:

For m = 1

ΔLWP,grad,i,m = 1(vm) = | Min12 ;s61 % | for s < – 6 % | (2.2.13)

0 | for – 6 % ≤ s ≤ 2 %

Min12 ;s21,5

vm

100 | for s > 2 %

For m = 2

ΔLWP,grad,i,m = 2(vm) = | Min12 ;s40,7vm20100 | for s < – 4 % | (2.2.14)

0 | for – 4 % ≤ s ≤ 0 %

Min 12 ;s

1

vm

100 | for s > 0 %

For m = 3

ΔLWP,grad,i,m = 3(vm) = | Min12 ;s40,5vm10100 | for s < – 4 % | (2.2.15)

0 | for – 4 % ≤ s ≤ 0 %

Min 12 ;s

0,8

vm

100 | for s > 0 %

For m = 4

ΔLWP,grad,i,m = 4 = 0 | (2.2.16)

The correction ΔLWP,grad,m implicitly includes the effect of slope on speed.

Before and after crossings with traffic lights and roundabouts a correction shall be applied for the effect of acceleration and deceleration as described below.

The correction terms for rolling noise, ΔLWR,acc,m,k, and for propulsion noise, ΔLWP,acc,m,k, are linear functions of the distance x (in m) of the point source to the nearest intersection of the respective source line with another source line. They are attributed to all octave bands equally:

ΔLWR,acc,m,kCR,m,kMax1

x

100 ;0 | (2.2.17)

ΔLWP,acc,m,kCP,m,kMax1

x

100 ;0 | (2.2.18)

The coefficients CR,m,k and CP,m,k depend on the kind of junction k (k = 1 for a crossing with traffic lights; k = 2 for a roundabout) and are given for each vehicle category. The correction includes the effect of change in speed when approaching or moving away from a crossing or a roundabout.

Note that at a distance |x| ≥ 100 m, ΔLWR,acc,m,k = ΔLWP,acc,m,k = 0.

For road surfaces with acoustic properties different from those of the reference surface, a spectral correction term for both rolling noise and propulsion noise shall be applied.

The road surface correction term for the rolling noise emission is given by:

ΔLWR,road,i,mαi,mβmlg

vm

vref

(2.2.19)

where

αi,m is the spectral correction in dB at reference speed vref for category m (1, 2 or 3) and spectral band i.

βm is the speed effect on the rolling noise reduction for category m (1, 2 or 3) and is identical for all frequency bands.

The road surface correction term for the propulsion noise emission is given by:

ΔLWP,road,i,m = min{αi,m;0} | (2.2.20)

Absorbing surfaces decrease the propulsion noise, while non-absorbing surfaces do not increase it.

The noise characteristics of road surfaces vary with age and the level of maintenance, with a tendency to become louder over time. In this method the road surface parameters are derived to be representative for the acoustic performance of the road surface type averaged over its representative lifetime and assuming proper maintenance.

For the purposes of this noise calculation method, a vehicle is defined as any single railway sub-unit of a train (typically a locomotive, a self-propelled coach, a hauled coach or a freight wagon) that can be moved independently and can be detached from the rest of the train. Some specific circumstances may occur for sub-units of a train that are a part of a non-detachable set, e.g. share one bogie between them. For the purpose of this calculation method, all these sub-units are grouped into a single vehicle.

For the purpose of this calculation method, a train consists of a series of coupled vehicles.

Table [2.3.a] defines a common language to describe the vehicle types included in the source database. It presents the relevant descriptors to be used to classify the vehicles in full. These descriptors correspond to properties of the vehicle, which affect the acoustic directional sound power per metre length of the equivalent source line modelled.

The number of vehicles for each type shall be determined on each of the track sections for each of the time periods to be used in the noise calculation. It shall be expressed as an average number of vehicles per hour, which is obtained by dividing the total number of vehicles travelling in a given time period by the duration in hours of this time period (e.g. 24 vehicles in 4 hours means 6 vehicles per hour). All vehicle types travelling on each track section shall be used.

Digit | 1 | 2 | 3 | 4

Descriptor | Vehicle type | Number of axles per vehicle | Brake type | Wheel measure

Explanation of the descriptor | A letter that describes the type | The actual number of axles | A letter that describes the brake type | A letter that describes the noise reduction measure type

Possible descriptors |

h

high speed vehicle (> 200 km/h)

1 |

c

cast-iron block

n

no measure

m

self-propelled passenger coaches

2 |

k

composite or sinter metal block

d

dampers

p

hauled passenger coaches

3 |

n

non-tread braked, like disc, drum, magnetic

s

screens

c

city tram or light metro self-propelled and non-self-propelled coach

4 | |

o

other

d

diesel loco

etc. | |

e

electric loco

a

any generic freight vehicle

o

other (i.e. maintenance vehicles etc.)

The existing tracks may differ because there are several elements contributing to and characterising their acoustic properties. The track types used in this method are listed in Table [2.3.b] below. Some of the elements have a large influence on acoustic properties, while others have only secondary effects. In general, the most relevant elements influencing the railway noise emission are: railhead roughness, rail pad stiffness, track base, rail joints and radius of curvature of the track. Alternatively, the overall track properties can be defined and, in this case, the railhead roughness and the track decay rate according to ISO 3095 are the two acoustically essential parameters, plus the radius of curvature of the track.

A track section is defined as a part of a single track, on a railway line or station or depot, on which the track's physical properties and basic components do not change.

Table [2.3.b] defines a common language to describe the track types included in the source database.

Digit | 1 | 2 | 3 | 4 | 5 | 6

Descriptor | Track base | Railhead Roughness | Rail pad type | Additional measures | Rail joints | Curvature

Explanation of the descriptor | Type of track base | Indicator for roughness | Represents an indication of the ‘dynamic’ stiffness | A letter describing acoustic device | Presence of joints and spacing | Indicate the radius of curvature in m

Codes allowed |

B

Ballast

E

Well maintained and very smooth

S

Soft

(150-250 MN/m)

N

None

N

None

N

Straight track

S

Slab track

M

Normally maintained

M

Medium

(250 to 800 MN/m)

D

Rail damper

S

Single joint or switch

L

Low

(1000-500 m)

L

Ballasted bridge

N

Not well maintained

H

Hard (800-1000MN/m)

B

Low barrier

D

Two joints or switches per 100 m

M

Medium

(Less than 500 m and more than 300 m)

N

Non-ballasted bridge

B

Not maintained and bad condition

A

Absorber plate on slab track

M

More than two joints or switches per 100 m

H

High

(Less than 300 m)

T

Embedded track

E

Embedded rail

O

Other

O

Other

The different equivalent noise line sources are placed at different heights and at the centre of the track. All heights are referred to the plane tangent to the two upper surfaces of the two rails.

The equivalent sources include different physical sources (index p). These physical sources are divided into different categories depending on the generation mechanism, and are: (1) rolling noise (including not only rail and track base vibration and wheel vibration but also, where present, superstructure noise of the freight vehicles); (2) traction noise; (3) aerodynamic noise; (4) impact noise (from crossings, switches and junctions); (5) squeal noise and (6) noise due to additional effects such as bridges and viaducts.

(1)

The roughness of wheels and railheads, through three transmission paths to the radiating surfaces (rails, wheels and superstructure), constitutes the rolling noise. This is allocated to h = 0,5 m (radiating surfaces A) to represent the track contribution, including the effects of the surface of the tracks, especially slab tracks (in accordance with the propagation part), to represent the wheel contribution and to represent the contribution of the superstructure of the vehicle to noise (in freight trains).

This article is long: the rest is at the official publication.