ANNEX III ATTESTATION OF CONFORMITY, Decision_act (EU) 1998/213

In forcesince 21 Apr 2012

for kits having more than one of the intended uses specified in the following families, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative.

For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant guideline for European technical approval:

[Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material).] [System 1: See Annex III(2)(i) to Directive 89/106/EEC, without audit-testing of samples.] [Products/materials not covered by footnote (1).] [System 3: See Annex III(2)(ii) to Directive 89/106/EEC, second possibility.] [System 4: See Annex III(2)(ii) to Directive 89/106/EEC, third possibility.] [Products/materials that do not require to be tested for reaction to fire (e.g. Products/materials of Classes A1 according to Commission Decision 96/603/EC).]

Product(s) | Intended use(s) |

Level(s) or class(es)

(reaction to fire)

Attestation of conformity system(s)

Internal partition kits | For uses subject to reaction to fire requirements | A1, A2, B, C | 1

A1, A2, B, C, D, E | 3

(A1 to E), F | 4

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement of all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant guideline for European technical approval:

[System 3: See Annex III(2)(ii) to Directive 89/106/EEC, second possibility.]

Product(s) | Intended use(s) |

Level(s) or class(es)

(fire resistance)

Attestation of conformity system(s)

Internal partition kits | For fire compartmentation | any | 3

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement of all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant Guideline for European Technical Approvals:

[In particular, those dangerous substances defined in Council Directive 76/769/EEC, as amended.] [System 3: See Annex III(2)(ii) to Directive 89/106/EEC, second possibility.]

Product(s) | Intended use(s) | Level(s) or class(es) | Attestation of conformity system(s)

Internal partition kits | For uses subject to regulations on dangerous substances | — | 3

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement of all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant Guideline for European Technical Approvals:

[System 3: See Annex III(2)(ii) to Directive 89/106/EEC, second possibility.]

Product(s) | Intended use(s) | Level(s) or class(es) | Attestation of conformity system(s)

Internal partition kits | For uses liable to present ‘safety-in-use’ risks and subject to such regulations | — | 3

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

For the product(s) and intended use(s) listed below, EOTA is requested to specify the following system(s) of attestation of conformity in the relevant Guideline for European Technical approvals:

[System 4: See Annex III(2)(ii) to Directive 89/106/EEC, third possibility.]

Product(s) | Intended use(s) | Level(s) or class(es) | Attestation of conformity system(s)

Internal partition kits | For uses other than those mentioned in 1/5, 2/5, 3/5 and 4/5 | — | 4

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, point 1.2.3 of the interpretative documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.