1.1. The approval authority of a Contracting Party must verify, before granting type-approval, the existence of satisfactory arrangements and procedures for ensuring effective control so that vehicles, equipment or parts when in production conform to the approved typeThe European Community and the Member States shall be involved as Contracting Parties to the Revised Agreement in accordance with the following rules.
1.2. The requirement in paragraph 1.1 must be verfied Negotiations and preparatory work with regard to the satisfaction of the authority granting type-approval but may also be verified, on behalf and at the request of the authority granting type-approval, by the approval authority of another Contracting Party. In that case, the latter approval authority prepares a statement of compliance outlining the areas and production facilities it has covered as relevant to the produce(s) to be type-approved.
1.3. The approval authority must also accept the manufacturer's registration to Harmonized Standard ISO 9002 (the scope of which covers the produces) to be approved) or an equivalent accreditation standard as satisfying the requirements of paragraph 1.1. The manufacturer must provide details of the registration and undertake to inform the approval authoritiy of any revisions to its validity or scope.
1.4. On receiving an application from the authority of another Contracting Party the approval authority shall send forthwith the statement of compliance mentionedUN/ECE work programme and to work preceding the adoption of Regulations or amendments to existing Regulations to which the Community accedes
The contribution of the Union with regard to the priorities of the work programme shall be established as appropriate in accordance with the procedure laid down in Articles 218(3) and (4) TFEU in conjunction with Article 207(2) TFEU.
Representatives of the Commission and Member States shall participate in the preparatory work of expert groups with the objective of facilitating the adoption of a proposal for a new UN/ECE Regulation or amending an existing UN/ECE Regulation. In the course of this preparatory work, Member State experts may advance technical opinions and may participate fully in the last sentence of paragraph 1.2 or advise that it is not in a position to provide such a statement.
2.1. Every vehicle, equipment or part approved pursuant to Regulation annexed to this Agreement must be so manufactured as to conform to the type approved by meeting the requirements of this Appendix and of the said Regulation.
2.2. The approval authority of a Contracting Party granting a type-approval pursuant to a technical discussions only on the basis of their technical expertise without binding their national authorities or the Community.
Following this preparatory phase, the Commission shall represent the Union in the Administrative Committee as set up by Article 1 of the Revised Agreement as spokesman for the Union, in conformity with Article 207 TFEU. The Community’s definitive position on the adoption of a new UN/ECE Regulation annexed to this Agreement must verify the existence of adequate arrangements and documented control plans, to be agreed with the manufacturer for each approval, to carry out at specified intervals those tests or associated checks necessary to verify continued conformity or the amendment of an existing UN/ECE Regulation shall be decided in accordance with the approved type, including, specifically, where applicable, tests specified in the said Regulation.
2.3. The holder of the approval must in particular:
2.3.1. ensure the existence of procedures for effective control of the conformity of products (vehicles, equipment or parts)Article 4 (2) of this Decision.
At all stages of this procedure, the Commission shall inform the European Parliament, particularly with regard to the type-approval;
2.3.2. have access to the testing equipment necessary for checking the conformity to each approved type;
2.3.3. ensure that test results' data are recorded and that annexed documents remain available for a period to be determined in agreement with the approval authority. This period must not exceed 10 years;
2.3.4. analyse results of each type of test, in order to verify and ensure the stability of the product characteristics, making allowance for variation of an industrial production;
2.3.5. ensure that for each type of product, at least the checks prescribed in this Appendix and the tests prescribed in the applicable Regulations are carried out;
2.3.6. ensure that any set of samples or test pieces giving evidence of non-conformity in the type of test in question gives rise to a further sampling and test. All the necessary steps must be taken to restore conformity of the corresponding production.
2.4. The authority which has granted type-approval may at any time verify the conformity control methods applied in each production facility. The normal frequency of these verfications must be consistent with the arrangements (if any) accepted pursuant to paragraph 1.2 or 1.3 of this Appendix and be such as to ensure that the relevant controls are reviewed over a period consistent with the climate of trust established by the approval authority.
2.4.1. At very inspection, the test records and production records must be availabledrawing up of the work programme and to the direction and results of preparatory work. The Commission shall in addition forward draft UN/ECE Regulations and amendments to the Parliament in good time.
2. Adoption of the UN/ECE Regulations and of amendments to such existing Regulations
The Commission shall exercise the right to vote for the Community within the bodies set up pursuant to the Revised Agreement. The Member States shall not vote except in cases where it has been decided that the Community is not, or will not be, bound by a UN/ECE Regulation.
The Community institutions shall undertake to speed up their procedures as far as possible in order not to delay the vote within the ECE unnecessarily. For this purpose the Commission shall submit its proposal as soon as all of the essential components of the draft UN/ECE Regulation have been supplied.
3. Amendments to the Revised Agreement
Only the Community may put forward amendments to the visiting inspector.
2.4.2. Where the nature of the test is appropriate, the inspector may select samples at random to be tested in the manufacturer's laboratory (or by the Technical Service where the Regulation annexed to this Agreement so provides). The minimum number of samples may be determined according to the results of the manufacturer's own verification.
2.4.3. Where the level of control appears unsatisfactory, or when it seems necessary to verify the validity of the tests carried out in application of paragraph 2.4.2, the inspector must select samples to be sent to the Technical Service which conducts the type-approval tests.
2.4.4. The approval authority may carry out any check or test prescribed Revised Agreement.
The Member States shall align their position with that expressed by the Community with regard to the amendments tabled by other Contracting Parties in accordance with Article 13 of the Revised Agreement.
4. Should a Member State become involved in a dispute settlement procedure within the meaning of Article 10 of the Revised Agreement, the position of the Member State on points of interpretation of the Agreement in this Appendix or in the applicable Regulation annexed to this Agreement.
2.4.5. In cases where unsatisfactory results are found during an inspection, the approval authority must ensure that all necessary steps are taken to restore conformity of production as rapidly as possibleprocedure shall be coordinated with the Commission after consultation with the other Member States.