ANNEX III PRODUCT FAMILY STRUCTURAL TIMBER PRODUCTS (1/3), Decision_act (EU) 1997/176

In forcesince 2 Aug 2001

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, CEN/Cenelec (European Committee for Standardization/European Committee for Electrotechnical Standardization) are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):

Product(s) | Intended use(s) | Level(s) or class(es) of reaction to fire | Attestation of conformity system(s)

Products of this column can be treated against fire, biological attack, or not treated. | Bridges, railtracks and buildings | A1 (1), A2 (1), B (1), C (1) | 1 (4)

Solid structural timber products |

A1 (2), A2 (2), B (2), C (2), D, E,

(A1 to E) (3), F

| 2 + (5)

Elements

Bridge elements, truss elements, sleepers, floor elements, wall elements, roof elements such as beams, arches, joists, rafters, columns, poles, piles.

Kits

Trusses, floors, walls, roofs, frames.

Timber poles | Overhead lines. | 2+ (5)

(1)

Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material) .

(2)

Products/materials not covered by footnote 1 .

(3)

Products/materials that do not require to be tested for reaction to fire (e.g. Products/materials of Classes A1 according to Commission Decision 96/603/EC).

(4)

System 1: see Annex III, point 2 (i) to Directive 89/106/EEC, without audit-testing of samples.

(5)

System 2 +: see Annex III, point 2 (ii), first possibility, of Directive 89/106/EEC including certification of the factory production control by an approved body on the basis of initial inspections of factory and of factory production control as well as of continuous surveillance assessment and approval of factory production control

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristics, see Article 2 (1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the interpretative documents. In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY

STRUCTURAL TIMBER PRODUCTS (2/3)

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, CEN/Cenelec (European Committee for Standardization/European Committee for Electrotechnical Standardization) are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):

Product(s) | Intended use(s) | Level(s) or class(es) of reaction to fire | Attestation of conformity system(s)

Products of this column can be treated against fire, biological attack, or not treated. | bridges and buildings | 1 (1)

Structural glued laminated products and other glued timber products

Elements

Bridge elements, truss elements, floor elements, wall elements, roof elements such as beams, arches, joists, rafters, columns, poles, piles.

Kits

Trusses, floors, walls, roofs, frames.

(1)

System 1: see Annex III, point 2 (i) to Directive 89/106/EEC, without audit-testing of samples.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic, see Article 2 (1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the interpretative documents. In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY

STRUCTURAL TIMBER PRODUCTS (3/3)

Systems of attestation of conformity

For the product(s) and intended use(s) listed below, CEN/Cenelec (European Committee for Standardization/European Committee for Electrotechnical Standardization) are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):

Product(s) | Intended use(s) | Level(s) or class(es) of reaction to fire | Attestation of conformity system(s)

Products of this column can be treated against fire, biological attack, or not treated. | Structural timber products | 3 (1)

Fasteners for structural timber products

Connectors for timber, split ring connectors, cylindrical steel and wood dowels, wood screws, threaded bolts, wood nails.

(1)

System 3: see Annex III, point 2 (ii) to Directive 89/106/EEC, second possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic, see Article 2 (1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the interpretative documents. In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

( 1 ) OJ No L 40, 11. 2. 1989, p. 12.

( 2 ) OJ No L 220, 30. 8. 1993, p. 1.