For the product(s) and intended use(s) listed below, European Committee for Standardization, European Committee for Electrotechnical Standardization (CEN/Cenelec) are requested to speciy the following system(s) of attestation of conformity in the relevant harmonized standard(s):
[For reaction to fire, see Commission Decision 2000/147/EC (OJ L 50, 23.2.2000, p. 14).] [System 2 +: See Directive on construction products (CPD) Annex III.2.(ii), first possibility, including certification of the factory production control by an approved body on the basis of its continuous surveillance, assessment and approval.] [System 4: CPD Annex III.2.(ii), third possibility.]
System 1: See Directive 89/106/EEC, Annex III(2)(i), without audit-testing of samples.
System 3: See Directive 89/106/EEC, Annex III(2)(ii), second possibility.
System 4: See Directive 89/106/EEC, Annex III(2)(ii), third possibility.
[Products/materials for which a clearly identifiable stage in the production process results in an improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material).] [Products/materials not covered by footnote *.] [Products/materials that do not require to be tested for reaction to fire (e.g. Products/materials of Class A1 according to Commission Decision 96/603/EC, OJ L 267, 19.10.1996, p. 23).]
Product(s) | Intended use(s) |
Level(s) or class(es)
(Reaction to fire)
Attestation of conformity system(s)
Prefabricated chimneys (storey height elements), flue liners (elements or blocks), multi-shell chimney (elements or blocks), single walled chimneys blocks, kits of free standing chimneys and attached chimneys | Chimneys | Any | 2 +
Chimney terminals | Chimneys | Any | 4
Prefabricated chimneys (storey height elements), flue liners (elements or blocks), multi-shell chimney (elements or blocks), single walled chimneys blocks, kits of free standing chimneys and attached chimneys, chimney terminals | For uses subject to regulations on reaction to fire | (A1, A2, B, C) | 1
(A1, A2, B, C), D, E | 3
(A1 to E), F | 4
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
[For reaction to fire, see Commission Decision 2000/147/EC (OJ L 50, 23.2.2000, p. 14).] [Products/materials for which a clearly identifiable stage in the production process results in any improvement of the reaction to fire classification (e.g. an addition of fire retardants or a limiting of organic material).] [Products/materials not covered by footnote (2).] [System 1: See CPD Annex III.2.(i), without audit-testing of samples.] [System 3: See CPD Annex III.2.(ii), Second possibility.] [System 4: See CPD Annex III.2.(ii), third possibility.] [Products/materials that do not require to be tested for reaction to fire (e.g. Products/materials of Classes A1 according to Commission Decision 96/603/EC).]
Product(s) | Intended use(s) |
Level(s) or class(es)
(Reaction to fire of incorporated materials)
Attestation of conformity system(s)
Plasterboards and ceiling elements with thin laminations, fibrous gypsum boards,fibrous gypsum plaster casts and composite panels (laminates) in which the incorporated material is placed on a face susceptible to be exposed to fire, including relevant ancillary products | In walls, partitions or ceilings (or lining thereof) subject to reaction to fire requirements |
A1, A2, B, C
A1, A2, B, C, D, E
(A1 to E), F
1
3
4
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
[System 3: See CPD, Annex III.2.(ii), second possibility.]
Product(s) | Intended use(s) |
Level(s) or class(es)
(Resistance to fire)
Attestation of conformity system(s)
Plasterboards, blocks, ceiling elements and gypsum plasters,fibrous gypsum plaster casts, including relevant ancillary products | In walls, partitions or ceilings, as relevant, intended for fire protection of structural elements and/or fire compartmentation in buildings | Any | 3
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
[System 3: See CPD Annex III.2.(ii), second possibility.]
Product(s) | Intended use(s) | Level(s) or class(es) | Attestation of conformity system(s)
Plasterboards, including relevant ancillary products | For stiffening timber-framed windloadbearing walls or timber roof struss structures | — | 3
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
For the product(s) and intended use(s) listed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
[System 4: See CPD Annex III.2.(ii), third possibility.]
Product(s) | Intended use(s) | Level(s) or class(es) | Attestation of conformity system(s)
Plasterboards, blocks, ceiling elements and plasters,fibrous gypsum plaster casts, including relevant ancillary products | In walls, partitions or ceilings, as relevant, for situations and uses not mentioned in (1/4), (2/4) or (3/4) | — | 4
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2.1 of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
For the product(s) and intended use(s) listsed below, CEN/Cenelec are requested to specify the following system(s) of attestation of conformity in the relevant harmonized standard(s):
[‘Critical’ in the sense that those requirements may, in case of failure of the bearing, put the works or parts thereof in states beyond those regarded as serviceability and ultimate limit states.] [‘Not critical’ in the sense that those requirements may not, in case of failure of the bearing and under normal circumstances, put the works or parts thereof in states beyond those regarded as serviceability and ultimate limit states.] [System 1: See CPD Annex III.2.(i), without audit-testing of samples.] [System 3: See CPD Annex III.2.(ii), second possibility.]
Product(s) | Intended use(s) | Level(s) or class(es) | Attestation of conformity system(s)
Structural bearings | In buildings and civil engineering works where requirements on individual bearings are critical | | 1
In buildings and civil engineering works where requirements on individual bearings are not critical | | 3
The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2 (1) of the CPD and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.