DEFINITIONS
For the purposes of this Directive:
1.1. 'Vehicle type with regard to the installation of lighting and light-signalling devices`
means vehicles which do not differ in the essential respects mentioned in items 1.1.1 to 1.1.4.
The following are likewise considered not to be 'vehicles of a different type`: vehicles which differ within the meaning of items 1.1.1 to 1.1.4, but not in such a way as to entail a change in the kind, number, positioning and geometric visibility of the lamps and the inclination of the dipped beam prescribed for the vehicle type in question, and vehicles on which optional lamps are fitted or are absent;
1.1.1. the dimensions and the external shape of the vehicle;
1.1.2. the number and positioning of the devices;
1.1.3. the headlamp-levelling system;
1.1.4. the suspension system.
1.2. 'Transverse plane`
means a vertical plane perpendicular to the median longitudinal plane of the vehicle.
1.3. 'Unladen vehicle`
means the vehicle in running order, as defined in item 2.6 of Annex I, model information document, to Directive 70/156/EEC, but without driver.
1.4. 'Laden vehicle`
means the vehicle loaded to its technically permissible maximum mass, as stated by the manufacturer, who shall also fix the distribution of this mass between the axles in accordance with the method described in Appendix 1.
1.5. 'Device`
means an element or an assembly of elements used to perform one or more functions.
1.6. 'Light source with regard to filament lamps`
means the filament itself. (Where a lamp has several filaments, each one shall constitute a light source).
1.7. 'Lamp`
means a device designed to illuminate the road or to emit a light signal. Rear registration plate lamps and retro reflectors are likewise regarded as lamps.
1.7.1. 'Equivalent lamps`
means lamps having the same function and authorized in the country in which the vehicle is registered; such lamps may have different characteristics from those installed on the vehicle when it is approved on condition that they satisfy the requirements of this Annex.
1.7.2. 'Single-function lamp`
means a part of a device which performs a single lighting or light-signalling function.
1.7.3. 'Independent lamps` (1)
means devices having separate illuminating surfaces, separate light sources and separate lamp bodies.
(;) In the case of lighting devices for the rear number plate and the direction indicators (category 5), replace 'illuminating surface` by 'light-emitting surface` in the absence of an illuminating surface.
1.7.4. 'Grouped lamps` (¹)
means devices having separate illuminating surfaces and separate light sources, but a common lamp body.
1.7.5. 'Combined lamps` (¹)
means devices having separate illuminating surfaces, but a common light source and a common lamp body.
1.7.6. 'Reciprocally incorporated lamps` (¹)
Means devices having separate light sources or a single light source operating under different conditions (e.g. optical, mechanical or electrical differences), totally or partially common illuminating surfaces and a common lamp body.
1.7.7. 'Concealable lamp`
means a lamp capable of being partly or completely hidden when not in use. This result may be achieved by means of a movable cover, by displacement of the lamp or by any other suitable means. The term 'retractable` is used more particularly to describe a concealable lamp, the displacement of which enables it to be inserted within the bodywork.
1.7.8. 'Main-beam headlamp`
means the lamp used to illuminate the road over a long distance ahead of the vehicle.
1.7.9. 'Dipped-beam headlamp`
means the lamp used to illuminate the road ahead of the vehicle without causing undue dazzle or discomfort to oncoming drivers and other road-users.
1.7.10. 'Front fog lamp`
means the lamp used to improve the illumination of the road in case of fog, snowfall, rainstorms or dust clouds.
1.7.11. 'Reversing lamp`
means the lamp used to illuminate the road to the rear of the vehicle and to warn other road-users that the vehicle is reversing or about to reverse.
1.7.12. 'Direction indicator lamp`
means the lamp used to indicate to other road-users that the driver intends to change direction to the right or to the left.
1.7.13. 'Hazard warning signal`
means the simultaneous operation of all of a vehicle's direction indicator lamps to draw attention to the fact that the vehicle temporarily constitutes a special danger to other road-users.
1.7.14. 'Stop lamp`
means the lamp used to indicate to other road-users to the rear of the vehicle that the latter's driver is applying the service brake.
1.7.15. 'Rear registration plate lamp`
means the device used to illuminate the space intended to accommodate the rear registration plate; it may consist of different optical elements.
1.7.16. 'Front position lamp`
means the lamp used to indicate the presence and the width of the vehicle when viewed from the front.
1.7.17. 'Rear position lamp`
means the lamp used to indicate the presence and the width of the vehicle when viewed from the rear.
1.7.18. 'Rear fog lamp`
means the lamp used to render the vehicle more readily visible from the rear in dense fog.
(;) In the case of lighting devices for the rear number plate and the direction indicators (category 5), replace 'illuminating surface` by 'light-emitting surface` in the absence of an illuminating surface.
1.7.19. 'Parking lamp`
means the lamp used to draw attention to the presence of a stationary vehicle in a built-up area. In such circumstances it replaces the front and rear position lamps.
1.7.20. 'End-outline marker lamp`
means the lamp fitted to the extreme outer edge as close as possible to the top of the vehicle and intended clearly to indicate the vehicle's overall width. This lamp is intended, for certain vehicles and trailers, to complement the vehicle's front and rear position lamps by drawing particular attention to its bulk.
1.7.21. 'Side-marker lamp`
means a lamp used to indicate the presence of the vehicle when viewed from the side.
1.7.22. 'Retro reflector`
means a device used to indicate the presence of a vehicle by the reflection of light emanating from a light source not connected to the vehicle, the observer being situated near the source.
For the purposes of this Directive the following are not considered as retro reflectors:
retro-reflecting number plates,
the retro-reflecting signals mentioned in the ADR (European Agreement concerning the international carriage of dangerous goods by road),
other retro-reflecting plates and signals which must be used to comply with a Member State's specifications for use as regards certain categories of vehicles or certain modes of operation.
1.8. 'Light-emitting surface`
means all or part of the exterior surface of the translucent material which helps to confer on the light its particular photometric and colorimetric properties. When only part of the exterior surface emits light, the light-emitting surface shall, in case of doubt, be specified by the competent authority after consultation with the vehicle and/or component manufacturer.
1.9. Illuminating surfaces
1.9.1. 'Illuminating surface of a lighting device` (Item 1.7.8 to 1.7.11)
means the orthogonal projection of the full aperture of the reflector in a transverse plane. If the lighting device has no reflector, the definition of item 1.9.2 shall be applied. If the light-emitting surface of the lamp extends over a part only of the full aperture of the reflector, then the projection of that part only is taken into account.
In the case of a dipped-beam headlamp, the illuminating surface is limited by the apparent trace of the cut-off on to the lens. If the reflector and lens are adjustable relative to one another, the mean adjustment should be used.
1.9.2. 'Illuminating surface of a signalling lamp other than a retro reflector` (Items 1.7.12 to 1.7.21)
means the orthogonal projection of the lamp in a plane perpendicular to its axis of reference and in contact with the exterior light-emitting surface of the lamp, this projection being bounded by the edges of the screens situated in this plane, each allowing only 98 % of the total luminous intensity of the light to persist in the direction of the axis of reference.
To determine the lower, upper and lateral limits of the illuminating surface, only screens with horizontal or vertical edges shall be used.
1.9.3. 'Illuminating surface of a retro reflector` (Items 1.7.22)
means the illuminating surface of a retro reflector in a plane perpendicular to the axis of reference and bounded by planes touching the outer edges of the light projection surface of the retro reflector and parallel to this axis. To determine the lower, upper and lateral limits of the illuminating surface, only vertical and horizontal planes shall be used.
1.10. 'Apparent surface`
for a defined direction of observation, means the orthogonal projection of the light-emitting surface in a plane perpendicular to the direction of observation (see drawing in Appendix 2) and tangential to the most exterior point of the lens.
1.11. 'Axis of reference`
means the characteristic axis of the light signal, determined by the manufacturer for use as the direction of reference (H = 0o, V = 0o) for angles of field for photometric measurements and when fitting the lamp on the vehicle.
1.12. 'Centre of reference`
means the intersection of the axis of reference with the light-emitting surface. This centre of reference is to be specified by the manufacturer of the lamp.
1.13. 'Angles of geometric visibility`
means the angles which determine the field of the minimum solid angle in which the apparent surface of the lamp must be visible. That field of the solid angle is determined by the segments of the sphere of which the centre coincides with the centre of reference of the lamp and the equator is parallel with the ground. These segments are determined in relation to the axis of reference. The horizontal angles â correspond to the longitude and the vertical angles á to the latitude.
There must be no obstacle on the inside of the angles of geometric visibility to the propagation of light from any part of the apparent surface of the lamp observed from infinity.
If measurements are taken closer to the lamp, there must be a parallel shift in the direction of observation to achieve the same accuracy.
N° account shall be taken of obstacles on the inside of the angles of geometric visibility, if they were already present when the lamp was type-approved.
If, when the lamp is installed, any part of the apparent surface of the lamp is hidden by any further parts of the vehicle, proof shall be furnished that the part of the lamp not hidden by obstacles still conforms to the photometric values prescribed for the approval of the device as an optical unit (see figure below).
1.14. 'Extreme outer edge`
on either side of the vehicle means the plane parallel to the median longitudinal plane of the vehicle and touching its lateral outer edge, disregarding the projection:
1.14.1. of tyres near their point of contact with the ground and connections for tyre pressure gauges;
1.14.2. of anti-skid devices which may be mounted on the wheels;
1.14.3. of rear-view mirrors;
1.14.4. of side direction indicator lamps, end-outline marker lamps, front and rear position lamps, parking lamps, retro reflectors and side-marker lamps;
1.14.5. of customs seals affixed to the vehicle and devices for securing and protecting such seals.
1.15. 'Overall width`
means the distance between the two vertical planes defined in item 1.14.
1.16. A 'single lamp`
means a device or part of a device, having one function and one illuminating surface and one or more light sources. For the purpose of installation on a vehicle, a 'single lamp` also means any assembly of two independent or grouped lamps, whether identical or not, having the same function, if they are installed such that the projections of the illuminating surfaces of the lamps on a given transverse plane occupy not less than 60 % of the smallest rectangle circumscribing the projections of the said illuminating surfaces.
In such a case, each of these lamps shall, where approval is required, be approved as a type 'D` lamp. This possible combination does not apply to main-beam headlamps, dipped-beam headlamps and front fog lamps.
1.17. 'Two lamps or an even number of lamps`
means a single light-emitting surface in the shape of a band if placed symmetrically in relation to the median longitudinal plane of the vehicle and extending on both sides to within not less than 400 mm of the extreme outer edge of the vehicle, and being not less than 800 mm long. The illumination of such a surface shall be provided by not less than two light sources placed as close as possible to its ends. The light-emitting surface may be constituted by a number of juxtaposed elements on condition that the projections of the several individual light-emitting surfaces on the same transverse plane occupy not less than 60 % of the area of the smallest rectangle circumscribing the projections of those individual light-emitting surfaces.
1.18. 'Distance between two lamps`
which face in the same direction means the shortest distance between the orthogonal projections in a plane perpendicular to the axes of reference of the outlines of the two illuminating surfaces as defined according to the case mentioned in item 1.9. The distance between two lamps may, however, be measured without determining the outlines of the illuminating surfaces exactly, where the distance is clearly in excess of the minimum requirements of the Directive.
1.19. 'Optional lamp`
means a lamp the presence of which is left to the discretion of the vehicle manufacturer.
1.20. 'Operational tell-tale`
means a light or auditory device showing whether a device that has been actuated is operating correctly or not.
1.21. 'Circuit-closed tell-tale`
means a light showing that a device has been switched on but not showing whether it is operating correctly or not.
1.22. 'Ground`
means the surface on which the vehicle stands, which should be substantially horizontal.
1.23. 'Movable components`of the vehicle means those body panels or other vehicle parts, the position of which can be changed by tilting, rotating or sliding without the use of tools. They do not include tiltable driver cabs.
1.24. 'Normal position of use of a movable component`
means the position(s) of a movable component specified by the vehicle manufacturer for the normal condition of use and the park condition of the vehicle.
1.25. 'Normal condition of use of a vehicle`
means:
1.25.1. for a motor vehicle, when the vehicle is ready to move with its propulsion engine running and its movable components in the normal position(s) as defined in item 1.24;
1.25.2. and for a trailer, when the trailer is connected to a drawing vehicle in the condition as described in item 1.25.1 and its movable components are in the normal position(s) as defined in item 1.24.
1.26. 'Park condition of a vehicle`
means:
1.26.1. for a motor vehicle, when the vehicle is at a standstill and its propulsion engine is not running and its movable components are in the normal position(s) as defined in item 1.24;
1.26.2. and for a trailer, when the trailer is connected to a drawing vehicle in the condition as described in item 1.26.1 and its movable components are in the normal position(s) as defined in item 1.24.
APPLICATION FOR EC TYPE-APPROVAL
2.1. The application for EC approval of a vehicle type with regard to the installation of its lighting and light-signalling devices shall be submitted by the vehicle manufacturer or his representative.
2.2. It shall be accompanied by the following documents in triplicate, and by the following particulars:
2.2.1. a description of the vehicle type in accordance with the points listed in 1.1, together with the restrictions on loading, particularly the maximum permissible load in the boot;
2.2.2. a list of devices prescribed by the manufacturer for the lighting and light-signalling assembly. The list may include several types of device for each operation. Each type must be duly identified (component type-approval mark, name of manufacturer, etc.);
2.2.3. layout drawing of the lighting and light-signalling equipment as a whole, showing the position of the various lamps on the vehicle;
2.2.4. if necessary, in order to verify conformity to the requirements of the present Directive, layout drawing(s) for each individual lamp showing the illuminating surface as defined in items 1.9.1, 1.9.2 and 1.9.3, the light-emitting surface as defined in item 1.8, the axis of reference as defined in item 1.11 and the centre of reference as defined in item 1.12. This information is not necessary in the case of the rear registration plate lamp (item 1.7.15).
2.3. An unladen vehicle fitted with lighting and light-signalling equipment as described in item 2.2.2 and representative of the vehicle type to be approved, must be submitted to the technical authority conducting approval tests.
2.4. The document provided for in Annex II shall be attached to the type-approval document.
GENERAL SPECIFICATIONS
3.1. Without prejudice to the provisions of this Annex, solely the installation of the lighting and light-signalling devices defined in items 1.7.8 to 1.7.22 shall be permitted. The installation of any other lighting or light-signalling device is consequently prohibited.
3.2. The lighting and light-signalling devices must be so fitted that under normal conditions of use as defined in items 1.25, 1.25.1 and 1.25.2, and notwithstanding any vibration to which they may be subjected, they retain the characteristics laid down in this Annex and enable the vehicle to comply with the requirements of this Annex. In particular, it shall not be possible for the adjustment of the lamps to be inadvertently disturbed.
3.3. The illuminating lamps described in items 1.7.8, 1.7.9 and 1.7.10 must be so fitted that a correct setting of their alignment can easily be performed.
3.4. For all light-signalling devices, including those mounted on the side panels, the reference axis of the lamp when fitted to the vehicle must be parallel to the bearing plane of the vehicle on the road; in addition it must be perpendicular to the median longitudinal plane of the vehicle in the case of side retro reflectors and of side-marker lamps and parallel to that plane in the case of all other signalling devices. In each direction a tolerance of p 3o shall be allowed. In addition, any specific instructions as regards fitting laid down by the manufacturer must be complied with.
3.5. In the absence of specific requirements, the height and alignment of the lamps shall be checked with the unladen vehicle placed on a flat, horizontal surface under the conditions defined in items 1.25, 1.25.1 and 1.25.2.
3.6. In the absence of specific requirements, lamps constituting a pair shall:
3.6.1. be fitted to the vehicle symmetrically in relation to the median longitudinal plane (this estimate to be based on the exterior geometrical form of the lamp and not on the edge of its illuminating surface referred to in items 1.9.1, 1.9.2 and 1.9.3);
3.6.2. be symmetrical to one another in relation to the median longitudinal plane; this requirement is not valid with regard to the interior structure of the lamp;
3.6.3. satisfy the same colorimetric characteristics;
3.6.4. have substantially identical photometric characteristics.
3.7. On vehicles whose external shape is asymmetrical, the above requirements shall be satisfied as far as possible.
3.8. Lamps having different functions may be independent or be grouped, combined or reciprocally incorporated in one device, provided that each such lamp complies with the requirements applicable to it.
3.9. The maximum height above ground shall be measured from the highest point and the minimum height from the lowest point of the illuminating surface.
In the case of dipped headlamps, the minimum height in relation to the ground is measured from the lowest edge of the reflector.
3.9.1. The position, as regards width, shall be determined from the edge of the illuminating surface which is the furthest from the median longitudinal plane of the vehicle when referred to the overall width, and from the inner edges of the illuminating surfaces when referred to the distance between the lamps.
3.10. In the absence of specific requirements no lamps other than direction indicator lamps and the hazard warning signal may emit a flashing light.
3.11. N° red light which could give rise to confusion shall be emitted from a lamp as defined in item 1.7 in a forward direction and no white light which could give rise to confusion, other than from the reversing lamp, shall be emitted from a lamp as defined in item 1.7 in a rearward direction. N° account shall be taken of lighting devices fitted in the interior of the vehicle. In case of doubt, this requirement shall be verified as follows:
3.11.1. for the visibility of red light towards the front: there must be no direct visibility of the light-emitting surface of a red lamp if viewed by an observer moving within Zone 1 in a transverse plane situated 25 m in front of the vehicle (see Appendix 3, Figure 1);
3.11.2. for the visibility of white light towards the rear: there must be no direct visibility of the light-emitting surface of a white lamp if viewed by an observer moving within Zone 2 in a transverse plane situated 25 m behind the vehicle (see Appendix 3, Figure 2).
3.11.3. Zones 1 and 2, as seen by the observer, are limited in their respective planes as follows:
3.11.3.1.
as regards height, by two horizontal planes which are 1 and 2.2 m respectively above the ground;
3.11.3.2.
as regards width, by two vertical planes which make an angle of 15o towards the front and rear respectively, and outside the vehicle by reference to the median plane of the vehicle, passing through the point (or points) of contacts of vertical planes which are parallel to the median longitudinal plane of the vehicle, and limiting the overall width of the vehicle.
If there are several points of contact, the one which is furthest forward shall correspond to the front plane and the one furthest rearward shall correspond to the rear plane.
3.12. The electrical connections must be such that the front and rear position lamps, the end-outline marker lamps, where fitted, the side-marker lamps, where fitted, and the rear registration plate lamp can only be switched on and off simultaneously.
This requirement shall not apply when using front and rear position lamps, as well as side-marker lamps combined or reciprocally incorporated with said lamps, as parking lamps.