This Annex applies to the type-approval, as separate technical units within the meaning of Article 2 of Directive 70/156/EEC, of exhaust systems or components thereof to be fitted to one or more given types of motor vehicle in categories M1 and N1 as replacement parts.
1.1.
Replacement exhaust system or component thereof means any part of the exhaust system defined in section 1.2.1 of Annex I intended to replace on a vehicle a part of the type granted EEC type-approval with the vehicle in accordance with Annex I.
2.1.
The application of EC type-approval pursuant to Article 3 (4) of Directive 70/156/EEC in respect of a replacement exhaust system or component thereof as a separate technical unit shall be submitted by the vehicle manufacturer or the manufacturer of the separate technical unit in question.
2.2.
A model for the information document is given in Appendix 1.
2.2.1.
a description of the type(s) of vehicle to which the system or components thereof are to be fitted with reference to the characteristics mentioned in item 1.1 of Annex I. The numbers and/or symbols designating the engine and vehicle type must be indicated,
2.2.2.
a description of the replacement exhaust system indicating the relative position of each system component, together with mounting instructions,
2.2.3.
detailed drawings of each component, so that they can be easily located and identified, and reference to the materials used.
These drawings must indicate the place provided for the compulsory affixing of the EEC type-approval.
2.3.
At the request of the technical service concerned, the applicant must submit:
2.3.1. — two examples of the system in respect of which application for EEC type-approval has been made,
2.3.2. — an exhaust system of the type originally fitted to the vehicle when EEC type-approval was granted,
2.3.3. — a vehicle representative of the type to which the system is to be fitted, which meets the requirements of item 4.1 of Annex III, part I,
2.3.4. — a separate engine corresponding to the type of vehicle described above.
2.4.
Before granting type approval the competent authority must verify the existence of satisfactory arrangements for ensuring effective control of the conformity of production.
2.4.1.
The replacement exhaust system or its components, excluding fixing hardware and pipes must bear:
2.4.1.1. — the trademark or trade name of the manufacturer of the replacement system and its components,
2.4.1.2. — the manufacturer's trade description,
3.1.3. — the EEC type-approval number.
2.4.1.2.
These marks must be clearly legible and indelible, even when the system is fitted to the vehicle.
3.1. If the relevant requirements are satisfied, EC type-approval pursuant to Article 4 (3) and, if applicable, Article 4 (4) of Directive 70/156/EEC shall be granted.
3.2. A model for the EC type-approval certificate is given in Appendix 2.
3.3. A type-approval number in accordance with Annex VII to Directive 70/156/EEC shall be assigned to each type of replacement exhaust system or component thereof approved as a separate technical unit; section 3 of the type-approval number shall indicate the number of the amending Directive which was applicable at the time of the vehicle type-approval. The same Member State shall not assign the same number to another type of replacement exhaust system or component thereof.
4.1. Every replacement exhaust system or component thereof, excluding fixing hardware and pipes, conforming to a type approved under this Directive shall bear an EC type-approval mark.
4.2. The EC type-approval mark shall consist of a rectangle surrounding the lower case letter ‘e’ followed by the distinguishing letter(s) or number of the Member State which has granted the approval:
‘1’ for Germany
‘2’ for France
‘3’ for Italy
‘4’ for the Netherlands
‘5’ for Sweden
‘6’ for Belgium
‘7’ for Hungary
‘8’ for the Czech Republic
‘9’ for Spain
‘11’ for the United Kingdom
‘12’ for Austria
‘13’ for Luxembourg
‘17’ for Finland
‘18’ for Denmark
‘19’ for Romania
‘20’ for Poland
‘21’ for Portugal
‘23’ for Greece
‘26’ for Slovenia
‘27’ for Slovakia
‘29’ for Estonia
‘32’ for Latvia
‘34’ for Bulgaria
‘36’ for Lithuania
‘CY’ for Cyprus
‘IRL’ for Ireland
‘MT’ for Malta
It must also include in the vicinity of the rectangle the ‘base approval number’ contained in section 4 of the type-approval number referred to in Annex VII to Directive 70/156/EEC, preceded by the two figures indicating the sequence number assigned to the most recent major technical amendment to Council Directive 70/157/EEC which was applicable at the time of the vehicle type-approval. For Directive 70/157/EEC, the sequence number is 00; for Directive 77/212/EEC the sequence number is 01; for Directive 84/424/EEC the sequence number is 02; for Directive 92/97/EEC the sequence number is 03.
4.3. The mark must be clearly legible and indelible even when the replacement exhaust system or component thereof is fitted to the vehicle.
4.4. An example of the EC type-approval mark is shown in Appendix 3.
5.1.1.
The replacement exhaust systems or component thereof must be designed, constructed and capable of being mounted so as to ensure that the vehicle complies with the provisions of this Directive under normal conditions of use, notwithstanding any vibrations to which it may be subject.
5.1.2.
The exhaust system or components thereof must be designed, constructed and capable of being mounted so that reasonable resistance to the corrosion phenomena to which it/they is/are exposed is obtained having regard to the conditions of use of the vehicle.
5.1.3.
Exhaust systems shall be carefully installed on the vehicle. In particular, it shall be checked that the complete exhaust system will not noticeably leak after installation.
5.2.1.
The acoustic efficiency of the replacement exhaust system or component thereof must be checked using the methods described in sections 5.2.2.4 and 5.2.3.4 of Annex I [As prescribed in the version of this Directive which was applicable to the type-approval of the vehicle.].
When the replacement exhaust system or component thereof is mounted on the vehicle referred to in section 2.3.3 of this Annex, the sound levels obtained using the two methods (stationary and moving vehicle) must satisfy one of the following conditions:
5.2.1.1. they must not exceed the values obtained when this type of vehicle was granted EEC type-approval;
5.2.1.2. they must not exceed the sound level values measured on the vehicle, referred to in 2.3.3, when this is fitted with an exhaust system of the same type as that fitted to the vehicle when EEC type-approval was granted.
5.3.1.
The replacement exhaust system or components thereof must be such as to ensure that vehicle performance is comparable with that achieved with the original equipment exhaust system or component thereof.
5.3.2.
The replacement exhaust system or, depending on the manufacturer's choice, the components of this system, must be compared with the original equipment exhaust system or components thereof, which are also in new condition, fitted in turn to the vehicle referred to in 2.3.3.
5.3.3.
The check must take the form of a measurement of pressure loss under the conditions specified in 5.3.4.1 or 5.3.4.2. The value measured with the replacement exhaust system must not exceed the value measured with the original equipment system by more than 25 % under the conditions mentioned below.
The measurement must be conducted on the engine referred to in 2.3.4 coupled to a dynamometer.
With the throttle completely open, the bench must be so adjusted as to obtain the engine speed (S) corresponding to the rated maximum power of the engine.
For the measurement of back pressure, the pressure tap must be placed at the distance from the exhaust manifold specified in Figures 1, 2 and 3.
The measurements must be carried out on the vehicle referred to in item 2.3.3.
The test must be conducted:
either on road,
or
on a roller dynamometer.
With the throttle completely open, the engine must be loaded so as to obtain the engine speed (S) corresponding to the rated maximum power.
For the measurement of back pressure, the pressure tap must be placed at the distance from the exhaust manifold specified in Figures 1, 2 and 3.
Fibrous materials must not be used in the manufacture of replacement exhaust systems or components thereof unless appropriate measures are taken during the design and production stages to ensure that a level of efficiency is attained corresponding to the limits set out in section 5.2.2.1 of Annex I.
Such a silencing system is deemed to be effective in traffic if the exhaust gases are not in contact with the fibrous materials or if, after the removal of the fibrous materials, the sound levels comply with the requirements set out in 5.2.1, when the exhaust system is tested on a vehicle in accordance with the methods described in sections 5.2.2 and 5.2.3 of Annex I.
If this condition is not observed, the entire exhaust system must be subjected to conditioning. This must be done using one of the three methods described in sections 5.3.1.1, 5.3.1.2 and 5.3.1.3 of Annex I.
After conditioning, the sound level must be checked as specified in 5.2.1 above.
When the procedure described in item 5.2.1.2 is employed, the applicant for EEC type-approval may ask for the conditioning of the original equipment exhaust system or submit one which has been emptied.
6.1. In the case of modifications of the type approved pursuant to this Directive, the provisions of Article 5 of Directive 70/156/EEC shall apply.
7.1. Measures to ensure the conformity of production shall be taken in accordance with the requirements laid down in Article 10 to Directive 70/156/EEC.
7.2. Special provisions:
7.2.1. The tests referred to item 2.3.5. of Annex X to Directive 70/156/EEC are those prescribed in Annex III (II) to this Directive.
7.2.2. The frequency of inspections referred to in item 2.4. of Annex X to Directive 70/156/EEC is normally one every two years.
The exhaust system or component thereof bearing the above EC type-approval mark is a device which has been approved in Spain (e 9) pursuant to Directive 92/97/EEC (03) under the base approval number 0148.
The figures used are only indicative.