Pursuant to point (h) of Article 2(2) of Section 4 of Part B of Annex 31 to the Trade and Cooperation Agreement, fourth indent, Annex I C to Implementing Regulation (EU) 2016/799 is adapted as follows.
The following adaptations apply throughout Annex I C, including its Appendices 1 to 17:
in the case of the United Kingdom, the references to ‘Member State’ or ‘Member States’, wherever they occur, are replaced by ‘Party’, except for the references in point (229) of subsection 4.1 and in point (424) of Section 7;
for ‘Regulation (EEC) No 3820/85’ and ‘Regulation (EC) No 561/2006’ substitute ‘Section 2 of Part B of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
for ‘Regulation (EU) No 165/2014’ substitute ‘Section 4 of Part B and Section 2 of Part C of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’, except for the references in points (226d), (237), (402), (424), ITS_01 and MIG_025;
for ‘Directive (EU) 2015/719’ and for ‘Council Directive 96/53/EC’ substitute ‘Section 1 of Part C of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
for ‘Annex I B to Regulation (EEC) No 3821/85’ substitute ‘Annex I B to Regulation (EEC) No 3821/85 as adapted by Appendix 31-B-4-2 of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
Section 1 (Definitions) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
point (u) is replaced by the following:
‘(u) ‘effective circumference of the wheels’ means: the average of the distances travelled by each of the wheels moving the vehicle (driving wheels) in the course of one complete rotation. The measurement of those distances shall be made under standard test conditions as defined under requirement 414 and is expressed in the form ‘l = … mm’. Vehicle manufacturers may replace the measurement of those distances by a theoretical calculation which takes into account the distribution of the weight on the axles, vehicle unladen in normal running order, namely with coolant fluid, lubricants, fuel, tools, spare-wheel and driver. The methods for such theoretical calculation are subject to approval by the competent authority in a Party and can take place only before tachograph activation;’;
in point (hh), the reference to ‘Council Directive 92/6/EEC’ is replaced by ‘the applicable law of each Party’;
in point (uu), the reference to ‘Directive 92/23/EEC’ is replaced by ‘UNECE Regulation No 54’;
the footnote in point (vv) is replaced by the following:
‘“Vehicle Identification Number” means a fixed combination of characters assigned to each vehicle by the manufacturer, which consists of two sections: the first, composed of not more than six characters (letters or figures), identifying the general characteristics of the vehicle, in particular the type and model; the second, composed of eight characters of which the first four may be letters or figures and the other four figures only, providing, in conjunction with the first section, clear identification of a particular vehicle.’;
in point (yy), the first indent is replaced by the following:
‘— installed and used only in M1 and N1 type vehicles as defined in the Consolidated Resolution on the Construction of Vehicles (R.E.3);’;
point (aaa) is deleted;
in point (ccc), the definition of ‘introduction date’ is replaced by ‘the date of application of Decision No 1/2023 of the Specialised Committee on Road Transport established by the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
Section 2 (General characteristics and functions of the recording equipment) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
the last subparagraph of paragraph (7) of subsection 2.1 is replaced by the following:
‘This is done in accordance with Article 4 of Section 2 of Part C of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part.’;
Section 3 (Construction and functional requirements for recording equipment) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
point (201) of subsection 3.20 is replaced by the following:
‘The vehicle unit may also be able to output the following data using an appropriate dedicated serial link independent from an optional CAN bus connection (ISO 11898 Road vehicles – Interchange of digital information – Controller Area Network (CAN) for high speed communication), to allow their processing by other electronic units installed in the vehicle:
current UTC date and time,
speed of the vehicle,
total distance travelled by the vehicle (odometer),
currently selected driver and co-driver activity,
information if any tachograph card is currently inserted in the driver slot and in the co-driver slot and (if applicable) information about the corresponding cards identification (card number and issuing country).
Other data may also be output in addition to that minimum list.
When the ignition of the vehicle is ON, those data shall be permanently broadcast. When the ignition of the vehicle is OFF, at least any change of driver or co-driver activity and/or any insertion or withdrawal of a tachograph card shall generate a corresponding data output. In the event that data output has been withheld whilst the ignition of the vehicle is OFF, that data shall be made available once the ignition of the vehicle is ON again.
The driver consent shall be required in case personal data are transmitted.’;
in point (226d) of section 3.28,‘, in accordance with Article 12(5) of Regulation (EU) No 165/2014’ is deleted;
Section 4 (Construction and functional requirements for tachograph cards) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in point (229) of subsection 4.1, the following subparagraph is added:
‘For the United Kingdom, the distinguishing sign shall be: UK’;
in point (237), for ‘Article 26.4 of Regulation (EU) No 165/2014’ substitute ‘Article 9(2) of Section 2 of Part C of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
in point (241) of subsection 4.4, the word ‘Community territory’ is replaced by ‘the territory of the Union and of the United Kingdom’;
Section 5 (Installation of recording equipment) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
The first paragraph of point (397) in subsection 5.2 is replaced by the following:
‘(397) For M1 and N1 vehicles only, and which are fitted with an adaptor in conformity with Appendix 16 of this Annex and where it is not possible to include all the information necessary, as described in Requirement 396, a second, additional, plaque may be used. In such cases, this additional plaque shall contain at least the last four indents described in Requirement 396.’;
In point (402) of subsection 5.3, for ‘Article 22(3) of Regulation (EU) No 165/2014’ substitute ‘Article 5(3) of Section 2 of Part C of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part.’;
Section 6 (Checks, inspections and repairs) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
the introductory sentence is replaced by the following: ‘Requirements on the circumstances in which seals may be removed are defined in Chapter 5.3 of this Annex.’;
Section 7 (Card issuing) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in point (424), after the reference to ‘Member States‘ insert ‘and the United Kingdom’, and for the reference to ‘Article 31 of Regulation (EU) No 165/2014’ substitute ‘Article 13 of Section 2 of Part C of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
Appendix 1 (Data dictionary) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in point 2.163, for ‘Directive 92/23/EEC’ substitute ‘UNECE Regulation No 54’;
Appendix 11 (Common security mechanisms) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in point 9.1.4 (Equipment Level: Vehicle Units), in the first note below CSM_78, for ‘Regulation (EU) No 581/2010’ substitute ‘Article 7(5) of Section 2 of Part B Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
in point 9.1.5 (Equipment level: Tachograph Cards), in the note below CSM_89, for ‘Regulation (EU) No 581/2010’ substitute ‘Article 7(5) of Section 2 of Part B Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
Appendix 12 (Positioning based on Global Navigation Satellite System (GNSS)) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in Section 2 (Basic Characteristics of the GNSS Receiver), the reference to ‘compatibility with the services provided by the Galileo and European Geostationary Navigation Overlay Service (EGNOS) programmes as set out in Regulation (EU) No 1285/2013 of the European Parliament and of the Council’, is replaced by ‘compatibility with Satellite Based Augmentation Systems (SBAS)’;
Appendix 13 (ITS Interface) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in requirement ITS_01, the terms ‘, requested in Articles 10 and 11 of Regulation (EU) No 165/2014’ are deleted;
Appendix 15 (Migration: Managing the co-existence of equipment generations and versions) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in subsection 2.2, ‘Annex I C of this Regulation’ is replaced by ‘Annex I C of this Regulation as adapted by Decision No 1/2023 of the Specialised Committee on Road Transport established by the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of the one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
in requirement MIG_025 in subsection 5, ‘Article 34(7) of Regulation (EU) No 165/2014’ is replaced by ‘Article 6(7) of Section 4 of Part B of Annex 31 to the Trade and Cooperation Agreement between the European Union and the European Atomic Energy Community, of one part, and the United Kingdom of Great Britain and Northern Ireland, of the other part’;
Appendix 16 (Adaptor for M1 and N1 category vehicles) of Annex I C to Implementing Regulation (EU) 2016/799 is further adapted as follows:
in point 5.1 in the table under Section (7) (Type approval of recording equipment when an adaptor is used), the reference to ‘Directive 2006/28/EC’ is replaced by ‘UNECE Regulation No 10’.