1 ATTACHMENT A, 2011/115/EU: Decision No 1/2010 of the Committee established under the Agreement between…

In forcesince 18 Oct 2010

In Annex 1, Product Sectors, Chapter 12, Motor vehicles, the text should be deleted and replaced by the following one:

European Union |

1.

Directive 2007/46/EC of the European Parliament and of the Council of 5 September 2007 establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles (Framework Directive) (OJ L 263, 9.10.2007, p. 1), as last amended by Regulation (EC) No 661/2009 of the European Parliament and of the Council of 13 July 2009 (OJ L 200, 31.7.2009, p. 1), and taking into account the acts listed in Annex IV to Directive 2007/46/EC, as amended until 14 October 2009 and amendments to the aforementioned Annex respectively to acts listed therein, accepted according to the procedure described in Section V, paragraph 1 (hereinafter together referred to as “Framework Directive 2007/46/EC”)

Switzerland |

100.

Ordinance of 19 June 1995 relating to the technical requirements for power-driven transportation vehicles and their trailers (RO 1995 4145), as amended until 14 October 2009 (RO 2009 5705) and taking into account amendments accepted according to the procedure described in Section V, paragraph 1

101.

Ordinance of 19 June 1995 relating to the type approval of road vehicles (RO 1995 3997), as amended until 14 October 2009 (RO 2009 5805) and taking into account amendments accepted according to the procedure described in Section V, paragraph 1

The Committee established pursuant to Article 10 of this Agreement shall draw up and keep up-to-date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established pursuant to Article 10 of this Agreement shall draw up and keep up-to-date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, the designating authorities shall refer to their respective legislative, regulatory and administrative provisions as listed in Section I.

The provisions of this Section shall apply exclusively to relations between Switzerland and the European Union.

The legislation adopted in the European Union and listed in Annex IV to Directive 2007/46/EC after 14 October 2009 shall be considered to be part of the provisions covered by Article 1(2) of this Agreement after the accomplishment of the following procedure:

(a)

without prejudice to Article 12(2) of this Agreement, the European Union shall notify Switzerland of the changes to Annex IV to Directive 2007/46/EC respectively to acts listed therein without delay after their publication in the Official Journal of the European Union;

(b)

Switzerland shall notify the European Union of the acceptance of the new provisions and of the adoption of the corresponding Swiss legislation before those changes apply in the European Union;

(c)

the changes in the legislative provisions shall be deemed to be included in Section I on the date of the notification by Switzerland.

The Joint Committee will take regular note of the abovementioned changes. The introduction of these changes will be made publicly available.

The competent type-approval authorities in Switzerland and the Member States shall in particular exchange the information referred to in Article 8(5) to (8) of the Framework Directive 2007/46/EC.

In the event of refusal by Switzerland or a Member State to grant type-approval in accordance with Article 8(3) of the Framework Directive 2007/46/EC, it shall immediately send the other Member States, Switzerland and the Commission a detailed file explaining the reasons for its decision and setting out the evidence for its findings.

Switzerland shall also recognise vehicle type-approval granted before the entry into force of this Agreement in accordance with Council Directive 70/156/EEC of 6 February 1970 (OJ L 42, 23.2.1970, p. 1), as last amended by Commission Directive 2007/37/EC of 21 June 2007 (OJ L 161, 22.6.2007, p. 60), by the authorities responsible for type-approval where that approval is still valid in the European Union.

The European Union shall recognise Swiss type-approval where Switzerland’s requirements are deemed to be equivalent to those of the Framework Directive 2007/46/EC.

Recognition of Swiss-issued type-approval shall be suspended should Switzerland fail to adapt its legislation to all the European Union type-approval legislation in force.

1.

If a Member State or Switzerland finds that new vehicles, systems, components or separate technical units, albeit in compliance with the applicable requirements or properly marked, present a serious risk to road safety, or seriously harm the environment or public health, that State may, for a maximum period of 6 months, refuse to register such vehicles or to permit the sale or entry into service in its territory of such vehicles, components or separate technical units.

In such cases, the Member State concerned or Switzerland shall immediately notify the manufacturer, the other Member States, Switzerland and the Commission accordingly, stating the reasons on which its decision is based.

2.

The Commission and Switzerland shall consult the Parties concerned as soon as possible and, in particular, their respective approval authorities that granted the type-approval. The Committee shall be kept informed and, where necessary, shall hold appropriate consultations with the view to reaching a settlement.

1.

If a Member State or Switzerland which has granted a type-approval finds that new vehicles, systems, components or separate technical units accompanied by a certificate of conformity or bearing an approval mark do not conform to the type it has approved, it shall take the necessary measures, including, where necessary, the withdrawal of type-approval, to ensure that production vehicles, systems, components or separate technical units, as the case may be, are brought into conformity with the approved type. The approval authority of that Member State or Switzerland shall advise the approval authorities of the other Member States and/or Switzerland of the measures taken.

2.

For the purposes of paragraph 1, deviations from the particulars in the type-approval certificate or the information package shall be deemed to constitute failure to conform to the approved type.

A vehicle shall not be deemed to deviate from the approved type where tolerances are permitted by the relevant regulatory acts and those tolerances are respected.

3.

If a Member State or Switzerland demonstrates that new vehicles, components or separate technical units accompanied by a certificate of conformity or bearing an approval mark do not conform to the approved type, it may ask the Member State or Switzerland which granted the type-approval to verify that vehicles, systems, components or separate technical units in production continue to conform to the approved type. On receipt of such a request, the Member State concerned or Switzerland shall take the requisite action as soon as possible and in any case within 6 months of the date of the request.

4.

The approval authority shall request the Member State or Switzerland which granted the system, component, separate technical unit or incomplete vehicle type-approval to take the necessary action to ensure that vehicles in production are brought back into conformity with the approved type in the following cases:

(a)

in relation to a vehicle type-approval, where the non-conformity of a vehicle is attributable exclusively to the non-conformity of a system, component or separate technical unit;

(b)

in relation to a multi-stage type-approval, where the non-conformity of a completed vehicle is attributable exclusively to the non-conformity of a system, component or separate technical unit being part of the incomplete vehicle, or of the incomplete vehicle itself.

On receipt of such a request, the Member State concerned or Switzerland shall take the requisite action, if necessary in conjunction with the Member State making the request or Switzerland, as soon as possible and in any case within 6 months of the date of the request. Where a failure to conform is established, the approval authority of the Member State or Switzerland which granted the system, component or separate technical unit type-approval or the approval of the incomplete vehicle shall take the measures set out in paragraph 1.

5.

The approval authorities shall inform each other within 20 working days of any withdrawal of type-approval and of the reasons therefor.

6.

If the Member State or Switzerland that granted type-approval disputes the failure to conform notified to it, the Member States concerned and Switzerland shall endeavour to settle the dispute. The Committee shall be kept informed and, where necessary, shall hold appropriate consultations with a view to reaching a settlement.’

  • Decision_act (EU) 2007/37Law

  • celex=32007L0046
  • celex=31970L0156
  • celex=32007L0037
  • celex=32007L0047
  • celex=32009R0661
  • num:eu=1970/156
  • num:eu=2007/46