2 ‘ANNEX 1, 2009/455/EC: Decision No 2/2008 of 16 May 2008 of the Committee updating the legal refer…

In forcesince 16 May 2008

This Annex is divided up into the following chapters by sector:

European Community | 1. | Directive 98/37/EC of the European Parliament and of the Council of 22 June 1998 on the approximation of the laws of the Member States relating to machinery (OJ L 207, 23.7.1998, p. 1), as last amended by Directive 98/79/EC of the European Parliament and of the Council of 27 October 1998 (OJ L 331, 7.12.1998, p. 1).

Switzerland | 100. | Federal Law of 19 March 1976 on the safety of technical installations and equipment (RO 1977 2370), as last amended on 18 June 1993 (RO 1995 2766).

101.

| Ordinance of 12 June 1995 on the safety of technical installations and equipment (RO 1995 2770), as last amended on 27 March 2002 (RO 2002 853).

102.

| Ordinance of 12 June 1995 on the procedures of conformity assessment of technical installations and equipment (RO 1995 2783).

The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established under Article 10 of this Agreement shall draw up and keep up to date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and the assessment criteria set out in Annex VII to Directive 98/37/EC.

The legislative, regulatory and administrative provisions listed in section I shall not apply to second-hand machinery.

The principle contained in Article 1 paragraph 2 of this Agreement shall apply, however, to machinery legally placed on the market and/or put into service in one of the Parties and exported as second-hand machinery to the market of the other Party.

The other provisions relating to second-hand machinery, e.g. those relating to safety in the place of work in force in the importing state, shall remain applicable.

European Community | 1. | Council Directive 89/686/EEC of 21 December 1989 on the approximation of the laws of the Member States relating to personal protective equipment, as last amended by Regulation (EC) No 1882/2003 of the European Parliament and of the Council of 29 September 2003 (OJ L 284, 31.10.2003, p. 1).

Switzerland | 100. | Federal Law of 19 March 1976 on the safety of technical installations and equipment (RO 1977 2370), as last amended on 18 June 1993 (RO 1995 2766).

101.

| Ordinance of 12 June 1995 on the safety of technical installations and equipment (RO 1995 2770), as last amended on 27 March 2002 (RO 2002 853).

102.

| Ordinance of 12 June 1995 on the procedures of conformity assessment of technical installations and equipment (RO 1995 2783).

The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established under Article 10 of this Agreement shall draw up and keep up to date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and the assessment criteria set out in Annex V to Directive 89/686/EEC.

European Community | 1. | Council Directive 88/378/EEC of 3 May 1988 on the approximation of the laws of the Member States concerning the safety of toys (OJ L 187, 16.7.1988, p. 1) and corrected by corrigenda (OJ L 281, 14.10.1988, p. 55 and OJ L 37, 9.2.1991, p. 42), as last amended by Council Directive 93/68/EEC of 22 July 1993 (OJ L 220, 30.8.1993, p. 1).

Switzerland | 100. | Federal Law of 9 October 1992 on foodstuffs and commodities (RO 1995 1469) as last amended on 21 March 2003 (RO 2003 4803).

101.

| Ordinance of 23 November 2005 on foodstuffs and commodities (RO 2005 5451) as last amended on 15 November 2006 (RO 2006 4909).

102.

| Ordinance of EDI of 27 March 2002 on the safety of toys (RO 2002 1082) as last amended on 15 November 2006 (RO 2006 5157).

The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established under Article 10 of this Agreement shall draw up and keep up to date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and the assessment criteria set out in Annex III to Directive 88/378/EEC.

In accordance with Article 10(4) of Directive 88/378/EEC, the designating authorities may obtain on request a copy of the certificate and, on reasoned request, a copy of the technical file and the reports on the examinations and tests carried out.

In accordance with Article 10(5) of Directive 88/378/EEC, the Swiss bodies shall inform the Swiss Federal Office of Public Health when refusing to issue an EC type-examination certificate. The Federal Office shall likewise notify the Commission of the European Communities thereof.

European Community | 1. | Council Directive 90/385/EEC of 20 June 1990 on the approximation of the laws of the Member States relating to active implantable medical devices, as last amended by Regulation (EC) No 1882/2003 of the European Parliament and of the Council of 29 September 2003 (OJ L 284, 31.10.2003, p. 1).

2.

| Council Directive 93/42/EEC of 14 June 1993 concerning medical devices, as last amended by Regulation (EC) No 1882/2003 of the European Parliament and of the Council of 29 September 2003 (OJ L 284, 31.10.2003, p. 1).

3.

| Directive 98/79/EC of the European Parliament and of the Council of 27 October 1998 on in vitro diagnostic medical devices (OJ L 331, 7.12.1998, p. 1), as last amended by Regulation (EC) No 1882/2003 of the European Parliament and of the Council of 29 September 2003 (OJ L 284, 31.10.2003, p. 1) and corrected by corrigenda (OJ L 22, 29.1.1999, p. 75 and OJ L 6, 10.1.2002, p. 70).

4.

| Commission Decision 2002/364/EC of 7 May 2002 on common technical specifications for in vitro diagnostic medical devices (OJ L 131, 16.5.2002, p. 17).

5.

| Commission Directive 2003/12/EC of 3 February 2003 on the reclassification of breast implants in the framework of Directive 93/42/EEC concerning medical devices (OJ L 28, 4.2.2003, p. 43).

6.

| Commission Directive 2003/32/EC of 23 April 2003 introducing detailed specifications as regards the requirements laid down in Council Directive 93/42/EEC with respect to medical devices manufactured utilising tissues of animal origin (OJ L 105, 26.4.2003, p. 18) and corrected by corrigendum (OJ L 6, 8.1.2005, p. 10).

7.

| Commission Directive 2005/50/EC of 11 August 2005 on the reclassification of hip, knee and shoulder joint replacements in the framework of Council Directive 93/42/EEC concerning medical devices (OJ L 210, 12.8.2005, p. 41).

8.

| Commission Regulation (EC) No 2007/2006 of 22 December 2006 implementing Regulation (EC) No 1774/2002 of the European Parliament and of the Council as regards the importation and transit of certain intermediate products derived from Category 3 material intended for technical uses in medical devices, in vitro diagnostics and laboratory reagents and amending that Regulation (OJ L 379, 28.12.2006, p. 98).

9.

| Directive 2007/47/EC of the European Parliament and of the Council of 5 September 2007 amending Council Directive 90/385/EEC on the approximation of the laws of the Member States relating to active implantable medical devices, Council Directive 93/42/EEC concerning medical devices and Directive 98/8/EC concerning the placing of biocidal products on the market (OJ L 247, 21.9.2007, p. 21).

Switzerland | 100. | Federal Law of 15 December 2000 on medicinal products and medical devices (RO 2001 2790), as last amended on 20 December 2006 (RO 2006 5599).

101.

| Federal Law of 24 June 1902 concerning the electrical weak and heavy current installations (RO 19 252 et RS 4 798), as last amended on 17 June 2005 (RO 2006 2197).

102.

| Federal Law of 9 June 1977 on metrology (RO 1977 2394), as last amended on 17 June 2005 (RO 2006 2197).

103.

| Federal law of 22 March 1991 on radiation protection (RO 1994 1933), as last amended on 21 March 2003 (RO 2004 4719).

104.

| Ordinance of 17 October 2001 on medical devices (RO 2001 3487), as last amended on 18 May 2005 (RO 2005 2695).

105.

| Ordinance of 18 April 2007 on import, transit and export of animals and animal products (RO 2007 1847).

The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established under Article 10 of this Agreement shall draw up and keep up to date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and the assessment criteria set out in Annex XI to Directive 93/42/EEC, in Annex 8 to Directive 90/385/EEC and in Annex IX to Directive 98/79/EC, in respect of the bodies designated under those Directives.

Any manufacturer or his authorised representative who places on the market of one of the Parties the medical devices referred to in Article 14 of Directive 93/42/EEC or Article 10 of Directive 98/79/EC shall inform the competent authorities of the Party in which he has his registered place of business of the particulars referred to in those Articles. The Parties shall reciprocally recognise that registration. The manufacturer shall not be obliged to designate a person responsible for placing devices on the market established in the territory of the other Party.

Manufacturers of both Parties shall indicate their name or trade name and address on the label of medical devices specified in Annex 1, point 13.3(a) to Directive 93/42/EEC and in vitro diagnostic medical devices specified in Annex 1, point 8.4(a), to Directive 98/79/EC. They shall not be obliged to indicate the name and address of the person responsible for placing the device on the market, of the representative or of the importer established within the territory of the other Party on the label, outer packaging or instructions for use.

For devices imported from third countries, in view of their distribution in the Community and Switzerland, the label, or the outer packaging, or instructions for use, shall contain the name and address of the single authorised representative of the manufacturer established within the Community or Switzerland, as appropriate.

In accordance with Article 9 of the Agreement, the Parties shall in particular exchange the information referred to in Article 8 of Directive 90/385/EEC, Article 10 of Directive 93/42/EEC and Article 11 of Directive 98/79/EC.

The competent Swiss authorities shall have access to the European databanks established under Article 12 of Directive 98/79/EC and Article 14a of Directive 93/42/EEC. They shall transmit to the Commission and/or body responsible for managing the databank the data provided for in those Articles collected in Switzerland for entry into the European databank.

European Community | 1. | Council Directive 92/42/EEC of 21 May 1992 on efficiency requirements for new hot-water boilers fired with liquid or gaseous fuels (OJ L 167, 22.6.1992, p. 17), as subsequently amended.

Switzerland | 100. | Ordinance of 16 December 1985 on Air Pollution Control (OAPC) (Annex 3 and 4) (RS 814.318.142.1), as subsequently amended.

European Community | 2. | Council Directive 90/396/EEC of 29 June 1990 on the approximation of the laws of the Member States relating to appliances burning gaseous fuels, as last amended by Council Directive 93/68/EEC of 22 July 1993 (OJ L 220, 30.8.1993, p. 1).

Switzerland | 101. | Federal Law of 19 March 1976 on the safety of technical installations and equipment (RO 1977 2370), as last amended on 18 June 1993 (RO 1995 2766).

102.

| Ordinance of 12 June 1995 on the safety of technical installations and equipment (RO 1995 2770), as last amended on 27 March 2002 (RO 2002 853).

103.

| Ordinance of 12 June 1995 on the procedures of conformity assessment of technical installations and equipment (RO 1995 2783).

The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established under Article 10 of this Agreement shall draw up and keep up to date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and the assessment criteria set out in Annex V to Directive 90/396/EEC.

European Community | 1. | Council Directive 84/525/EEC of 17 September 1984 on the approximation of the laws of the Member States relating to seamless, steel gas cylinders (OJ L 300, 19.11.1984, p. 1), as subsequently amended.

2.

| Council Directive 84/526/EEC of 17 September 1984 on the approximation of the laws of the Member States relating to seamless, unalloyed aluminium and aluminium alloy gas cylinders (OJ L 300, 19.11.1984, p. 20), as subsequently amended.

3.

| Council Directive 84/527/EEC of 17 September 1984 on the approximation of the laws of the Member States relating to welded unalloyed steel gas cylinders (OJ L 300, 19.11.1984, p. 48), as subsequently amended.

4.

| Council Directive 1999/36/EC of 29 April 1999 on transportable pressure equipment (OJ L 138, 1.6.1999, p. 20), as last amended by Commission Directive 2001/2/EC of 4 January 2001 (OJ L 005, 10.1.2001, p. 4), as subsequently amended.

Switzerland | 100. | No legislation relating to Directives 84/525/EEC, 84/526/EEC and 84/527/EEC.

101.

|

Relating to Directive 1999/36/EC:

Ordinance of 29 November 2002 on the transport of dangerous goods by road (RS 741.621) as subsequently amended.

Ordinance of 3 December 1996 on the transport of dangerous goods by rail (RS 742.401.6) as subsequently amended.

European Community | 5. | Council Directive 87/404/EEC of 25 June 1987 on the approximation of the laws of the Member States relating to simple pressure vessels (OJ L 220, 8.8.1987, p. 48), as last amended by Council Directive 93/68/EEC of 22 July 1993 (OJ L 220, 30.8.1993, p. 1).

6.

| Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment (OJ L 181, 9.7.1997, p. 1), as last amended by Regulation No 1882/2003 of the European Parliament and of the Council of 29 September 2003 (OJ L 284, 31.10.2003, p. 1).

Switzerland | 102. | Federal Law of 19 March 1976 on the safety of technical installations and equipment (RO 1977 2370), as last amended on 18 June 1993 (RO 1995 2766).

103.

| Ordinance of 20 November 2002 on the safety of simple pressure vessels (RO 2003 107).

104 | Ordinance of 20 November 2002 on the safety of pressure equipment (RO 2003 38).

The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established under Article 10 of this Agreement shall draw up and keep up to date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, the designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and the assessment criteria set out in Annex III to Directive 87/404/EEC, Annexes IV or V to Directive 97/23/EC or Annexes I, II or III to Directive 99/36/EC.

By way of derogation of Article 1(2) of this Agreement, both Parties shall recognise certificates and conformity marks on the compliance of transportable pressure vessels with Directive 99/36/EC which have been issued by conformity assessment bodies recognised in accordance with the procedure provided for in Article 11 of this Agreement.

It shall be sufficient for manufacturers, their authorised representatives or, where neither of these is present, the person responsible for placing products on the market to hold the technical documents required by the national authorities for inspection purposes at their disposal in the territory of one of the Parties for a period of at least 10 years after the last date of manufacture of the product.

The Parties hereby undertake to forward all relevant documents at the request of the authorities of the other Party.

European Community | 1. | Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity, as last amended by Regulation (EC) No 1882/2003 of the European Parliament and of the Council of 29 September 2003 (OJ L 284, 31.10.2003, p. 1).

2.

| Commission Decision 2000/299/EC of 6 April 2000 establishing the initial classification of radio equipment and telecommunications terminal equipment and associated identifiers (OJ L 97, 19.4.2000, p. 13).

3.

| Commission Decision 2000/637/EC of 22 September 2000 on the application of Article 3(3)(e) of Directive 1999/5/EC to radio equipment covered by the regional arrangement concerning radiotelephone service on inland waterways (OJ L 269, 21.10.2000, p. 50).

4.

| Commission Decision 2000/638/EC of 22 September 2000 on the application of Article 3(3)(e) of Directive 1999/5/EC to marine radio communication equipment intended to be fitted to seagoing non-SOLAS vessels and which is intended to participate in the global maritime distress and safety system (GMDSS) and not covered by Council Directive 96/98/EC on marine equipment (OJ L 269, 21.10.2000, p. 52).

5.

| Commission Decision 2001/148/EC of 21 February 2001 on the application of Article 3(3)(e) of Directive 1999/5/EC to avalanche beacons (OJ L 55, 24.2.2001, p. 65).

6.

| Commission Decision 2004/71/EC of 4 September 2003 on essential requirements relating to marine radio communication equipment which is intended to be used on non-SOLAS vessels and to participate in the Global Maritime Distress and Safety System (GMDSS) (OJ L 16, 23.1.2004, p. 54).

7.

| Commission Decision 2005/53/EC of 25 January 2005 on the application of Article 3(3)(e) of Directive 1999/5/EC of the European Parliament and of the Council to radio equipment intended to participate in the Automatic Identification System (AIS) (OJ L 22, 26.1.2005, p. 14).

8.

| Commission Decision 2005/631/EC of 29 August 2005 concerning essential requirements as referred to in Directive 1999/5/EC of the European Parliament and of the Council ensuring access of Cospas-Sarsat locator beacons to emergency services (OJ L 225, 31.8.2005, p. 28).

Switzerland | 100. | Federal Law of 30 April 1997 on Telecommunications (LTC); (RO 1997 2187), as last amended on 24 March 2006 (RO 2007 737 and 921).

101.

| Ordinance of 14 June 2002 on Telecommunications Equipment; (RO 2002 2086) as last amended on 16 April 2008 (RO 2008 1903).

102.

| Ordinance of 14 June 2002 of the Federal Office of Communications on Telecommunications Equipment (RO 2002 2111), as last amended on 17 September 2007 (RO 2007 4427).

103.

| Annex 1 to the Federal Office of Communications Ordinance on Telecommunications Equipment (RO 2002 2111), as last amended on 21 November 2005 (RO 2005 5139).

104.

| List of technical standards published in the Feuille Fédérale with titles and references, as last amended on 9 October 2007 (FF 2007 6431).

105.

| Ordinance of 9 March 2007 on Telecommunication Services (RO 2007 945).

The Committee established under Article 10 of this Agreement shall draw up and keep up to date, according to the procedure described in Article 11 of the Agreement, a list of the conformity assessment bodies.

The Committee established under Article 10 of this Agreement shall draw up and keep up to date a list of the designating authorities notified by the Parties.

For the designation of conformity assessment bodies, designating authorities shall comply with the general principles contained in Annex 2 to this Agreement and the assessment criteria set out in Annex VI to Directive 1999/5/EC.

Switzerland shall participate as observer in TCAM work and that of its subgroups.

The Parties shall notify each other of the authorities established on their territory responsible for carrying out the surveillance tasks involved in the implementation of their legislation as set out in Section I.

The Parties shall notify each other of their market surveillance activities within the bodies designated for this purpose.

The Parties shall inform each other of the interfaces they have regulated on their territory. When establishing the equivalence of notified interfaces and determining equipment class identifiers, the European Community shall take account of the interfaces regulated in Switzerland.

The Parties shall inform each other of interfaces offered on their territory by public telecommunications network operators.

When the Commission intends to adopt a decision to apply a requirement set in Article 3(3) of Directive 1999/5/EC, it shall consult Switzerland on the issue before submitting it formally to the Committee.

When Switzerland intends to adopt a technical and administrative regulation to apply a requirement set in Article 7.4 of the Ordinance on Telecommunications Equipment, it shall consult the Commission on the issue before submitting it formally to the Committee.

Where one of the Parties considers that apparatus declared to comply with its legislation causes serious damage to a network or radioelectric interference, or degradation of a network or its operation, and that Party has authorised the operator to refuse connection of the apparatus, disconnect it or withdraw it from service, it shall inform the other Party of this authorisation.

Where Switzerland considers that compliance with a harmonised standard does not guarantee that the essential requirements of its legislation as listed in Section I will be fulfilled, it shall inform the Committee and give its reasons.

The Committee shall consider the case and may ask the European Community to act in accordance with the procedure provided for in Article 5 of Directive 1999/5/EC. The Committee shall be informed of the result of the procedure.

This article is long: the rest is at the official publication.