8 SECTORAL ANNEX ON ELECTRICAL SAFETY, Agreement on mutual recognition between the European Community and Canada

In force

1.1. The purpose of this Annex is to establish a framework for the acceptance of electrical products through the recognition of conformity assessment carried out by bodies which comply with the requirements of the other Party, while maintaining the integrity of the safety system in each of the Parties.

1.2. This Annex also sets out procedures for the recognition of:

(a)

conformity assessment bodies (CABs) in Canada by the European Community (EC); and

(b)

CABs in the EC by Canada.

2.1. For access to the EC: the safety of electrical equipment falling within the scope of the Low Voltage Directive (Council Directive 73/23/EEC of 19 February 1973 as amended by Directive 93/68/EEC) [The categories of equipment and phenomena outside the scope of the Directive are: electrical equipment for use in an explosive atmosphere; electrical equipment for radiology and medical purposes; electrical parts for goods and passenger lifts; electricity meters; plugs and socket outlets for domestic use; electric fence controllers; radio-electrical interference; specialised electrical equipment, for use on ships, aircraft or railways, which complies with the safety provisions drawn up by international bodies in which Member States participate.].

2.2. For access to Canada: low voltage electrical equipment, including medical devices, covered by the Canadian Electrical Code, except for those products specifically excluded under the Low Voltage Directive (other than medical devices).

2.3. The legislative, regulatory and administrative requirements applicable in each Party and the regulatory authorities responsible for electrical safety are listed in Attachment 1.

3.1. Authorities set out in Attachment 2 are those organisations/public authorities responsible for assuring the competence and the control of CABs to certify electrical equipment in their territories to the requirements of the other Party.

4.1. The transitional arrangements shall operate for a term of eighteen (18) months from the time this MRA enters into force.

4.2. The purpose of the transition phase is to provide the responsible/designating authorities with an opportunity to build confidence and understanding of each other's procedures for recognising CABs and in the ability of those bodies to carry out their mandates. Successful completion of the transition phase should result in the determination by the responsible authorities that nominated CABs comply with the applicable criteria and are competent to conduct conformity assessment activities acceptable to the other Party.

4.3. During the transition phase, the authorities may jointly sponsor two seminars, one in Canada and one in the EC, concerning the relevant technical and product approval requirements.

5.1. During the transition phase, Canadian CABs shall accept test reports and related documents issued by nominated CABs in the other territory. For Community CABs, they must satisfy the following requirements:

(a)

be a participant in the International Electrotechnical Commission (IEC) scheme of the IECEE for recognition of results of testing to standards for safety of electrical equipment (certification bodies (CB) scheme) under the IEC system for conformity testing to standards for safety of electrical equipment (IECEE) as defined in IECEE Document 02/1992-05; or

(b)

have a contractual arrangement for acceptance of test data with a certification organisation accredited by the Standards Council of Canada.

5.2. During the transition phase, Community CABs will:

(a)

test products to Canadian requirements;

(b)

issue a comprehensive testing and evaluation file (i.e. assessment data, reports) for submission by the manufacturer of the tested products to a certification organisation in Canada.

5.3. Canadian certification organisations shall ensure that:

(a)

they inform the applicant and the Community CAB in a precise and complete manner of any deficiency;

(b)

they limit any request for additional information or samples to omissions, inconsistencies or variances from the technical regulations or standards; and

(c)

certification is done on the basis of existing procedures, including the application of their mark.

6.1. During the transition phase, the Joint Committee shall develop mutually acceptable mechanisms and procedures for marking of products to be exported to Canada in order to indicate their conformity with Canadian requirements. Such markings shall be under the control of CABs recognised by the responsible/designating authorities, provide for traceability, give sufficient information to consumers, and not give rise to confusion with other markings of conformity. For access to the EC market, the CE marking shall apply.

7.1. During the operational phase, the Parties will proceed to full mutual recognition of results of conformity assessment activities, as required under their respective legislation. CABs recognised by the responsible designating authorities shall operate as follows:

(a)

for access to the EC market:

if a product is challenged under the Low Voltage Directive, a report drawn up by a Canadian CAB recognised under this agreement shall be considered by the EC as if it were a report drawn up by a European notified body;

(b)

for access to the Canadian market:

CABs from the EC will be accredited in accordance with Standards Council of Canada (SCC) criteria for accreditation of certification bodies recognised in Canada and will be issued a certificate of accreditation. The following conditions are deemed to be equivalent to those prescribed criteria:

(i)

evidence of satisfactory performance in the transition phase; and

(ii)

accreditation by a European accreditation organisation according to applicable and relevant ISO/IEC guides adapted to Canadian and European conditions for accreditation of certification organisations; and

(iii)

evidence of procedures for follow-up of certification activities including the identification of a contact point responsible for initiating action with manufacturers of the products when necessary.

7.2. The Parties will encourage the establishment of mutual recognition agreements between the European accreditation organisations and the SCC.

7.3. Following the entry into force of the operational phase, the inclusion of additional CABs will be done in accordance with the rules set out in the Framework Agreement and in this Annex.

8.1. Upon request, a CAB may be required to provide additional documentary evidence to facilitate its passage from the transitional to the operational phase.

8.2. In the event that a proposal is made during, or at the end of the transition phase, requesting a responsible/designating authority to limit the scope of recognition of any designated CAB or to exclude it from the list of bodies accredited/designated, in accordance with the procedures outlined in the Framework Agreement, such a proposal shall be based on objective reasons and shall be properly documented in writing to the Joint Committee.

8.3. A CAB which has been granted limited recognition or has been denied recognition, may apply for re-evaluation after corrective action has been taken.

9.1. The authorities in each Party (see Attachments 1 and 2) retain the right to question the performance of CABs operating in the context of this Annex. (Upon reasoned request, the authorities in one Party may request a copy of the certification report prepared to its requirements in the territory of the exporting Party. This report shall be provided promptly and without charge.)

9.2. CABs shall have in place a plan of action with their certification clients, for enabling the withdrawal of non-conforming or hazardous products from the market place. That plan shall identify a contact point responsible for initiating action with manufacturers of the products in question.

10.1. The Joint Committee established under the Mutual Recognition Agreement shall appoint a Joint Electrical Safety Group (JESG).

10.2. The Group (JESG) shall consist of an equal number of representatives from Canada and the EC.

10.3. The Group may review issues of concern to either Party and no one shall refuse a request by the other to address such issues.

10.4. The Group may issue recommendations to the Joint Committee regarding concerns raised by the representatives of either Canada or the EC.

10.5. The Group shall establish its own rules of procedures, and take its decisions and adopt its recommendations by consensus of the Parties.