, The Road Vehicles (Approval) Regulations 2020

In forcesince 1 Sep 2020

Column 1Requirement | Column 2Definitions and supplementary provisions | Column 3Exemptions and modifications

1 Noise

The technical provisions of Annex I to Directive 70/157/EEC as last amended by Directive 1999/101/EC. | A “Stationary Noise Test” means, in the case of a modified exhaust system, a stationary test as defined in paragraphs 5.2.3.4.2 and 5.2.3.4.3 of Annex I to Directive 70/157/EEC with a noise limit value measured on the dB(A) scale which must not exceed the equivalent stationary value recorded on the approval, certificate of conformity or test report for that vehicle by more than 2dB(A) at 0.5m. | 1 Does not apply to category O vehicles.

2 Directive 70/157/EEC, Annex I, paragraphs 5.3.1.1, 5.3.1.2. and 5.3.1.3 do not apply.

3 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

4 If an approval or test report is issued for a vehicle in accordance with column 1 and the exhaust system is subsequently modified after the last silencer by not more than 2m in length, no further test is required. In the case of any other modification relating to the requirements of column 1 and affecting only the exhaust system, a Stationary Noise Test must be conducted.

5 In the case of a mobile crane Directive 70/157/EEC as amended by Directive 1999/101/EC applies and for point 5.2.2.1 of Annex I the following limit values are applicable—

81 dB(A) for vehicles with an engine power of less than 75 kW;

83 dB(A) for vehicles with an engine power of not less than 75 kW but less than 150 kW;

84 dB(A) for vehicles with an engine power of not less than 150 kW.

2 Light Duty Emissions

1 The technical provisions of Regulation (EC) 715/2007 as last amended by Regulation (EC) 692/2008, Annex I, Table 2. | “OBD” means On-Board Diagnostic systems. | 1 Does not apply to category M3, N3 or O vehicles.

2 Complete or completed vehicles manufactured after 1st March 2020: the technical provisions of Annex XXI in Commission Regulation (EU) 2017/1151 (WLTP). | 2 Vehicles of category M2 are exempt from the requirements of OBD.

3 Does not apply to vehicles approved to item 41.

4 Modification of exhaust system length after the last silencer is permissible without any further test.

5 In the case of a completed vehicle, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

6 An approval issued to the most representative base vehicle remains valid irrespective of change in reference weight or aerodynamic performance.

7 In the case of armoured vehicles exemption from one or more of the provisions in column 1 is permissible where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

3A Fuel Tanks

1 The technical provisions of Directive 70/221/EEC as last amended by Directive 2006/20/EC. | |

2 For vehicles using gaseous fuels:

UNECE Regulation 67.01 for LPG,

UNECE Regulation 110 for CNG,

UNECE Regulation 115 for LPG or CNG retro-fit, or

the technical provisions of Regulation (EC) No 79/2009 or UNECE Regulation 134 for hydrogen.

3B Rear Protective Devices

The technical provisions of paragraph 5 of Annex II to Directive 70/221/EEC as last amended by Directive 2006/20/EC. | | The requirement in column 1 does not apply to category O1 or O2 vehicles.

4 Rear Registration Plate Space

The technical provisions of Directive 70/222/EEC,

or

space must be provided for a registration plate meeting the requirements of the Road Vehicles (Display of Registration Marks) Regulations 2001.

5 Steering Effort

The technical provisions of paragraphs 4 and 5 of Annex I to Directive 70/311/EEC as last amended by Directive 1999/7/EC. | | 1 The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

2 A mobile crane may be fitted with a crab steering system.

6 Door latches and Hinges

The technical provisions of Directive 70/387/EEC as last amended by Directive 2001/31/EC, Annex I, Paragraph 3, and where the maximum mass exceeds 7.5 tonnes, Annex III. | | 1 Does not apply to category M2, M3 or O vehicles.

2 In the case of a mobile crane exemption from one or more of the provisions in column 1 is permissible where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

7 Audible Warning

Component:

Directive 70/388/EEC as last amended by Directive 87/354/EC.

1 Does not apply to category O vehicles.

2 In the case of an armoured vehicle—

(a)

exemption from one or more of the provisions in column 1 is permissible where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply, and

(b)

additional panic alarm devices are permitted.

Vehicle:

The technical provisions of paragraph 2 of Annex I to Directive 70/388/EEC as last amended by Directive 87/354/EC.

8 Indirect Vision

Component:

Directive 2003/97/EC.

1 Does not apply to category O vehicles.

Vehicle:

1 The technical provisions of

Directive 2003/97/EC Annex III.

2 Field of view requirements do not apply to optional mirrors.

3 In the case of a completed vehicle, the requirements according to the category of the base or incomplete vehicle based on maximum mass apply.

2 N2 and N3 vehicles manufactured after 1st April 2016: the technical provisions of paragraph 15 of UNECE Regulation 46.04. | 4 In the case of an armoured vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

5 The vehicle requirements in column 1 paragraph 2 do not apply to vehicles where any part of the Class V mirror is less than 2.4m above the ground.

6 The requirements in column 1 paragraph 2 do not apply to vehicles where the incomplete vehicle is of a type that is type approved to Directive 2003/97/EC.

9 Braking

The technical provisions of paragraph 2 of Annex I to Directive 71/320/EEC as last amended by Directive 98/12/EC and tests as defined in associated Annexes as may be applicable. | | 1 Does not apply to category O1 vehicles except where a braking system is fitted.

2 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

3 In the case of a mobile crane with more than 4 axles derogations are permitted provided that—

(a)

they are justified by the particular construction, and

(b)

all the braking performances relating to parking, service and secondary braking are fulfilled.

10 Electro-magnetic Compatibility

Component:

Directive 72/245/EEC as last amended by Directive 2006/28/EC.

“Installation Check” means a manufacturer's declaration that installed components are compliant with the requirements of column 1 and inspection of a sample of installed components as the approving authority deem necessary. |

Vehicle:

The technical provisions of: Directive 72/245/EEC as last amended by Directive 2006/28/EC, section 6 of Annex I taking into consideration the exemptions in section 8 and tests specified in Annexes IV to X,

or

an Installation Check.

13 Anti-Theft and Immobiliser

1 The technical provisions of: Directive 74/61/EEC as last amended by Directive 95/56/EC. | Immobilisers must be approved as part of the base vehicle or as a separate technical unit. | 1 Does not apply to category O vehicles.

2 Optional panic alarm not forming part of an alarm system under paragraph 1 must comply with the following—

(a)

the alarm signal must be audible and in addition may include optical alarm devices, or be a radio alarm, or any combination of the above;

(b)

the technical requirements of Directive 74/61/EEC as last amended by Directive 95/56/EC, Annex VI, Part II, paragraphs 8.2 to 8.8, 9.1.2 to 9.2.1, 9.2.3 to 9.4, 9.6, 9.9 to 9.10, and 9.11.2 to 11 inclusive;

(c)

unsetting the panic alarm must immediately cut the alarm signal.

Alarms, except those under column 1 paragraph 2, must be approved as part of the base vehicle or as a separate technical unit. | 2 The provisions of column 1 apply only to the extent that a device to prevent unauthorised use, immobiliser, alarm system or panic alarm is fitted.

3 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

15 Seat Strength

1 The technical provisions of Directive 74/408/EEC as last amended by Directive 2005/39/EC. | | 1 Does not apply to category O vehicles.

2 In the case of a motor caravan, ambulance, hearse, mobile crane, or other special purpose vehicle the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.

3 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

4 The provisions of paragraph 2 of Article 1 to Directive 2005/39/EC do not apply.

5 The provisions of paragraph 4.5 of Annex III to Directive 74/408/EEC as amended by Directive 2005/39/EC shall also apply to category M2 vehicles.

17 Speedometer and Reverse Gear

The technical provisions of Directive 75/443/EEC as last amended by Directive 97/39/EC, Annex I and Annex II, paragraphs 4.1 and 4.2. | | 1 Does not apply to category O vehicles.

2 This requirement does not apply to a vehicle fitted with a tachograph if the tachograph provides adequate visual indication of speed to the driver.

18 Plates (statutory)

The technical provisions of: Directive 76/114/EEC as last amended by Directive 78/507/EEC,

and

where the vehicle is the subject of a multi stage build a plate is required on completion of each stage as appropriate.

19 Seat Belt Anchorages

The technical provisions of Directive 76/115/EEC as last amended by Directive 2005/41/EC. | | 1 Does not apply to category O vehicles.

2 Does not apply to category M2 (Class A, I or II) or M3 (Class A, I or II) vehicles except where seat belt anchorages are fitted.

3 In the case of a motor caravan, ambulance, hearse, mobile crane, or other special purpose vehicle the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.

4 In the case of a motor caravan, ambulance, or hearse, at least anchorages for lap belts are required for all rear seating positions.

5 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

6 In the case of an armoured vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

20 Installation of Lighting and Light Signalling Devices

The technical provisions of UNECE Regulation 48.03,

and

dipped beam headlamps must be suitable for left hand rule of the road traffic.

1 In the case of a motor caravan, ambulance, hearse, armoured vehicle, mobile crane, or other special purpose vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply provided that all mandatory lighting devices are fitted and, except in the case of a mobile crane, that the geometric visibility is not affected.

2 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply to the cab.

3 Optional lamps meeting the technical requirements applicable to equivalent mandatory devices (except where specified otherwise) may be fitted, in addition to the mandatory and optional devices permitted by UNECE Regulation 48.03, as follows—

(a)

two additional dipped beam headlamps forming a matched pair with electrical connections that permit only one pair to operate at any one time and fitted to—

(i)

a vehicle intended for use in both left hand and right hand rule of the road traffic and in which case one pair must meet the requirements for right hand rule of the road traffic, or

(ii)

a special purpose vehicle designed for use with equipment that may obstruct the mandatory devices and fitted at a height not exceeding 1800mm,

(b)

any number of—

(i)

front position lamps,

(ii)

rear position lamps,

(iii)

stop lamps of category S1 or S2,

(iv)

end outline marker lamps,

(v)

rear retro-reflectors, or

(vi)

front retro-reflectors,

for which the requirements for position and geometric visibility do not apply, and

(c)

two rear direction indicator lamps.

4 The mandatory requirements of UNECE Regulation 48.03, paragraph 6.18.1 do not apply to trailers constructed for the carriage and launching of boats.

5 Amber side marker lamps may be wired to flash, provided that this flashing is in phase and at the same frequency with the direction indicator lamps at the same side of the vehicle.

6 The requirements of paragraphs 6.5.4.2 and 6.5.5 of UNECE Regulation 48.03 do not apply to any optional rear direction indicator lamps.

21 Retro Reflectors, Rear Marker Plates and Conspicuity Markings

For retro reflectors:

UNECE Regulation 3 or UNECE Regulation 150.

The fitting of conspicuity markings is optional for category M2, M3, O1 or O2 vehicles.

For conspicuity markings:

UNECE Regulation 104.

22 End-outline, Front-Position (side), Rear-Position (side), Stop, Side Marker, Daytime Running Lamps

UNECE Regulation 7 or UNECE Regulation 148. | |

23 Direction Indicators

UNECE Regulation 6 or UNECE Regulation 148. | |

24 Rear Registration Plate Lamps

UNECE Regulation 4 or UNECE Regulation 148. | |

25 Headlamps (including bulbs)

UNECE Regulation 8, UNECE Regulation 20, UNECE Regulation 31, UNECE Regulation 98, UNECE Regulation 112, UNECE Regulation 123 or UNECE Regulation 149. | | Does not apply to category O vehicles.

25A Cornering Lamps (where fitted)

UNECE Regulation 119 or UNECE Regulation 149. | | Does not apply to category O vehicles.

26 Front Fog Lamps (where fitted)

UNECE Regulation 19 or UNECE Regulation 149. | | Does not apply to category O vehicles.

27 Towing Hooks

The technical provisions of: Annex II to Directive 77/389/EEC as last amended by Directive 96/64/EC. | | 1 Does not apply to category O vehicles.

2 In the case of an armoured vehicle, mobile crane, or other special purpose vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

3 In the case of a motor caravan, ambulance, or hearse, the requirements apply only to the front of the vehicle.

28 Rear fog Lamps

UNECE Regulation 38 or UNECE Regulation 148. | |

29 Reversing Lamps

UNECE Regulation 23 or UNECE Regulation 148. | | Does not apply to category O1 vehicles except where fitted.

30 Parking Lamps (where fitted)

UNECE Regulation 7 or UNECE Regulation 148. | | Does not apply to category O vehicles.

31 Seat Belts

The technical provisions of Directive 77/541/EEC as last amended by Directive 2005/40/EC. | | 1 Does not apply to category O vehicles.

2 In the case of a motor caravan, ambulance, hearse, mobile crane, or other special purpose vehicle the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.

3 In the case of a motor caravan, ambulance, or hearse, at least lap belts are required for all rear seating positions.

4 In the case of a motor caravan, ambulance or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

5 In the case of an armoured vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

6 Seat belts which have been specially designed or adapted for use by an adult or young person suffering from some physical or mental impairment and intended for use solely by such person are exempt.

(Note: Seat belt anchorages for such belts must satisfy the requirements of item 19.)

7 Vehicles constructed or adapted for the secure transport of persons are required to be fitted with seat belts for the driver's and any front passenger's seat. Any other optional seat belts fitted must also comply.

8 A seat belt bearing an approval mark in accordance with column 1 may be fitted, whether or not the seat belt has been type approved for the anchorages to which it is fitted, provided that the seat belt complies with the installation requirements of column 1.

33 Identification of Controls, Tell-tales and Indicators

The technical provisions of paragraph 5 of Annex I to Directive 78/316/EEC as last amended by Directive 94/53/EC. | | Does not apply to category O vehicles.

34 Defrost/Demist

Vehicles must be fitted with an adequate defrosting and demisting device. | “Adequate” means sufficiently effective to ensure adequate visibility through the windscreen under all conditions. | Does not apply to category O vehicles.

35 Wash/Wipe

Vehicles must be fitted with adequate washing and wiping devices. | “Adequate” means sufficiently effective to ensure adequate visibility through the windscreen under all conditions. | Does not apply to category O vehicles.

36 Heating Systems (where fitted)

The technical provisions of Directive 2001/56/EC as last amended by Directive 2006/119/EC, paragraph 3 of Annex II, and Annexes III, VII and VIII. | |

41 Heavy Duty Emissions

1 Directive 2005/55/EC as last amended by Directive 2006/51/EC, Annex I, and Row B2 limit values. | | 1 Does not apply to category O vehicles.

2 Complete or completed vehicles manufactured on or after 1st September 2018: Regulation (EC) No 595/2009 Annex I limit values. | 2 Does not apply to vehicles approved under item 2.

3 Modification of exhaust system length after the last silencer is permissible without any further test.

4 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

5 Does not apply to—

(a)

mobile cranes which have an engine meeting the technical requirements of Regulation (EU) No 2016/1628 , or

(b)

vehicles designed to tow combinations exceeding 200 tonnes which have an engine meeting the technical requirements of Regulation (EU) No 2016/1628.

42 Lateral Protection (Side Guards)

The technical provisions of paragraphs 1 to 4 of Directive 89/297/EEC . | | Does not apply to category M2, M3, O1 or O2 vehicles.

43 Spray Suppression Systems

Component:

Directive 91/226/EEC .

1 Does not apply to category M2, M3, O1 or O2 vehicles or to category N2 vehicles with a maximum mass not exceeding 7.5 tonnes.

Vehicle:

The technical provisions of Directive 91/226/EEC.

2 Except where fitted, the requirements do not apply to “off-road” vehicles as defined in the Type Approval Regulation or to vehicles in which the presence of spray-suppression devices is incompatible with their use.

45 Safety glass

Component:

Directive 92/22/EEC as last amended by Directive 2001/92/EC.

1 Exclusions defined in paragraph 1 of Annex II to Directive 92/22/EEC as amended.

2 Directive 92/22/EEC, Annex III, paragraph 2.1.1 and 2.1.2 do not apply provided that driver's forward vision is not distorted and that light transmission of at least 70% is maintained.

Vehicle:

The technical provisions of: Directive 92/22/EEC as last amended by Directive 2001/92/EC.

3 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

4 In the case of a motor caravan, ambulance, hearse, mobile crane, or other special purpose vehicle, the requirements for all window glazing, other than the driver's cab glazing (windshield and side glazing), the material may be either safety glass or rigid plastic glazing.

5 This item does not apply to armoured vehicles.

46 Tyres

Component:

Directive 92/23/EEC as last amended by Directive 2005/11/EC.

1 In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

Vehicle:

The technical provisions of: Directive 92/23/EEC as last amended by Directive 2005/11/EC.

2 In the case of an armoured vehicle, or mobile crane, save as required by paragraph 3, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

3 In the case of a mobile crane the provision in paragraph 2 above applies on condition that the requirements in ISO 10571—1995 (E) or ETRTO Standards Manual 1998 are fulfilled.

47 Speed Limiters

Component:

Directive 92/24/EC as last amended by Directive 2004/11/EC .

Does not apply to category O vehicles.

Vehicle:

The technical provisions of: sections 1, 2 and 7 of Annex I to Directive 92/24/EC as last amended by Directive 2004/11/EC.

48 Masses and Dimensions

The technical provisions of: Directive 97/27/EC as last amended by Directive 2003/19/EC, section 7 of Annex I. | | 1 Directive 97/27/EC, Annex I, paragraphs 7.3.3, 7.5, 7.9, 7.10 and 7.11 do not apply. In the case of a category M2 or M3 vehicle, for paragraph 7.3.3 substitute “maximum height 4.57m”.

2 Trailers for abnormal indivisible loads of exceptional length are exempt from Annex I, paragraph 7.3.1.

3 In the case of a semi-trailer which is designed to carry at least two other wheeled vehicles, in Annex I—

(a)

paragraph 7.3.1.4.1 is to be read as though, for “the limit laid down in section 1.6 of Annex I to Directive 96/53/EC”, there were substituted “ 12.5m ”,

(b)

paragraph 7.3.1.4.2 is to be read as though, for “2,04 m as per section 4.4 of Annex I to Directive 96/53/EC”, there were substituted “ 4.19m ”.

4 Exemptions from Annex I, paragraph 7.6:

(a)

an abnormal indivisible load vehicle;

(b)

a semi-trailer low loader;

(c)

a semi-trailer step-frame low loader.

5 In the case of a semi-trailer being a trailer designed to carry at least two other wheeled vehicles, Annex I, paragraph 7.6 applies save that any part of the semi-trailer forward of the transverse plane passing through the king pin may be ignored.

This article is long: the rest is at the official publication.