, The Road Vehicles (Approval) Regulations 2009 (revoked)

In forcesince 1 Jul 2018

1 Requirement | 2 Definitions and supplementary provisions | 3 Exemptions and modifications

1.

Noise

The technical provisions of Annex I to Directive 70/157/EEC as amended by Directive 1999/101/EC;

Or

For vehicles for which an approval or test report has been issued prior to modification of the exhaust system, a Stationary Noise Test is permitted.

A “Stationary Noise Test” means:

(a)

a stationary test as defined in paragraphs 3.2.5.3.1 and 3.2.5.3.2 of Annex 3 to UNECE Regulation 51with a noise limit value which must not exceed 99dB(A) at 0.5m;

and

(b)

in the case of vehicles having a maximum permissible mass exceeding 2800kg fitted with a modified air brake system, a test report in accordance with Annex 6 to UNECE Regulation 51 (except that this shall not apply if proprietary air brake silencers are fitted).

1.

Does not apply to O category vehicles.

2.

UNECE Regulation 51, Annex 5, paragraphs 1.1, 1.2, and 1.3 do not apply.

3.

In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

4.

If a vehicle is type approved in accordance with column 1 and the exhaust system is subsequently modified after the last silencer by not more than 2m in length, no further test is required.

5.

In the case of a mobile crane, Directive 70/157/EEC as amended by Directive 99/101/EC applies and for point 5.2.2.1 of Annex I the following limit values are applicable:

81 dB(A) for vehicles with an engine power of less than 75 kW

83 dB(A) for vehicles with an engine power of not less than 75 kW but less than 150 kW

84 dB(A) for vehicles with an engine power of not less than 150 kW.

2.

Light Duty Emissions

1.

Directive 70/220/EEC as amended by Directive 94/12/EC, Annex I, paragraph 5.

2.

Vehicles manufactured on or after 1st January 2001; Directive 70/220/EEC as amended by Directive 98/69/EC, Annex I.

3.

Vehicles manufactured on or after 1st January 2006; Directive 70/220/EEC as amended by Directive 98/69/ EC Annex I, paragraph 5 (Row B limits).

4.

Vehicles manufactured on or after 1st September 2012: Regulation (EC) No. 715/2007, Annex I, Table 1.

5.

Vehicles manufactured on or after 1st September 2016: Regulation (EC) No. 715/2007, Annex I, Table 2.

6.

Vehicles manufactured on or after 1st March 2020: Regulation (EU) No. 2017/1151 (WLTP).

“OBD” means: On-Board Diagnostic systems as defined in paragraph 2.13 of Annex I to Directive 70/220/EEC or paragraph 9 of Article 3 to Regulation (EC) No. 715/2007. |

1.

Does not apply to M3, N3 or O category vehicles.

2…

3.

Vehicles of category M2 are excepted from the requirements of OBD.

4.

Does not apply to vehicles approved to item 41.

5.

Modification of exhaust system length after the last silencer is permissible without any further test.

6.

In the case of a completed vehicle, the requirements according to the category and date of completion of the base or incomplete vehicles based on maximum mass may apply.

7.

An Approval issued to the most representative base vehicle remains valid irrespective of change in reference weight or aerodynamic performance.

8.

In the case of armoured vehicles exemption from one or more of the provisions in column 1 is permissible where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

3.

Fuel Tanks/Rear Protective Devices

For Fuel Tanks:

1.

The technical provisions of paragraphs 5 and 6 of Annex I to Directive 70/221/EEC as amended by directive 2006/20/EC;

And

2.

For vehicles using gaseous fuels:

Regulations 67.01 or 115 for LPG.

Regulation 110.00 or 115 for CNG.

The technical provisions of Regulation (EC) No. 79/2009 or UNECE Regulation 134 for hydrogen

For rear protective devices:

3.

The technical provisions of paragraph 5 of Annex II to Directive 70/221/EEC as amended by directive 2006/20/EC.

4.

As an alternative to the installation requirements of paragraph 3 for a rear protective device fitted to a vehicle, an Installation Check.

“Installation Check” means a check to confirm that the rear protective device as a separate technical unit is of a type:

(a)

for which an approval or test report has been issued;

or

(b)

which has been tested and witnessed by the approval authority;

or

(c)

for which calculations have been submitted to the satisfaction of the approval authority;

And

a visual inspection that the device has been correctly installed in accordance with the technical requirements in paragraph 4 of column 1.

1.

The requirement in column 1 for a rear protective device does not apply to O1 or O2 category vehicles.

2.

In the case of fuel tanks other than tanks for gaseous fuels:

(a)

tanks must comply with the requirements given in column 1 except that the approval or test report need not be for the same vehicle type; and

(b)

modifications to the pipework or relocation of a tank excluding modification of the tank, the cap/filler device or the venting device, may be accepted by the approval authority.

4.

Rear Registration Plate Space

The technical provisions of Directive 70/222/EEC;

Or

Space must be provided for a registration plate meeting the requirements of the Display of Registration Marks Regulations 2001 .

5.

Steering Effort

The technical provisions of paragraphs 4 and 5 of Annex I to Directive 70/311/EEC as amended by 1999/7/EC;

Or

In the case of a Manual or Power Assisted System, and where an approval or test report has been issued for that system prior to its modification, a test will be conducted to ensure no obvious defect or undue stiffness is evident.

“Manual or Power Assisted System” means: a system that will operate in the event of failure of any power supply or assistance. |

1.

The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

2.

A mobile crane may be fitted with a crab steering system.

6.

Door latches and Hinges

The technical provisions of Directive 70/387/EEC as amended by Directive 2001/31/EC, Annex I, Paragraph 3, and where the maximum mass exceeds 7.5 tonnes, Annex III. | |

1.

Does not apply to M2, M3 or O category vehicles.

2.

In the case of a mobile crane exemption from one or more of the provisions in column 1 is permissible where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

7.

Audible Warning

Component:

Directive 70/388/EEC as amended by 87/354/EC.

Vehicle:

The technical provisions of:

Paragraph 2 of Annex I to Directive 70/388/EEC as amended by 87/354/EC;

Or

An Installation Check.

An “Installation Check” means a check for the presence and operation of the device. |

1.

Does not apply to O category vehicles.

2.

In the case of an armoured vehicle:

(a)

exemption from one or more of the provisions in column 1 is permissible where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply; and

(b)

additional panic alarm devices are permitted.

8.

Indirect Vision

Component:

Directive 2003/97/EC.

Vehicle:

1.

The technical provisions of Directive 2003/97/EC Annex III.

2.

N2 and N3 vehicles manufactured after 1 April 2016: the technical provisions of paragraph 15 of UNECE Regulation 46.04.

The technical provisions of:

Directive 2003/97/EC, Annex III;

Or

An Installation Check.

“Installation Check” means a check that the devices required in column 1 are fitted, bear an appropriate approval mark, are securely attached to the vehicle so as to minimize the effects of vibration and that the field of view requirements are met. |

1.

Does not apply to O category vehicles.

2.

Field of view requirements do not apply to optional mirrors.

3.

In the case of a Completed vehicle, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

4.

In the case of an armoured vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

5.

The vehicle requirements in col 1 paragraph 2 do not apply to vehicles where any part of the Class V mirror is below 2.4m above the ground.

6.

The requirements in col 1 paragraph 2 do not apply to vehicles where the incomplete vehicle is of a type that is type approved to Directive 2003/97/EC.

9.

Braking

1.

The technical provisions of paragraph 2 of Annex I to Directive 71/320/EEC as amended by Directive 98/12/EC and tests as defined in associated Annexes as may be applicable.

2.

Category O2 trailers and O1 trailers fitted with an inertia type braking system may, as an alternative, comply with the following requirements:

(a)

technical reports to Directive 71/320/EEC, Annex VIII, Appendix 2 and 3;

(b)

a compatibility check to Annex VIII, Appendix 4;

(c)

the requirements of Annex I, paragraphs 2.2.2.9 and 2.2.2.10;

(d)

the technical requirements of Annex VIII, paragraphs 3.1, 3.2, 3.4 excluding drag force check;

(e)

a visual assessment to Annex VIII, paragraphs 4.1, and of the first sentence of paragraph 4.2;

(f)

a Park Brake Test.

A “Park Brake Test” means a test for O2 and (if fitted) O1 category trailers that the park brake meets the performance requirement of Directive 71/320/EEC, Annex II, paragraph 2.2.2. |

1.

Does not apply to O1 category vehicles except where a braking system is fitted.

2.

In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

3.

In the case of a mobile crane with more than 4 axles derogations are permitted provided that:

(a)

they are justified by the particular construction; and

(b)

all the braking performances relating to parking, service and secondary braking are fulfilled.

10.

Electro-magnetic Compatibility

Component:

Directive 72/245/EEC as amended by Directive 2006/28/EC.

Vehicle:

The technical provisions of: Directive 72/245/EEC as amended by Directive 2006/28/EC, section 6 of Annex I taking into consideration the exemptions in section 8 and tests specified in Annexes IV to X;

Or

An Installation Check.

“Installation Check” means a manufacturer's declaration that installed components are compliant with the requirements of column 1 and inspection of a sample of installed components as the approving authority deem necessary. |

…

… | … | …

13.Anti-Theft and Immobiliser

1.

The technical provisions of Directive 74/61/EEC as amended by Directive 95/56/EC.

2.

Optional panic alarm not forming part of an alarm system under paragraph 1 must comply with the following:

(a)

The alarm signal must be audible and in addition may include optical alarm devices, or be a radio alarm, or any combination of the above.

(b)

The technical requirements of Directive 74/61/EEC as amended by Directive 95/56/EC, Annex VI, Part II, paragraphs 8.2 to 8.8, 9.1.2 to 9.2.1, 9.2.3 to 9.4, 9.6, 9.9 to 9.10, and 9.11.2 to 11 inclusive.

(c)

unsetting the panic alarm must immediately cut the alarm signal.

Immobilisers must be approved as part of the base vehicle or as a Separate Technical Unit.

Alarms, except those under column 1 paragraph 2, must be approved as part of the base vehicle or as a separate technical unit.

An “Installation Check” means:

An inspection of installed components as the approving authority deem necessary and in the case of an Immobiliser or Alarm system a completed installation certificate except that a panic alarm fitted in accordance with column 1, paragraph 2, a test report is required.

1.

Does not apply to O category vehicles.

2.

The provisions of column 1 apply only to the extent that a device to prevent unauthorised use, immobiliser, alarm system or panic alarm is fitted.

3.

In the case of devices to prevent unauthorised use, an immobiliser or alarm system the manufacturer may issue a declaration of the device(s) fitted and that they comply with column 1, and in such case an Installation Check will be conducted.

4.

In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

15.

Seat Strength

The technical provisions of Directive 74/408/EEC as amended by Directive 2005/39/EC. | |

1.

Does not apply to O category vehicles.

2.

In the case of a motor caravan, ambulance, hearse, mobile crane, or other special purpose vehicle, the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.

3.

In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

4.

The provisions of paragraph 2 of Article 1 to Directive 2005/39/EC do not apply.

5.

The testing of seat anchorages need not be performed provided that the vehicle is designed to meet the strength characteristics equivalent to those needed to satisfy the requirements of this item.

17.

Speedometer and Reverse Gear

The technical provisions of Directive 75/443/EEC as amended by Directive 97/39/EC, Annex I and Annex II, paragraphs 4.1 and 4.2. | |

1.

Does not apply to O category vehicles.

2.

This requirement does not apply to a vehicle fitted with a tachograph if the tachograph provides adequate visual indication of speed to the driver

18.

Plates (statutory)

The technical provisions of Directive 76/114/EEC as amended by Directive 78/507/EEC;

And

Where the vehicle is the subject of a multi stage build a plate is required on completion of each stage as appropriate.

19.

Seat Belt Anchorages

The technical provisions of Directive 76/115/EEC as amended by Directive 2005/41/EC. | |

1.

Does not apply to O category vehicles.

2.

Does not apply to M2 (Class A, I or II) or M3 (Class A, I or II) category vehicles except where seat belt anchorages are fitted.

3.

In the case of a motor caravan, ambulance, hearse, mobile crane, or other special purpose vehicle, the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.

4.

In the case of a motor caravan, ambulance, or hearse, at least anchorages for lap belts are required for all rear seating positions.

5.

In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

6.

In the case of an armoured vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

7.

Paragraph 5 of Annex I to Directive 76/115/EEC does not apply to a vehicle provided that the anchorages are designed to meet the strength characteristics equivalent to those needed to satisfy the requirements of that paragraph.

20.

Installation of Lighting and Light Signalling Devices

The technical provisions of UNECE Regulation 48.03;

And

Dipped beam headlamps must be suitable for left hand rule of the road traffic.

1.

The requirements in column 1 is limited to the installation of approved components as appropriate to the location, of the requisite number, installed in the specified positions, with the required geometric visibility and that operate in accordance with the technical requirements in column 1.

2.

In the case of a motor caravan, ambulance, hearse, armoured vehicle, mobile crane, or other special purpose vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply provided that all mandatory lighting devices are fitted and, except in the case of a mobile crane, that the geometric visibility is not affected.

3.

In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply to the cab.

4.

Optional lamps meeting the technical requirements applicable to equivalent mandatory devices (except where specified otherwise) may be fitted, in addition to the mandatory and optional devices permitted by UNECE Regulation 48.03, as follows:

(a)

two additional dipped beam headlamps forming a matched pair with electrical connections that permit only one pair to operate at any one time and fitted to:

(i)

a vehicle intended for use in both left hand and right hand rule of the road traffic and in which case one pair must meet the requirements for right hand rule of the road traffic; or

(ii)

a special purpose vehicle designed for use with equipment that may obstruct the mandatory devices and fitted at a height not exceeding 1800mm;

(b)

any number of:

(i)

front position lamps;

(ii)

rear position lamps;

(iii)

stop lamps of category S1 or S2;

(iv)

end outline marker lamps;

(v)

rear retro-reflectors; or

(vi)

front retro-reflectors,

for which the requirements for position and geometric visibility do not apply; and

(c)

two rear direction indicator lamps.

5.

The mandatory requirements of UNECE Regulation 48.03, paragraph 6.18.1.do not apply to trailers constructed for the carriage and launching of boats.

6.

Amber side marker lamps may be wired to flash, provided that this flashing is in phase and at the same frequency with the direction indicator lamps at the same side of the vehicle.

7.

The requirements of paragraphs 6.5.4.2 and 6.5.5 of UNECE Regulation 48.03 do not apply to any optional rear direction indicator lamps.

21.

Retro Reflectors, Rear Marker Plates and Conspicuity Markings

1.

For retro reflectors:

Directive 76/757/EEC as amended by Directive 97/29/EC.

2.

For conspicuity markings:

UNECE Regulation 104.

The fitting of conspicuity markings is optional for M2, M3, O1 or O2 category vehicles.

22.

End-outline, Front-Position (side), Rear-Position (side), Stop, Side Marker, Daytime Running Lamps

Directive 76/758/EEC as amended by Directive 97/30/EC. | |

23.

Direction Indicators

Directive 76/759/EEC as amended by Directive 99/15/EC. | |

24.

Rear registration plate Lamps

Directive 76/760/EEC as amended by Directive 97/31/EC. | |

25.

Head-lamps (including bulbs)

Directive 76/761/EEC as amended by Directive 99/17/EC. | | Does not apply to O category vehicles.

25A. Cornering Lamps (if fitted)

UNECE Regulation 119. | | Does not apply to O category vehicles.

26.

Front Fog Lamps if fitted)

Directive 76/762/EEC as amended by Directive 99/18/EC. | | Does not apply to O category vehicles.

27.

Towing Hooks

The technical provisions of Annex II to Directive 77/389/EEC as amended by Directive 96/64/EC;

Or

An Installation Check.

“Installation Check” means a check to confirm the presence and that towing hooks are securely attached to major structural aspects of the vehicle. |

1.

Does not apply to O category vehicles.

2.

In the case of an armoured vehicle, mobile crane, or other special purpose vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

3.

In the case of a motor caravan, ambulance, or hearse, the requirements apply only to the front of the vehicle.

28.

Rear fog Lamps

Directive 77/538/EEC as amended by Directive 99/14/EC. | |

29.

Reversing Lamps

Directive 77/539/EEC as amended by Directive 97/32/EC. | | Does not apply to O1 category vehicles except where fitted.

30.

Parking Lamps (if fitted)

Directive 77/540/EEC as amended by Directive 99/16/EC. | | Does not apply to O category vehicles.

31.

Seat Belts

The technical provisions of Directive 77/541/EEC EEC as amended by Directive 2005/40/EC. | |

1.

Does not apply to O category vehicles.

2.

In the case of a motor caravan, ambulance, hearse, mobile crane, or other special purpose vehicle, the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.

3.

In the case of a motor caravan, ambulance, or hearse, at least lap belts are required for all rear seating positions.

4.

In the case of a motor caravan, ambulance, or hearse, the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.

5.

In the case of an armoured vehicle, exemption from one or more of the provisions in column 1 is permitted where it can be demonstrated to the satisfaction of the approval authority that the special purpose of the vehicle makes it impossible to fully comply.

6.

Seat belts which have been specially designed or adapted for use by an adult or young person suffering from some physical or mental impairment and intended for use solely by such person are exempt.

(Note: Seat belt anchorages for such belts must satisfy the requirements of item 19.)

7.

Vehicles constructed or adapted for the secure transport of prisoners are required to be fitted with seat belts for the driver's and any front passenger's seat. Any other optional seat belts fitted must also comply.

8.

A seat belt bearing an approval mark in accordance with column 1 may be fitted, whether or not the seat belt has been type approved for the anchorages to which it is fitted, provided that the seat belt complies with the installation requirements of column 1.

33.

Identification of Controls, Tell-tales and Indicators

The technical provisions of: paragraph 5 of Annex I to Directive 78/316/EEC as amended by Directive 94/53/EC. | | Does not apply to O category vehicles.

34.

Defrost/Demist

Vehicles shall be fitted with an adequate defrosting and demisting device. | “Adequate” means: sufficiently effective to ensure adequate visibility through the windscreen under all conditions. | Does not apply to O category vehicles.

35.

Wash/Wipe

Vehicles shall be fitted with adequate washing and wiping devices. | “Adequate” means: sufficiently effective to ensure adequate visibility through the windscreen under all conditions. | Does not apply to O category vehicles.

36.

Heating Systems (if fitted)

1.

The technical provisions of: Directive 2001/56/EC as amended by 2006/119/EC, section 3 of Annex II, and Annexes III, VII and VIII.

2.

Combustion heaters:

The provisions of paragraph 1 may be met by an approval or test report for the device and an Installation Check.

“Installation Check” means an inspection to confirm compliance with the installation requirements of column 1. |

40.

Engine power

The essential technical provisions of Directive 80/1269/EEC as amended by Directive 99/99/EC. | | Does not apply to O category vehicles.

41.

Heavy Duty Emissions

1.

Directive 88/77/EEC as amended by Directive 91/542/EEC Row B limit values.

2.

Vehicles manufactured on or after 1st October 2001: Directive 88/77/EEC as amended by Directive 1999/96/EC Row A limit values.

This article is long: the rest is at the official publication.