1 Requirement | 2 Definitions and supplementary provisions | 3 Exemptions and modifications
Noise
Directive 70/157/EEC, as amended by: Directive 92/97/EEC, Annex I, paragraph 5. | A “Stationary Noise Test” means, in the case of a modified exhaust system, a stationary test as defined in paragraphs 5.2.3.4.2 and 5.2.3.4.3 of Annex I to Directive 70/157/EEC with a noise limit value measured on the dB(A) scale which must not exceed the equivalent stationary value recorded on the approval, certificate of conformity or test report for that vehicle by more than 2dB(A) at 0.5m. |
Directive 70/157/EEC, Annex I, paragraphs 5.3.1.1, 5.3.1.2 and 5.3.1.3 does not apply.
The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.
Where evidence of compliance has been provided, subsequent modification to the exhaust system will be permitted provided:
it is downstream of any emissions control device (e.g. a catalyst); and
the emission control device and silencer are identical to that fitted at the time compliance was demonstrated.
In the case of wheelchair accessible vehicles for which an approval or test report has been issued prior to modification of the exhaust system, a Stationary Noise Test is permitted.
Light Duty Emissions
Directive 70/220/EEC as amended by Directive 94/12/EC, Annex I, paragraph 5.
Vehicles manufactured on or after 1st January 2001: Directive 70/220/EEC as amended by Directive 98/69/EC, Annex I, paragraph 5 (Row A limits).
Vehicles manufactured on or after 1st January 2006: Directive 70/220/EEC as amended by Directive 98/69/EC Annex I, paragraph 5 (Row B limits).
Vehicles manufactured on or after 1st January 2012: Regulation (EC) 715/2007, Annex I, Table 1.
Vehicles manufactured on or after 1st September 2016: Regulation (EC) 715/2007 Annex I, Table 2.
Complete or Completed vehicles manufactured after 1st December 2018 in the case of M1 vehicles and 1st December 2019 otherwise: the technical provisions of Annex XXI to Regulation (EU) No. 2017/1151.
“OBD” means: On-Board Diagnostic systems as defined in paragraph 2.13 of Annex I to Directive 70/220/EEC or paragraph 9 of Article 3 to Regulation (EC) No. 715/2007. |
Vehicles are exempt from the requirements of OBD.
Does not apply to vehicles approved to item 41.
Modification of exhaust system length after the last silencer is permissible without any further test.
In the case of a Completed vehicle, the requirements according to the category and date of completion of the base or incomplete vehicle based on maximum mass may apply.
An Approval issued to the most representative base vehicle remains valid irrespective of change in the reference mass or aerodynamic performance.
In the case of wheelchair accessible vehicles:
the modification of the exhaust system is permitted without any further test provided the emission control devices including particulate filters (if any) are not affected; and
no new evaporative test is required on the modified vehicle on condition that the evaporative control devices are kept as fitted by the manufacturer of the base vehicle.
Diesel passenger vehicles manufactured before 1st January 2003 with a maximum permissible weight exceeding 2000kg, which have either more than 6 seats including the driver, or comply with the definition of an M1G (Off-Road vehicle as defined in Directive 2007/46/EC) are to be treated as a vehicle of category N1.
Braking
Vehicles manufactured on or after 1st October 1990: Directive 98/12/EC, Annex I, paragraph 2.1.1.3 (requirements for asbestos-free brake linings only).
Vehicles manufactured on or after 1st April 1995: Directive 71/320/EEC as amended by: Directive 91/422/EEC, Annex I, paragraph 2.
Vehicles manufactured on or after 31st March 2001: Directive 71/320/EEC as amended by: Directive 98/12/EC, Annex I, paragraph 2 (all requirements) and Annex II.
The requirements in column 1 for the driver to be able to operate the service braking system while keeping both hands on the steering control, and the secondary braking system while keeping at least one hand on the steering control, do not apply to a disabled person's vehicle, so long as the vehicle is adapted for a disabled driver to enable him to control the steering at all times while operating either braking system.
The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.
Evidence of compliance with column 1 remains valid where brake transmissions lines are repositioned.
Anti-Theft and Immobiliser
Vehicles manufactured on or after 1st October 1998: Directive 74/61/EEC, as amended by: Directive 95/56/EC, Annex V (electronic immobiliser), and Annex VI (alarm system). |
Immobilisers must be approved as part of the base vehicle or as a separate technical unit.
Alarms must be approved as part of the base vehicle or as a separate technical unit.
The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.
In the case of a panic alarm not forming part of an alarm system specified in column 1 the requirements of item 13 of Part 2 of this Schedule apply.
Protective Steering
Directive 74/297/EEC as amended by Directive 91/662/EEC, annex I, paragraphs 5 and 6. | |
This item does not apply to:
vehicles complying with the requirements of item 53;
vehicles of category N1with a maximum permissible mass exceeding 1500 kg.
The requirements of this item do not apply to a disabled persons' vehicle insofar as the adaptation prevents the vehicle from complying with any of the requirements of this item, except that this exemption does not apply where such adaptations can easily be removed, if necessary with the use of tools, and in which case evidence of compliance before the vehicle was adapted is required.
The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.
Seat Belt Anchorages
Directive 76/115/EEC as amended by Directive 90/629/EEC, annex I, paragraphs 4 and 5
Vehicles manufactured on or after 29th April 2009: Directive 76/115/EEC as amended by Directive 2005/41/EC
In the case of a wheelchair accessible vehicle the requirements of this item are substituted by item 19 of Part 2 of this Schedule.
In the case of other special purpose vehicles, the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.
In the case of a disabled person's vehicle adapted by a person other than the base vehicle manufacturer, any seat belt anchorage points fitted by that person may comply instead with the requirements of item 19 of Part 2 of this Schedule.
Seat Belts
Vehicles manufactured on or after 1st July 1997: Directive 77/541/EEC as amended by Directive 90/628/EEC, annex I, paragraphs 3.1 to 3.1.9 and 3.2.1 to 3.2.2.4.
Vehicles manufactured on or after 1st October 1999: Directive 77/541/EEC as amended by Directive 96/36/EC, annex I, paragraphs 3.1 to 3.1.10, 3.1.11, 3.1.12 and 3.2.1 to 3.2.2.5.
Vehicles manufactured on or after 29th April 2009: Directive 77/541/EEC as amended by Directive 2005/40/EC.
In the case of other special purpose, the requirements in column 1 do not apply to seats intended for use solely while the vehicle is stationary and any such seats must be clearly identified to users by means of a pictogram or a sign with appropriate text.
Seat belts which have been specially designed or adapted for use by an adult or young person suffering from some physical or mental impairment and intended for use solely by such person are exempt.
(Note: Seat belt anchorages for such belts must satisfy the requirements of item 19.)
A seat belt bearing an approval mark in accordance with column 1 may be fitted, whether or not the seat belt has been type approved for the anchorages to which it is fitted, provided that the seat belt complies with the installation requirements of column 1.
CO2 emissions/Fuel consumption
Vehicles manufactured on or after 1st January 1997: Directive 80/1268/EEC as amended by: Directive 93/116/EC, Annex I, paragraphs 4 to 7.
Vehicles manufactured on or after 1 Jan 2009: Directive 80/1268/EEC as amended by 2004/3/EC.
Does not apply to category N1 vehicles manufactured before 1st Jan 2009.
Does not apply where the applicant accepts a Combined CO2 figure determined by the Secretary of State using such information as he sees fit.
Vehicles with engines approved to item 41 are exempt.
Annexe V of Directive 89/491/EEC amending Directive 80/1268/EEC shall not apply with effect from 2nd January 2013.
Heavy Duty Emissions
Directive 88/77/EEC as amended by Directive 91/542/EEC Row B limit values.
Vehicles manufactured on or after 1st October 2001: Directive 88/77/EEC as amended by Directive 99/96/EC Row A limit values.
Vehicles manufactured on or after 1st October 2006: Directive 88/77/EEC as amended by Directive 99/96/EC Row B1 limit values.
Vehicles manufactured on or after 1st October 2009: Directive 88/77/EEC as amended by Directive 99/96/EC Row B2 limit values.
Complete or Completed vehicles manufactured on or after 1st September 2018: Regulation No. (EC) No. 595/2009 Annex I limit values.
Does not apply to vehicles approved to item 2.
In the case of a completed vehicle the requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.
Modification of exhaust system length after the last silencer is permissible without any further test.
Frontal impact
Vehicles manufactured on or after 1st October 2003: Directive 96/79/EC, Annex II, paragraph 3. | |
Category N1 vehicles and vehicles with a maximum mass exceeding 2500 kg are exempt.
The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.
For wheelchair accessible vehicles, and disabled person's vehicles, the vehicle is not required to comply in respect of an adaptation for a disabled person affecting the “frontal impact”. Evidence of compliance of the unadapted vehicle is required.
Side impact
Vehicles manufactured on or after 1st October 2003: Directive 96/27/EC, Annex II, paragraph 3. | |
Does not apply to vehicles where the R point of the lowest seat is more than 700mm above the ground.
The requirements according to the category of the base or incomplete vehicle based on maximum mass may apply.
For wheelchair accessible vehicles, and disabled person's vehicles, the vehicle is not required to comply in respect in respect of an adaptation for a disabled person affecting the “side impact”. Evidence of compliance of the unadapted vehicle is required.
Electrical Safety.
Vehicle: The technical provisions of UNECE Regulation 100.01 | |