1 ANNEX Methodology to determine the CO2 savings of Efficient Exterior LED Lights for use in certain light commercial vehicles, Decision_act (EU) 2020/1339

In forcesince 25 Feb 2021

This Annex sets out the methodology to determine the carbon dioxide (CO2) emission savings to be attributed to the use of efficient vehicle exterior LED lights in one or several of the exterior vehicle lights listed in Article 1, for use in the light commercial vehicles referred to in that Article.

In the case of NOVC-HEVs, the maximum available voltage level on board shall not exceed 60 Volt.

The testing conditions shall fulfil the requirements of UN/ECE Regulations Nos 4 [OJ L 4, 7.1.2012, p. 17.], 6 [OJ L 213, 18.7.2014, p. 1.], 7 [OJ L 285, 30.9.2014, p. 1.], 19 [OJ L 250, 22.8.2014, p. 1.], 23 [OJ L 237, 8.8.2014, p. 1.], 38 [OJ L 148, 12.6.2010, p. 55.], 48 [OJ L 323, 6.12.2011, p. 46.], 91 [OJ L 164, 30.6.2010, p. 69.], 100 [OJ L 302, 28.11.2018, p. 114.], 112 [OJ L 250, 22.8.2014, p. 67.], 119 [OJ L 89, 25.3.2014, p. 101.] and 123 [OJ L 222, 24.8.2010, p. 1.]. The power consumption shall be determined in accordance with point 6.1.4 of UN/ECE Regulation No 112, and points 3.2.1 and 3.2.2 of Annex 10 to that Regulation.

For the low beam adaptive front lighting system (AFS) falling within at least two of the Classes C, E, V or W as defined in Table 1 of UN/ECE Regulation No 123, the power consumption measurements shall be done at the LED intensity of each class (Pk), where k corresponds to each class specified at Table 1 as defined in UN/ECE Regulation No 123.

If it is agreed with the technical service that Class C is the representative/average LED intensity for the vehicle application, power consumption measurements shall be done in the same way as for any other exterior LED light included in the combination.

[Activation speeds shall be checked for each vehicle application in accordance with UN/ECE Regulation No 48 Section 6, Chapter 6.22, paragraphs 6.22.7.4.1 (class C), 6.22.7.4.2 (class V), 6.22.7.4.3 (class E), 6.22.7.4.4 (class W).]

Class | See point 1.3 and footnote 2 of UN/ECE Regulation No 123 | % LED Intensity | Activation Mode

C | Base Passing Beam (Country) | 100 |

50 km/h < speed < 100 km/h

Or when no mode of another passing beam class is activated (V, W, E)

V | Town | 85 | Speed < 50 km/h

E | Motorway | 110 | Speed > 100 km/h

W | Adverse Conditions | 90 | Windshield wiper active > 2 minutes

The following test equipment shall be used:

(a)

a power supply unit (i.e. variable voltage supplier);

(b)

two digital multimeters, one for measuring the DC-current, and the other for measuring the DC-voltage.

Figure 1 shows a possible test set-up, with the DC-voltage meter integrated in the power supply unit.

For each efficient exterior LED light included in a combination, the measurement of the current shall be performed at a voltage of 13,2 V. LED module(s) operated by an electronic light source control gear, shall be measured as specified by the applicant.

The manufacturer may request that additional measurements of the current shall be performed at other voltages, where the necessity to do so can be demonstrated on the basis of verified documentation.

In any case the measurements (n) shall be performed for each voltage at least five times consecutively. The applied voltage and the measured current shall be recorded in four decimals.

The power consumption shall be determined by multiplying the voltage with the measured current. The average of the power consumption for each efficient exterior LED light [W] shall be calculated as set out in Formula 1 with four decimals to be taken into account in the calculations. When a stepper motor or electronic controller is used for the supply of the electricity to the LED lamps, then the electric load of this component is to be excluded from the measurement.

where:

is the tested voltage of each LED vehicle light i [V]

is the measured current of each LED vehicle light i [A]

nis the number of measurements of the sample

jrefers to an individual measurement of power consumption

In case of low beam AFS, the power consumption [W] shall be calculated as the average of the LED power consumption for each class k, weighted according to the WLTP time share per speed range, in accordance with Formula 2.

where:

is the power consumption at the LED intensity for each class k as the average of n consecutive measurements [W]

Kis the number of classes associated with the low beam AFS.

WLTP_share is the WLTP time share per speed range in each class as defined in Table 2.

Speed range | WLTP_share

< 50 km/h | 0,588

50 – 100 km/h | 0,311

> 100 km/h | 0,101

When the low beam AFS does not fall within all four classes specified in Table 1, the WLTP_share of the missing classes shall be attributed to class C.

The power savings of each efficient exterior LED light (ΔPi) [W] shall be calculated in accordance with Formula 3.

where:

is the power consumption of the baseline vehicle light i [W]

is the average power consumption of the eco-innovative vehicle light i [W].

The power consumption of the different baseline vehicle lights is defined in Table 3.

Vehicle light | Power consumption PB [W]

Low beam headlamp | 137

High beam headlamp | 150

Front position | 12

Licence plate | 12

Front fog lamp | 124

Rear fog lamp | 26

Front turn signal lamp | 13

Rear turn signal lamp | 13

Reversing lamp | 52

Cornering lamp | 44

Static Bending lamp | 44

End-outline marker lamp (vehicles width > 2,1 m) | 12

Side marker lamp (vehicles length > 6 m) | 24

Rear position lamp | 12

The CO2 savings shall be calculated in accordance with Formula 4.

where:

vis the mean driving speed of the WLTP, which is 46,6 km/h

ηAis the efficiency of the alternator, which is 0,67

UFiis the usage factor of the vehicle light i as defined in Table 4

VPeis the consumption of effective power for each fuel approved, as defined in Table 5

CFis the fuel conversion factor as defined in Table 6.

Vehicle light | Usage factor (UF)

Low beam headlamp | 0,33

High beam headlamp | 0,03

Front position | 0,36

Licence plate | 0,36

Front fog lamp | 0,01

Rear fog lamp | 0,01

Front turn signal lamp | 0,15

Rear turn signal lamp | 0,15

Reversing lamp | 0,01

Cornering lamp | 0,019

Static Bending lamp | 0,039

End-outline marker lamps (width > 2,1 m) | 0,36

Side marker lamps (length > 6 m) | 0,36

Rear position lamp | 0,36

Type of Engine | Consumption of effective power VPe [l/kWh]

Petrol/E85 | 0,264

Petrol/E85 Turbo | 0,280

Diesel | 0,220

LPG | 0,342

LPG Turbo | 0,363

Consumption of effective power VPe [m3/kWh]

CNG (G20) | 0,259

CNG (G20) Turbo | 0,275

Type of fuel | Conversion factor (CF) [g CO2/l]

Petrol/E85 | 2330

Diesel | 2640

LPG | 1629

Conversion factor (CF) [g CO2/m3]

CNG (G20) | 1795

The uncertainty of the CO2 savings [W] shall be calculated in accordance with Formula 5 and shall not exceed 30 % of the CO2 savings.

where:

mis the number of exterior LED lights in the combination tested.

is the statistical margin of the power consumption of each i-th LED light fitted in the eco-innovative vehicle which shall be calculated in accordance with Formula 6.

In case of a low beam AFS the statistical margin of the power consumption [W] shall instead be calculated in accordance with Formulas 7 and 8.

where:

nis the number of power consumption measurements, which is at least 5 as indicated in Section 2.2.1

icorresponds to each vehicle light

jrefers to an individual measurement of power consumption

is the average of the n values of Pk

Kis the number of classes associated with the low beam AFS.

The CO2 savings and the uncertainty of the CO2 savings shall be rounded to two decimal places.

Each value used in the calculation of the CO2 savings shall either be applied unrounded or be rounded to the minimum number of decimal places which allows the maximum total impact (i.e. combined impact of all rounded values) on the savings to be lower than 0,25 g CO2/km.

The type-approval authority shall ensure for each version of a vehicle fitted with the efficient exterior LED lights that the minimum threshold criterion as specified in Article 9(1)(b) of Implementing Regulation (EU) No 427/2014 is met.

When verifying whether the minimum threshold criterion is met, the type-approval authority shall take into account, in accordance with Formula 9, the CO2 savings determined in point 3 and the uncertainty determined in point 4.

where:

MTis the minimum threshold equal to 0,5 g CO2/km

is the CO2 savings [g CO2/km] as defined in point 3

is the uncertainty of the CO2 savings calculated in accordance with point 4 [g CO2/km].

The CO2 savings to be certified by the type-approval authority in accordance with Article 11 of Implementing Regulation (EU) No 427/2014 [g CO2/km] are those calculated in accordance with Formula 10.

The CO2 savings shall be recorded in the type approval certificate for each vehicle version fitted with the efficient exterior LED lights.

where:

is the CO2 savings as determined in point 3 [g CO2/km]

is the uncertainty of the CO2 savings calculated in accordance with point 4 [g CO2/km].