Annex I (Part-21) to Regulation (EU) No 748/2012 is amended as follows:
the table of contents is replaced by the following:
point 21.A.14 is amended as follows:
point (a) is replaced by the following:
‘(a) An applicant for a type-certificate or restricted type-certificate shall demonstrate its capability by holding a design organisation approval, issued by the Agency in accordance with Subpart J.’;
point (c) is replaced by the following:
‘(c) By way of derogation from point (a), an applicant may demonstrate its capability by obtaining the Agency's acceptance of its certification programme established in accordance with point 21.A.15(b), where the product to be certified is:
an ELA1 aircraft; or
an engine or propeller installed in ELA1 aircraft.’;
point 21.A.15 is amended as follows:
points (b), (c) and (d) are replaced by the following:
‘(b) An application for a type-certificate or restricted type-certificate shall include, as a minimum, preliminary descriptive data of the product, the intended use of the product and the kind of operations for which certification is requested. In addition, it shall include, or be supplemented after the initial application, a certification programme for the demonstration of compliance in accordance with point 21.A.20, consisting of:
a detailed description of the type design, including all the configurations to be certified;
the proposed operating characteristics and limitations;
the intended use of the product and the kind of operations for which certification is requested;
a proposal for the initial type-certification basis, operational suitability data certification basis and environmental protection requirements, prepared in accordance with the requirements and options specified in points 21.B.80, 21.B.82 and 21.B.85;
a proposal for a breakdown of the certification programme into meaningful groups of compliance demonstration activities and data, including a proposal for the means of compliance and related compliance documents;
a proposal for the assessment of the meaningful groups of compliance demonstration activities and data, addressing the likelihood of an unidentified non-compliance with the type-certification basis, operational suitability data certification basis or environmental protection requirements and the potential impact of that non-compliance on product safety or environmental protection. The proposed assessment shall take into account at least the elements set out in subpoints (1) to (4) of point 21.B.100(a). Based on this assessment, the application shall include a proposal for the Agency's involvement in the verification of the compliance demonstration activities and data; and
a project schedule including major milestones.
After its initial submission to the Agency, the certification programme shall be updated by the applicant when there are changes to the certification project affecting any of the points 1 to 7 of point (b).
An application for a type-certificate or restricted type-certificate for an aircraft shall include, or be supplemented after the initial application, an application supplement for approval of the operational suitability data.’;
the following points (e) and (f) are added:
‘(e) An application for a type-certificate or restricted type-certificate for a large aeroplane or a large rotorcraft shall be valid for five years and an application for any other type-certificate or restricted type-certificate shall be valid for three years, unless the applicant demonstrates at the time of application that its product requires a longer time period to demonstrate and declare compliance and the Agency agrees to that longer time period.
In the case where a type-certificate or restricted type-certificate has not been issued, or it is evident that it will not be issued, within the time limit provided for in point (e), the applicant may:
submit a new application and comply with the type-certification basis, operational suitability data certification basis and environmental protection requirements, as established and notified by the Agency in accordance with points 21.B.80, 21.B.82 and 21.B.85 for the date of the new application; or
apply for an extension of the time period provided for in point (e) and propose a new date for the issuance of the type-certificate or restricted type-certificate. In that case, the applicant shall comply with the type-certification basis, operational suitability data certification basis and environmental protection requirements, as established and notified by the Agency in accordance with points 21.B.80, 21.B.82 and 21.B.85 for a date to be selected by the applicant. However, that date shall not precede the new date proposed by the applicant for the issuance of the type-certificate or restricted type-certificate by more than five years for an application for a type-certificate or restricted type-certificate for a large aeroplane or a large rotorcraft, and by more than three years for an application for any other type-certificate or restricted type certificate.’;
point 21.A.16A is deleted;
point 21.A.16B is deleted;
point 21.A.17A is deleted;
point 21.A.17B is deleted;
point 21.A.18 is deleted;
points 21.A.20 and 21.A.21 are replaced by the following:
Following the acceptance of the certification programme by the Agency, the applicant shall demonstrate compliance with the type certification basis, operational suitability data certification basis and environmental protection requirements, as established and notified to the applicant by the Agency in accordance with points 21.B.80, 21.B.82, 21.B.85, and shall provide the Agency with the means by which such compliance has been demonstrated.
The applicant shall report to the Agency any difficulty or event encountered during the process of demonstration of compliance that may have an appreciable effect on the risk assessment under point 21.A.15(b)(6) or on the certification programme, or may otherwise necessitate a change to the level of involvement of the Agency previously notified to the applicant in accordance with point 21.B.100(c).
The applicant shall record justifications of compliance within the compliance documents as referred to in the certification programme.
After completion of all demonstrations of compliance in accordance with the certification programme, including any inspections and tests in accordance with point 21.A.33, and after all flight tests in accordance with point 21.A.35, the applicant shall declare that:
it has demonstrated compliance with the type-certification basis, operational suitability data certification basis and environmental protection requirements, as established and notified by the Agency, following the certification programme as accepted by the Agency; and
no feature or characteristic has been identified that may make the product unsafe for the uses for which certification is requested.
The applicant shall submit to the Agency the declaration of compliance provided for in point (d). Where the applicant holds an appropriate design organisation approval, the declaration of compliance shall be made in accordance with Subpart J and submitted to the Agency.
In order to be issued a product type certificate or, when the aircraft does not meet the essential requirements of Annex II to Regulation (EU) 2018/1139 an aircraft restricted type certificate, the applicant shall:
demonstrate its capability in accordance with point 21.A.14;
comply with point 21.A.20;
demonstrate that the engine and propeller, if installed in the aircraft:
(A) have a type-certificate issued or determined in accordance with this Regulation; or
(B) have been demonstrated to be in compliance with the aircraft type-certification basis established and the environmental protection requirements designated and notified by the Agency as necessary to ensure the safe flight of the aircraft.
By derogation from point (a)(2), at the applicant's request included in the declaration referred to in point 21.A.20(d), the applicant is entitled to have the aircraft type-certificate or restricted type-certificate issued before the applicant has demonstrated compliance with the operational suitability data certification basis, provided that the applicant demonstrates such compliance before the date at which those data are to be actually used.’;
point 21.A.23 is deleted;
in point 21.A.31(a), point 4 is replaced by the following:
‘4. any other data allowing by comparison the determination of the airworthiness and, if relevant, the environmental characteristics of later products of the same type.’;
point 21.A.33 is replaced by the following:
(Reserved)
Before each test is undertaken during the demonstration of compliance required by point 21.A.20, the applicant shall have verified:
for the test specimen, that:
the materials and processes adequately conform to the specifications for the proposed type design;
the parts of the products adequately conform to the drawings in the proposed type design; and
the manufacturing processes, construction and assembly adequately conform to those specified in the proposed type design; and
for the test and measuring equipment to be used for the test, that those are adequate for the test and appropriately calibrated.
On the basis of the verifications carried out in accordance with point (b), the applicant shall issue a statement of conformity listing any potential non-conformity, together with a justification that this will not affect the test results, and shall allow the Agency to make an inspection it considers necessary to check the validity of that statement.
The applicant shall allow the Agency to:
review any data and information related to the demonstration of compliance; and
witness or carry out any test or inspection conducted for the purpose of the demonstration of compliance.
For all the tests and inspections witnessed or carried out by the Agency in accordance with point (d)(2):
the applicant shall submit to the Agency a statement of conformity provided for in point (c); and
no change that affects the validity of the statement of conformity shall be made to the test specimen, or the test and measuring equipment, between the time the statement of conformity provided for in point (c) was issued and the time the test specimen is presented to the Agency for test.’;
point 21.A.41 is replaced by the following:
The type-certificate and restricted type-certificate shall include the type design, the operating limitations, the type-certificate data sheet for airworthiness and emissions, the applicable type-certification basis and environmental protection requirements with which the Agency records compliance, and any other conditions or limitations prescribed for the product in the applicable certification specifications and environmental protection requirements. The aircraft type-certificate and restricted type-certificate shall include in addition the applicable operational suitability data certification basis, the operational suitability data and the type-certificate data sheet for noise. The aircraft type-certificate and restricted type-certificate data sheet shall include the record of CO2 emissions compliance and the engine type-certificate data sheet shall include the record of exhaust emissions compliance.’;
point 21.A.91 is replaced by the following:
Changes to a type-certificate are classified as minor and major. A “minor change” has no appreciable effect on the mass, balance, structural strength, reliability, operational characteristics, operational suitability data, or other characteristics affecting the airworthiness of the product or its environmental characteristics. Without prejudice to point 21.A.19, all other changes are “major changes” under this Subpart. Major and minor changes shall be approved in accordance with points 21.A.95 or 21.A.97, as appropriate, and shall be adequately identified.’
point 21.A.93 is replaced by the following:
An application for approval of a change to a type-certificate shall be made in a form and manner established by the Agency.
An application shall include, or be supplemented after the initial application, a certification programme for the demonstration of compliance in accordance with point 21.A.20, consisting of:
a description of the change identifying:
the configuration(s) of the product in the type certificate upon which the change is to be made;
all areas of the product in the type-certificate, including the approved manuals, that are changed or affected by the change; and
when the change affects the operational suitability data, any necessary changes to the operational suitability data;
an identification of any reinvestigations necessary to demonstrate compliance of the change and areas affected by the change with the type-certification basis, operational suitability data certification basis and environmental protection requirements; and
for a major change to a type-certificate:
a proposal for the initial type-certification basis, operational suitability data certification basis and environmental protection requirements, prepared in accordance with the requirements and options specified in point 21.A.101;
a proposal for a breakdown of the certification programme into meaningful groups of compliance demonstration activities and data, including a proposal for the means of compliance and related compliance documents;
a proposal for the assessment of the meaningful groups of compliance demonstration activities and data, addressing the likelihood of an unidentified non-compliance with the type-certification basis, operational suitability data certification basis or environmental protection requirements and the potential impact of that non-compliance on product safety or environmental protection. The proposed assessment shall take into account at least the elements set out in subpoints (1)–(4) of point 21.B.100(a). Based on this assessment, the application shall include a proposal for the Agency's involvement in the verification of the compliance demonstration activities and data; and
a project schedule including major milestones.
An application for a change to a type-certificate of a large aeroplane or a large rotorcraft shall be valid for five years and an application for a change to any other type-certificate shall be valid for three years. In the case where the change has not been approved, or it is evident that it will not be approved, within the time limit provided for in this point, the applicant may:
submit a new application for a change to the type-certificate and comply with the type-certification basis, operational suitability data certification basis and environmental protection requirements, as established by the Agency in accordance with point 21.A.101 and notified in accordance with point 21.B.105 for the date of the new application; or
apply for an extension of the time period provided for in the first sentence of point (c) for the original application and propose a new date for the issuance of the approval. In that case, the applicant shall comply with the type-certification basis, operational suitability data certification basis and environmental protection requirements, as established by the Agency in accordance with point 21.A.101 and notified in accordance with point 21.B.105, for a date to be selected by the applicant. However, that date shall not precede the new date proposed by the applicant for the issuance of the approval by more than five years for an application for a type-certificate or restricted type-certificate for a large aeroplane or a large rotorcraft, and by more than three years for an application for any other type-certificate or restricted type certificate.’;
points 21.A.95, 21.A.97 and 21.A.101 are replaced by the following:
Minor changes to a type-certificate shall be classified and approved by:
the Agency; or
an approved design organisation within the scope of its privileges provided for in points (1) and (2) of point 21.A.263(c), as recorded in the terms of approval.
A minor change to a type-certificate shall only be approved:
when it has been demonstrated that the change and areas affected by the change comply with the type-certification basis and the environmental protection requirements incorporated by reference in the type-certificate;
in the case of a change affecting the operational suitability data, when it has been demonstrated that the necessary changes to the operational suitability data comply with the operational suitability data certification basis incorporated by reference in the type-certificate;
when compliance with the type-certification basis that applies in accordance with point (1) has been declared and the justifications of compliance have been recorded in the compliance documents; and
when no feature or characteristic has been identified that may make the product unsafe for the uses for which certification is requested.
By derogation from point (1) in point (b), certification specifications which became applicable after those incorporated by reference in the type-certificate can be used for approval of a minor change, provided they do not affect the demonstration of compliance.
By derogation from point (a), at the applicant's request included in the declaration referred to in point 21.A.20(d), a minor change to an aircraft type-certificate may be approved before compliance with the operational suitability data certification basis has been demonstrated, provided that the applicant demonstrates such compliance before the date at which those data are actually used.
The applicant shall submit to the Agency the substantiation data for the change and a statement that compliance has been demonstrated in accordance with point (b).
An approval of a minor change to a type-certificate shall be limited to the specific configuration(s) in the type-certificate to which the change relates.
Major changes to a type-certificate shall be classified and approved by:
the Agency; or
an approved design organisation within the scope of its privileges provided for in points (1) and (8) of point 21.A.263(c), as recorded in the terms of approval.
A major change to a type-certificate shall only be approved:
when it has been demonstrated that the change and areas affected by the change comply with the type-certification basis and environmental protection requirements, as established by the Agency in accordance with point 21.A.101;
in the case of a change affecting the operational suitability data, when it has been demonstrated that the necessary changes to the operational suitability data meet the operational suitability data certification basis, as established by the Agency in accordance with point 21.A.101; and
when compliance with points (1) and (2) has been demonstrated in accordance with point 21.A.20, as applicable to the change.
By derogation from points (2) and (3) of point (b), at the applicant's request included in the declaration referred to in point 21.A.20(d), a major change to an aircraft type-certificate may be approved before compliance with the operational suitability data certification basis has been demonstrated, provided that the applicant demonstrates such compliance before the date at which those data are actually used.
An approval of a major change to a type-certificate shall be limited to the specific configuration(s) in the type-certificate to which the change relates.
A major change to a type-certificate and areas affected by the change shall comply with either the certification specifications applicable to the changed product on the date of the application for the change or certification specifications which became applicable after that date in accordance with point (f) below. The validity of the application shall be determined in accordance with point 21.A.93(c). In addition, the changed product shall comply with the environmental protection requirements designated by the Agency in accordance with point 21.B.85.
By derogation from point (a), an earlier amendment to a certification specification referred to in point (a) and to any other certification specification which is directly related may be used in any of the following situations, unless the earlier amendment became applicable before the date at which the corresponding certification specifications incorporated by reference in the type-certificate became applicable:
a change that the Agency finds not to be significant. In determining whether a specific change is significant, the Agency shall consider the change in the context of all previous relevant design changes and all related revisions to the applicable certification specifications incorporated by reference in the type-certificate for the product. Changes meeting one of the following criteria shall automatically be considered significant:
the general configuration or the principles of construction are not retained;
the assumptions used for certification of the product to be changed do not remain valid;
each area, system, part or appliance that the Agency finds not affected by the change;
each area, system, part or appliance that is affected by the change for which the Agency finds that compliance with the certification specifications referred to in point (a) does not contribute materially to the level of safety of the changed product or is impractical.
By derogation from point (a), in the case of a change to an aircraft other than a rotorcraft of 2722 kg (6000 lb) or less maximum weight, or to a non-turbine rotorcraft of 1361 kg (3000 lb) or less maximum weight, the change and areas affected by the change shall comply with the type-certification basis incorporated by reference in the type-certificate. However, if the Agency finds that the change is significant in an area, the Agency may require that the change and areas affected by the change comply with an amendment to a certification specification of the type-certification basis incorporated by reference in the type-certificate and with any other certification specification which is directly related, unless the Agency also finds that compliance with that amendment does not contribute materially to the level of safety of the changed product or is impractical.