1 ANNEX, Regulation (EU) 2019/621

In forcesince 17 Apr 2019
I.

For the purposes of this Annex, ‘instructions for the use of the electronic vehicle interface’ shall mean basic diagnostic information and fitment test information, in particular:

I.

1. Vehicle specific description of the location of and the access to the electronic vehicle interface.

I.

2. Information on whether the specific system supports diagnostic interaction (Yes/No). If yes:

I.

2.1. Vehicle-specific specification of bus types and protocols

I.

2.2. Vehicle-specific specification of the communication parameters of the inspected system/function

I.

3. Vehicle-specific information about the originally installed system.

II.

The vehicle technical information concerning L-category vehicles and vehicles outside the scope of Directive 2014/45/EU is indicated as guidance.

[Type-approved in accordance with Directive 70/220/EEC, Regulation (EC) No 715/2007, Annex I, Table 1 (Euro 5), Directive 88/77/EEC and Directive 2005/55/EC.] [Type-approved in accordance with Regulation (EC) No 715/2007, Annex I, Table 2 (Euro 6) and Regulation (EC) No 595/2009 (Euro VI).] [Type-approved in accordance with Directive 70/220/EEC, Annex I, Table 1 (Euro 5) to Regulation (EC) No 715/2007, Directive 88/77/EEC and Directive 2005/55/EC.] [Type-approved in accordance with Annex I, Table 2 (Euro 6) to Regulation (EC) No 715/2007, and Regulation (EC) No 595/2009 (Euro VI)]

Item | Method | Information needed | Category for which the information is needed

< 3,5 t | > 3,5 t | O | L | T

1.

BRAKING EQUIPMENT

1.1. Mechanical condition and operation

1.1.1. Service brake pedal/hand lever pivot

Visual inspection of the components while the braking system is operated.

Note: Vehicles with power-assisted braking systems should be inspected with the engine switched off.

1.1.2. Pedal/hand lever condition and travel of the brake operating device

Visual inspection of the components while the braking system is operated

Note: Vehicles with power-assisted braking systems should be inspected with the engine switched off.

1.1.3. Vacuum pump or compressor and reservoirs

Visual inspection of the components at normal working pressure. Check time required for vacuum or air pressure to reach safe working value and function of warning device, multi-circuit protection valve and pressure relief valve. |

Pressure/max. cut out – min. cut in [bar]

See UN R13 5.1.4.5.2

X | | |

Multi-circuit protection valve static closing pressure [bar]

See UN R13 5.1.4.5.2

X | | | X

1.1.4. Low pressure warning gauge or indicator

Functional check | | | | | |

1.1.5. Hand-operated brake control valve

Visual inspection of the components while the braking system is operated. | | | | | |

1.1.6. Parking brake activator, lever control, parking brake ratchet, electronic parking brake

Visual inspection of the components while the braking system is operated. | General description for electronic parking brake | X | X | | | X

1.1.7. Braking valves (foot valves, unloaders, governors)

Visual inspection of the components while the braking system is operated. | | | | | |

1.1.8. Couplings for trailer brakes (electrical & pneumatic)

Disconnect and reconnect braking system coupling between towing vehicle and trailer. | | | | | |

1.1.9. Energy storage reservoir pressure tank

Visual inspection. | | | | | |

1.1.10. Brake servo units, master cylinder (hydraulic systems)

Visual inspection of the components while the braking system is operated, if possible. | | | | | |

1.1.11. Rigid brake pipes

Visual inspection of the components while the braking system is operated, if possible. | | | | | |

1.1.12. Flexible brake hoses

Visual inspection of the components while the braking system is operated, if possible. | | | | | |

1.1.13. Brake linings and pads

Visual inspection. |

Method of assessing wear and wear limit

See UN R13 5.2.1.11.2 and 5.2.2.8.2.

X | X | X | X |

1.1.14. Brake drums, brake discs

Visual inspection. |

Method of assessing wear and wear limit

See UN R13 5.2.1.11.2 and 5.2.2.8.2.

X | X | X | |

1.1.15. Brake cables, rods, levers, linkages

Visual inspection of the components while the braking system is operated, if possible. | | | | | |

1.1.16. Brake actuators (including spring brakes or hydraulic cylinders)

Visual inspection of the components while the braking system is operated, if possible |

Brake cylinder type Service/Parking

Maximum stroke [mm]

Lever length [mm]

See UN R13 5.1.4.5.2

X | X | |

1.1.17. Load sensing valve

Visual inspection of the components while the braking system is operated, if possible. | Input pressure [bar] | | X | X | |

Output pressure for x % of maximum axle load [bar]

UN R 13 Annex 10 7.4 + Diagram 5

X | X | |

1.1.18. Slack adjusters and indicators

Visual inspection. |

Maximum stroke [mm]

See UN R13 5.1.4.5.2

X | X | |

working principle [automatic/manual adjusted] | | X | X | |

1.1.19. Endurance braking system (where fitted or required)

Visual inspection. | | | | | |

1.1.20. Automatic operation of trailer brakes

Disconnect brake coupling between towing vehicle and trailer. | | | | | |

1.1.21. Complete braking system

Visual inspection | | | | | |

1.1.22. Test connections (where fitted or required)

Visual inspection |

Location and identification of test connections

See UN R 13 5.1.4.2

X | X | |

Location and identification of test connections

See 2015/68 Annex I. 2.1.8.1

X

1.1.23. Overrun brake

Visual inspection and by operation | | | | | |

1.2 Service braking performance and efficiency

1.2.1. Performance

During a test on a brake tester or, if impossible, during a road test, apply the brakes progressively up to maximum effort. | Specific requirements for testing vehicle on a brake tester (test mode) | X | X | X | X | X

1.2.2. Efficiency

Test with a brake tester or, if one cannot be used for technical reasons, by a road test using a deceleration recording instrument to establish the braking ratio which relates to the maximum authorised mass or, in the case of semi-trailers, to the sum of the authorised axle loads.

Vehicles or a trailer with a maximum permissible mass exceeding 3,5 tonnes has to be inspected following the standards given by ISO 21069 or equivalent methods.

Road tests should be carried out under dry conditions on a flat, straight road.

Design system pressure for maximum load [bar]

See UN R13 5.1.4.5.2

X | X | |

Reference brake force [kN] at input pressure [bar] axle 1 | | X | X | |

Reference brake force [kN] at input pressure [bar] axle 2 | | X | X | |

Reference brake force [kN] at input pressure [bar] axle 3 | | X | X | |

Reference brake force [kN] at input pressure [bar] axle 4

See UN R13 5.1.4.6.2

X | X | |

Calculation pressure for each axle | | X | X | |

1.3. Secondary (emergency) braking performance and efficiency (if met by separate system)

1.3.1. Performance

If the secondary braking system is separate from the service braking system, use the method specified in 1.2.1. | General description of system including circuits (clear definition of the secondary brake) | X | X | | | X

1.3.2. Efficiency

If the secondary braking system is separate from the service braking system, use the method specified in 1.2.2. | | | | | |

1.4. Parking braking performance and efficiency

1.4.1. Performance

Apply the brake during a test on a brake tester. | General description of system including recommended test procedure if dynamic test (on brake tester or road test) not possible | X | X | X | |

1.4.2. Efficiency

Test with a brake tester. If not possible, then by a road test using either an indicating or deceleration recording instrument or with the vehicle on a slope of known gradient. | | | | | |

1.5. Endurance braking system performance

Visual inspection and, where possible, test whether the system functions. | General description | | X | | |

1.6. Anti-lock braking system (ABS)

Visual inspection and inspection of warning device and/or using electronic vehicle interface. | instructions for the use of the electronic vehicle interface | X | X | X | X | X

1.7. Electronic brake system (EBS)

Visual inspection and inspection of warning device and/or using electronic vehicle interface. | instructions for the use of the electronic vehicle interface | X | X | X | | X

1.8. Brake fluid

Visual inspection | | | | | |

2.

STEERING

2.1. Mechanical condition

2.1.1. Steering gear condition

With the vehicle over a pit or on a hoist and with the road wheels off the ground or on turntables, rotate the steering wheel from lock to lock. Visual inspection of the operation of the steering gear. | | | | | |

2.1.2. Steering gear casing attachment

With vehicle on a pit or hoist and the weight of the vehicle road wheels on the ground, rotate steering/handle bar wheel clockwise and anticlockwise or using a specially adapted wheel play detector. Visual inspection of the attachment of gear casing to chassis. | | | | | |

2.1.3. Steering linkage condition

With the vehicle over a pit or on a hoist and with the road wheel on the ground, rock steering wheel clockwise and anti-clockwise or using a specially adapted wheel play detector. Visual inspection of steering components for wear, fractures and security. | | | | | |

2.1.4. Steering linkage operation

With the vehicle over a pit or on a hoist and with the road wheel on the ground, rock steering wheel clockwise and anti-clockwise or using a specially adapted wheel play detector. Visual inspection of steering components for wear, fractures and security. | | | | | |

2.1.5. Power steering

Check steering system for leaks and hydraulic fluid reservoir level (if visible). With the road wheels on the ground and with the engine running, check that the power steering system is operating. | | | | | |

2.2. Steering wheel, column and handle bar

2.2.1. Steering wheel/handle bar condition

With the vehicle over a pit or on a hoist and the mass of the vehicle on the ground, push and pull the steering wheel in line with column, push steering wheel/handle bar in various directions at right angles to the column/forks. Visual inspection of play, and condition of flexible couplings or universal joints. | | | | | |

2.2.2. Steering column/yokes and forks and steering dampers

With the vehicle over a pit or on a hoist and the mass of the vehicle on the ground, push and pull the steering wheel in line with column, push steering wheel/handle bar in various directions at right angles to the column/forks. Visual inspection of play, and condition of flexible couplings or universal joints. | Steering damper fitted (YES/NO) | | | | X |

2.3. Steering play

With the vehicle over a pit or on a hoist, the mass of the vehicle on the road wheels, the engine, if possible, running for vehicles with power steering and with the road wheels in the straight-ahead position, lightly turn the steering wheel clockwise and anti-clockwise as far as possible without moving the road wheels. Visual inspection of free movement. | | | | | |

2.4. Wheel alignment (X)2

Check alignment of steered wheels with suitable equipment. | | | | | |

2.5. Trailer steered axle turntable

Visual inspection or using a specially adapted wheel play detector | | | | | |

2.6. Electronic Power Steering (EPS)

Visual inspection and consistency check between the angle of the steering wheel and the angle of the wheels when switching on/off the engine, and/or using the electronic vehicle interface | instructions for the use of the electronic vehicle interface | X | X | | |

3.

VISIBILITY

3.1. Field of vision

Visual inspection from driving seat. | | | | | |

3.2. Condition of glass

Visual inspection. | | | | | |

3.3. Rear-view mirrors or devices

Visual inspection. | | | | | |

3.4. Windscreen wipers

Visual inspection and by operation. | | | | | |

3.5. Windscreen washers

Visual inspection and by operation. | | | | | |

3.6. Demisting system (X)2

Visual inspection and by operation. | | | | | |

4.

LAMPS, REFLECTORS AND ELECTRICAL EQUIPMENT

4.1. Headlamps

4.1.1. Condition and operation

Visual inspection and by operation. | Category of light source […,…] | X | X | | X | X

4.1.2. Alignment

Determine the horizontal aim of each headlamp on dipped beam using a headlamp aiming device or using the electronic vehicle interface. | Alignment of dipped beam [per cent] for both vertical inclination and direction | X | X | | X |

instructions for the use of the electronic vehicle interface | X | X | | X |

For determining the horizontal aim by using the electronic vehicle interface information on the actuation of the headlamp beam movement to allow assessment of alignment | X | X | | X |

4.1.3. Switching

Visual inspection and by operation or using the electronic vehicle interface | instructions for the use of the electronic vehicle interface | X | X | | X |

4.1.4. Compliance with requirements1.

Visual inspection and by operation. | | | | | |

4.1.5. Levelling devices (where mandatory)

Visual inspection and by operation, if possible, or using the electronic vehicle interface. | Operation mode [manual/automatic) | X | X | | X |

instructions for the use of the electronic vehicle interface | X | X | | X |

4.1.6. Headlamp cleaning device (where mandatory)

Visual inspection and by operation if possible. | Device mandatory [Y/N] | X | X | | |

4.2. Front and rear position lamps, side marker lamps, end outline marker lamps and daytime running lamps

4.2.1. Condition and operation

Visual inspection and by operation. | Fitment of daytime running lamps, [Y/N] | X | X | | X |

4.2.2. Switching

Visual inspection and by operation. | | | | | |

4.2.3. Compliance with requirements1

Visual inspection and by operation. | | | | | |

4.3. Stop Lamps

4.3.1. Condition and operation

Visual inspection and by operation. | | | | | |

4.3.2. Switching

Visual inspection and by operation or using the electronic vehicle interface. | Fitment of emergency stop signal, [Y/N] | X | X | X | |

instructions for the use of the electronic vehicle interface | X | X | X | |

4.3.3. Compliance with requirements1.

Visual inspection and by operation. | | | | | |

4.4. Direction indicator and hazard warning lamps

4.4.1. Condition and operation

Visual inspection and by operation. | | | | | |

4.4.2. Switching

Visual inspection and by operation. | | | | | |

4.4.3. Compliance with requirements1.

Visual inspection and by operation. | | | | | |

4.4.4. Flashing frequency

Visual inspection and by operation. | | | | | |

4.5. Front and rear fog lamps

4.5.1. Condition and operation

Visual inspection and by operation. | | | | | |

4.5.2. Alignment (X)2

By operation and using a headlamp aiming device | | | | | |

4.5.3. Switching

Visual inspection and by operation. | | | | | |

4.5.4. Compliance with requirements1.

Visual inspection and by operation. | | | | | |

4.6. Reversing lamps

4.6.1. Condition and operation

Visual inspection and by operation. | | | | | |

4.6.2. Compliance with requirements1

Visual inspection and by operation. | | | | | |

4.6.3. Switching

Visual inspection and by operation. | | | | | |

4.7. Rear registration plate lamp

4.7.1. Condition and operation

Visual inspection and by operation. | | | | | |

4.7.2. Compliance with requirements1

Visual inspection and by operation. | | | | | |

4.8. Retro-reflectors, conspicuity (retro reflecting) markings and rear marking plates

4.8.1. Condition

Visual inspection. | | | | | |

4.8.2. Compliance with requirements1

Visual inspection. | | | | | |

4.9. Tell-tales mandatory for lighting equipment

4.9.1. Condition and operation

Visual inspection and by operation. | | | | | |

4.9.2. Compliance with requirements1

Visual inspection and by operation. | | | | | |

4.10. Electrical connections between towing vehicle and trailer or semi-trailer

Visual inspection: if possible examine the electrical continuity of the connection. | | | | | |

4.11. Electrical wiring

Visual inspection with vehicle over a pit or on a hoist, including inside the engine compartment (if applicable). | Wiring/cable identification (e.g. colour, shielding, cross section, size), insulation monitoring (high voltage) | X | X | | X |

Location of any high voltage wiring | X | X | | X |

4.12. Non obligatory lamps and retro-reflectors (X)2

Visual inspection and by operation. | | | | | |

4.13. Battery(ies)

Visual inspection. | Location of battery(ies) | X | X | | X | X

Number of batteries | X | X | | X | X

Special arrangements for high voltage batteries | X | X | | X |

Vehicle (VIN) specific information on battery switch [Y/N] | X | X | | X |

Vehicle (VIN) specific information on battery fuse [Yes/No] | X | X | | X |

Vehicle (VIN) specific information on battery ventilation [Yes/No] | X | X | | X |

Vehicle (VIN) specific information on operation principle | X | X | | X |

5.

AXLES, WHEELS, TYRES AND SUSPENSION

5.1. Axles

5.1.1. Axles

Visual inspection with vehicle over a pit or on a hoist. Wheel play detectors may be used and are recommended for vehicles having a maximum mass exceeding 3,5 tonnes | General description, number of axles | X | X | X | X | X

5.1.2. Stub axles

Visual inspection with vehicle over a pit or on a hoist. Wheel play detectors may be used and are recommended for vehicles having a maximum mass exceeding 3,5 tonnes. Apply a vertical or lateral force to each wheel and note the amount of movement between the axle beam and stub axle. | | | | | |

5.1.3. Wheel bearings

Visual inspection with the vehicle over a pit or on a hoist. Wheel play detectors may be used and are recommended for vehicles having a maximum mass exceeding 3,5 tonnes. Rock the wheel or apply a lateral force to each wheel and note the amount of upward movement of the wheel relative to the stub axle. | | | | | |

5.2. Wheels and tyres

5.2.1. Road wheel hub

Visual inspection. | | | | | |

5.2.2. Wheels

Visual inspection of both sides of each wheel with vehicle over a pit or on a hoist. | Wheel size/dimensions/offset | X | X | X | X | X

5.2.3. Tyres

Visual inspection of the entire tyre by either rotating the road wheel with it off the ground and the vehicle over a pit or on a hoist, or by rolling the vehicle backwards and forwards over a pit. | Tyre size, | X | X | X | X | X

load capacity, | X | X | X | X | X

speed category | X | X | X | X | X

Tyre pressure monitoring system [N/Y] direct/indirect | X | X | X | X | X

5.3. Suspension system

5.3.1. Springs and stabiliser

Visual inspection with vehicle over a pit or on a hoist. Wheel play detectors may be used and are recommended for vehicles having a maximum mass exceeding 3,5 tonnes | | | | | |

5.3.2. Shock absorbers

Visual inspection with vehicle over a pit or on a hoist or using special equipment, if available. | | | | | |

5.3.2.1 efficiency testing of damping (X)2

Use special equipment and compare left/right differences | | | | | |

5.3.3. Torque tubes, radius arms, wishbones and suspension arms

Visual inspection with vehicle over a pit or on a hoist. Wheel play detectors may be used and are recommended for vehicles having a maximum mass exceeding 3,5 tonnes | | | | | |

5.3.4. Suspension joints

Visual inspection with vehicle over a pit or on a hoist. Wheel play detectors may be used and are recommended for vehicles having a maximum mass exceeding 3,5 tonnes | | | | | |

5.3.5. Air suspension

Visual inspection | | | | | |

6.

CHASSIS AND CHASSIS ATTACHMENTS

6.1. Chassis or frame and attachments

6.1.1. General condition

Visual inspection with vehicle over a pit or on a hoist. | | | | | |

6.1.2. Exhaust pipes and silencers

Visual inspection with vehicle over a pit or on a hoist. | | | | | |

6.1.3. Fuel tank and pipes (including heating fuel tank and pipes)

Visual inspection with vehicle over a pit or on a hoist, use of leak detecting devices in the case of LPG/CNG/LNG systems. | General description and location including shielding | X | X | | X | X

6.1.4. Bumpers, lateral protection and rear underrun devices

Visual inspection. | Exempt side guards and or rear underrun (Y/N) | | X | X | |

6.1.5. Spare wheel carrier (if fitted)

Visual inspection. | | | | | |

6.1.6. Mechanical coupling and towing device

Visual inspection for wear and correct operation with special attention to any safety device fitted and/or use of measuring gauge. | | | | | |

6.1.7. Transmission

Visual inspection. | | | | | |

6.1.8. Engine mountings

Visual inspection not necessarily on a pit or hoist. | | | | | |

6.1.9. Engine performance (X)2

Visual inspection and/or using electronic interface | Engine Control Unit valid configuration | X | X | | X | X

Instructions for the use of the electronic vehicle interface | X | X | | X | X

Instructions on how to read the Calibration Identification | X | X | | X | X

Information about the valid Calibration Identifications | X | X | | X | X

Software identification number including checksums or similar integrity validation data. | X | X | | X | X

6.2. Cab and bodywork

6.2.1. Condition

Visual inspection | | | | | |

6.2.2. Mounting

Visual inspection over a pit or on a hoist. | | | | | |

6.2.3. Doors and door catches

Visual inspection. | | | | | |

6.2.4. Floor

Visual inspection over a pit or on a hoist. | | | | | |

6.2.5. Driver's seat

Visual inspection. | | | | | |

6.2.6. Other seats

Visual inspection. | Max Number of seats total (excluding driver's seat) | X | X | | |

Number of rear-facing seats | X | X | | |

6.2.7. Driving controls

Visual inspection and by operation. | | | | | |

6.2.8. Cab steps

Visual inspection. | | | | | |

6.2.9. Other interior and exterior fittings and equipment

Visual inspection. | | | | | |

6.2.10. Mudguards (wings), spray suppression devices

Visual inspection. | | | | | |

6.2.11. Stand

Visual inspection. | | | | | |

6.2.12. Handgrips and footrests

Visual inspection. | | | | | |

7.

OTHER EQUIPMENT

7.1. Safety-belts/buckles and restraint systems (as regards L category: L6/L7)

7.1.1. Security of safety-belts/buckles mounting

Visual inspection. | Number and location of safety belt anchorage points | X | X | | X | X

7.1.2. Condition of safety-belts/buckles.

Visual inspection and by operation. | Safety belt category for each sitting position | X | X | | X | X

7.1.3. Safety belt load limiter

Visual inspection, and/or using electronic interface | instructions for the use of the electronic vehicle interface | X | X | | X |

7.1.4. Safety belt Pre-tensioners

Visual inspection, and/or using electronic interface | instructions for the use of the electronic vehicle interface | X | X | | X |

7.1.5. Airbag

Visual inspection, and/or using electronic interface | Number of airbags and location | X | X | | X |

instructions for the use of the electronic vehicle interface | X | X | | X |

7.1.6. SRS Systems

Visual inspection of MIL, and/or using electronic interface | instructions for the use of the electronic vehicle interface | X | X | | X |

7.2. Fire extinguisher (X)2

Visual inspection. | | | | | |

7.3. Locks and anti-theft device

Visual inspection and by operation | | | | | |

7.4. Warning triangle (if required) (X)2

Visual inspection. | | | | | |

7.5. First aid kit. (if required) (X)2

Visual inspection. | | | | | |

7.6. Wheel chocks (wedges) (if required) (X)2

This article is long: the rest is at the official publication.