11 ANNEX Xa, Regulation (EU) 2017/2400

No longer in force

This Annex sets out the requirements for the verification testing procedure, which is the test procedure for verifying the CO2 emissions of new medium and heavy lorries.

The verification testing procedure consists of an on-road test to verify the CO2 emissions of new vehicles after production. It shall be carried out by the vehicle manufacturer and supervised by the approval authority that granted the licence to operate the simulation tool.

During the verification testing procedure the torque and speed at the driven wheels, the engine speed, the fuel consumption, the engaged gear of the vehicle and the other relevant parameters listed in point 6.1.6 shall be measured. The measured data shall be used as input to the simulation tool, which uses the vehicle-related input data and the input information from the determination of the CO2 emissions and fuel consumption of the vehicle. For the verification testing procedure simulation, the instantaneously measured wheel torque and the rotational speed of the wheels as well as the engine speed shall be used as input. To pass the verification testing procedure the CO2 emissions calculated from the measured fuel consumption shall be within the tolerances set out in point 7 compared to the CO2 emissions from the verification testing procedure simulation. Figure 1 gives a schematic picture of the verification testing procedure method. The evaluation steps as performed by the simulation tool in the verification testing procedure simulation are described in Appendix 1 of this Annex.

As part of the verification testing procedure, the correctness of the vehicle input data set from the certification of CO2 emissions and fuel consumption related properties of the components, separate technical units and systems shall also be reviewed to check the data and the data handling process. The correctness of the input data relating to components, separate technical units and systems relevant for air drag and for rolling resistance of the vehicle shall be verified in accordance with point 6.1.1.

For the purposes of this Annex the following definitions shall apply:

(1)

‘verification test relevant data set’ means a set of input data for components, separate technical units and systems and input information used for CO2 determination of a verification testing procedure relevant vehicle;

(2)

‘verification testing procedure relevant vehicle’ means a new vehicle for which a value of CO2 emissions and fuel consumption was determined and declared in accordance with Article 9;

(3)

‘corrected actual mass of the vehicle’ means the ‘corrected actual mass of the vehicle’ as defined in Annex III, point 2(4);

(4)

‘actual mass of the vehicle for VTP’ is the actual mass of the vehicle as defined in Article 2(6) of Regulation (EU) No 1230/2012, but with a full-tank and plus the additional measurement equipment as set out in point 5 (measurement equipment), plus the actual mass of the trailer or semitrailer if demanded by 6.1.4.1;

(5)

‘actual mass of the vehicle for VTP with payload’ means the actual mass of the vehicle for VTP with the payload applied in the verification testing procedure as set out in 6.1.4.2;

(6)

‘wheel power’ means the total power at the driven wheels of a vehicle to overcome all driving resistances at the wheel, computed in the simulation tool from the measured torque and rotational speed of the driven wheels;

(7)

‘controller area network signal’ or ‘CAN signal’ means a signal from the connection with the vehicle electronic control unit as referred to in point 2.1.5 of Appendix 1 to Annex II to Regulation (EU) No 582/2011;

(8)

‘urban driving’ means the total distance driven during the fuel consumption measurement at speeds not exceeding 50 km/h;

(9)

‘rural driving’ means the total distance driven during the fuel consumption measurement at speeds exceeding 50 km/h, but not exceeding 70 km/h;

(10)

‘motorway driving’ means the total distance driven in the fuel consumption measurement at speeds above 70 km/h;

(11)

‘crosstalk’ means the signal at the main output of a sensor (My), produced by a measurand (Fz) acting on the sensor, which is different from the measurand assigned to this output; the coordinate system assignment is defined in accordance with ISO 4130.

The number of new vehicles to be tested per year of production ensures that the relevant variations of components, separate technical units or systems used are covered by the verification testing procedure. The vehicle selection for the verification test shall be based on the following requirements:

(a)

The vehicles for the verification test shall be selected out of the vehicles from the production line for which a value of CO2 emissions and fuel consumption has been determined and declared in accordance with Article 9. The components, separate technical units or systems mounted in or on the vehicle shall be out of series production and shall correspond to those mounted at production date of the vehicle.

(b)

The vehicle selection shall be made by the approval authority that granted the licence to operate the simulation tool based on proposals from the vehicle manufacturer.

(c)

Only vehicles with one driven axle shall be selected for verification test.

(d)

It is recommended to include in each verification test relevant data sets of the components of interest and with the highest sales numbers per manufacturer. The components, separate technical units or systems may be verified all in one vehicle or in different vehicles. Apart from the criterion of highest sales numbers, the approval authority mentioned in (b) shall decide whether other vehicles with relevant data sets engine, axle and transmission shall be included in the verification test.

(e)

Vehicles which use standard values for CO2 certification of their components, separate technical units or systems instead of measured values for the transmission and for the axle losses shall not be selected for the verification test as long as vehicles complying with the requirements in points (a) to (c) and using measured loss maps for these components, separate technical units or systems in the CO2 certification, are produced.

(f)

The minimum number of different vehicles with different combinations of verification test relevant data sets to be tested by verification test per year shall be based on the sales numbers of the vehicle manufacturer as set out in Table 1.

[The total of all vehicles by a manufacturer falling within the scope of this regulation is to be considered and both medium lorries as well as heavy lorries need to be covered by the VTP over a six-year time span.] [The VTP shall be performed within the first two years.]

Number of vehicles to be tested | Schedule | Verification testing procedure relevant vehicles produced / year

0 | — | ≤ 25

1 | every 3 years | 26 – 250

1 | every 2 years | 251 – 5000

1 | every year | 5001 – 25000

2 | every year | 25001 – 50000

3 | every year | 50001 – 75000

4 | every year | 75001 – 100000

5 | every year | more than 100000

(g)

The vehicle manufacturer shall finalize the verification test within a period of 10 months after the date of selection of the vehicle for the verification test.

Each vehicle for the verification test shall be in the condition resembling its intended placing on the market. No changes in hardware such as lubricants or in the software such as auxiliary controllers are allowed. The tyres may be replaced by measurement tyres of similar size (± 10 %).

The provisions as set out in points 3.3 to 3.6 of Annex II to Regulation (EU) 582/2011 shall apply.

Run in of the vehicle is not mandatory. If the total mileage of the test vehicle is less than 15000 km, an evolution coefficient for the test result is applied by the simulation tool as defined in Appendix 1. The total mileage of the test vehicle shall be the odometer reading at start of the fuel consumption measurement. The maximum mileage at start of the warm-up shall be 20000 km.

All lubricants shall be the same as the lubricants used when placing the vehicle on the market.

For the fuel consumption measurement as described in point 6.1.5 the fuel used shall be the one available on the market. In any case of dispute the fuel shall be the appropriate reference fuel specified in Annex IX to Regulation (EU) No 582/2011.

The fuel tank shall be full at start of the vehicle warm up. Refuelling of the vehicle between start of warm up and end of fuel consumption measurement is not allowed.

The net calorific value (NCV) of the fuel used in the verification test shall be determined in accordance with point 3.2 of Annex V. The fuel batch shall be taken from the tank after vehicle warm-up. In the case of dual-fuel engines, this procedure shall be applied to both fuels.

The calibration laboratory facilities shall comply with the requirements of either IATF 16949, ISO 9000 series or ISO/IEC 17025. All laboratory reference measurement equipment, used for calibration and verification, shall be traceable to national or international standards.

The direct torque at all driven axles shall be measured with one of the following measurement systems fulfilling the requirements listed in Table 2:

(a)

hub torque meter;

(b)

rim torque meter;

(c)

half-shaft torque meter.

The drift shall be measured during the verification test by zeroing the torque measurement system in accordance with point 6.1.5.4 after the vehicle warm up in accordance with point 6.1.5.3. by lifting the axle and measuring the torque at lifted axle directly after the verification test again in accordance with point 6.1.5.6.

For a valid test result a maximum drift (sum of absolute values of both wheels) of the torque measurement system over the verification testing procedure of 1,5 % of the calibrated range of a single torque meter shall be proven.

The recorded vehicle speed shall be based on the CAN signal.

For vehicles with SMT and AMT transmissions the engaged gear is calculated by the simulation tool based on measured engine speed, the vehicle speed and the tyre dimensions and transmission ratios of the vehicle in accordance with Appendix 1. The engine speed is taken by the simulation tool from the input data as defined in point 5.4.

For vehicles with APT transmissions the engaged gear as well as the status of the torque converter (active or not active) shall be provided from CAN signals.

The rotational speed of the engine shall be recorded from the CAN, OBD or alternative measurement systems that fulfil the requirements set out in Table 2.

The rotational speed of the left and right wheel of the driven axle shall be recorded from the CAN or alternative measurement systems that fulfil the requirements set out in Table 2.

For non-electrically driven engine cooling fans the rotational speed of the fan shall be recorded. For this purpose either the CAN signal or alternatively an external sensor fulfilling the requirements set out in Table 2 shall be used.

For electrically driven engine cooling fans the current and voltage shall be recorded for the direct current input at the terminal of the electric motor or the inverter. From these two signals, the electrical power at the terminal shall be calculated by multiplication and shall be available as a time-resolved signal as input to the simulation tool. In the case of multiple electrically driven engine cooling fans, the sum of electrical power at the terminals shall be made available.

The fuel consumed shall be measured on-board with a measurement device based on one of the following measurement methods:

Measurement of fuel mass. The fuel measuring device shall fulfil the accuracy requirements set out in Table 2 for the fuel mass measurement system.

Measurement of fuel volume together with correction for the thermal expansion of the fuel. The fuel volume measurement device and fuel temperature measurement device shall fulfil the accuracy requirements set out in Table 2 for the fuel volume measurement system. Measured values of fuel volume flow shall be converted to fuel mass flow in accordance with the following equations:

mfuel,i = Vfuel,i·ρi

ρi

ρ0

1 βti 1 t0

where:

mfuel, iFuel mass flow at sample i [g/h]

ρ0Density of the fuel used for the verification test in (g/dm3). The density shall be determined in accordance with Annex IX to the Regulation (EU) No 582/2011. If diesel fuel is used in the verification test, also the average value of the density interval for the reference fuels B7 in accordance with Annex IX to the Regulation (EU) No 582/2011 may be used.

t0Fuel temperature that corresponds to density ρ0 for the reference fuel [°C]

ρiDensity of the test fuel at sample i [g/dm3]

Vfuel, iFuel volume flow at sample i [dm3/h]

tiMeasured fuel temperature at sample i [°C]

βTemperature correction factor (0,001 K–1).

For dual-fuel vehicles the fuel flow shall be measured for each of the two fuels separately.

The following masses of the vehicle shall be measured with equipment fulfilling the requirements set out in Table 2:

(a)

actual mass of the vehicle for VTP;

(b)

actual mass of the vehicle for VTP with payload.

The input data as set out in point 6.1.6. Table 4 shall be provided from the measurements. All data shall be recorded at least in 2 Hz frequency or at recommended frequency from the equipment maker, whichever is the higher value.

The input data for the simulation tool may be composed from different recorders. The torque and rotational speed at the wheels shall be recorded in one data-logging system. If different data-logging systems are used for the other signals, one common signal, such as vehicle speed, shall be recorded to ensure correct time alignment of the signals. The time alignment of the signals shall result in the highest correlation coefficient of the common signal recorded with the different data loggers.

The accuracy requirements set out in Table 2 shall be met by all measurement equipment used. Any equipment not listed in Table 2 shall fulfil the accuracy requirements set out in Table 2 of Annex V.

[Rise time means the difference in time between the 10 % and 90 % response of the final analyser reading (t90 – t10).] [The accuracy shall be met for the integral fuel flow over 100 minutes.] [Non linearity means the maximum deviation between ideal and actual output signal characteristics in relation to the measured value in a specific measuring range.] [Repeatability means closeness of the agreement between the results of successive measurements of the same measured value carried out under the same conditions of measurement.]

Measurement system | Accuracy | Rise time

Balance for vehicle weight |

50 kg or

< 0,5 % of max. calibration whichever is smaller

—

Rotational speed wheels | < 0,5 % of reading at 80 km/h | ≤ 1 s

Fuel mass flow for liquid fuels |

< 1,0 % of reading or

< 0,2 % of max. calibration whichever is larger

—

Fuel mass flow for gaseous fuels |

< 1,0 % of reading or

< 0,5 % of max. calibration whichever is larger

—

Fuel volume measurement system |

< 1,0 % of reading or

< 0,5 % of max. calibration whichever is larger

—

Temperature of the fuel | ± 1 °C | ≤ 2 s

Sensor for measuring the rotational speed cooling fan |

< 0,4 % of reading or

< 0,2 % of max. calibration of speed whichever is larger

≤ 1 s

Voltage |

< 2 % of reading or

< 1 % of max. calibration of speed whichever is larger

≤ 1 s

Current |

< 2 % of reading or

< 1 % of max. calibration of speed whichever is larger

≤ 1 s

Engine speed |

As set out in Annex V.

In the case of vehicles with engine stop-start, it shall be verified that the engine speed is also recorded correctly for speeds below idle.

Wheel torque |

For 10 kNm calibration (over the entire calibration range):

i.

Non linearity:

< ± 40 Nm for heavy lorries

< ± 30 Nm for medium lorries

ii.

Repeatability:

< ± 20 Nm for heavy lorries

< ± 15 Nm for medium lorries

iii. Crosstalk:

< ± 20 Nm for heavy lorries

< ± 15 Nm for medium lorries

(only applicable for rim torque meters)

iv. Measurement rate: ≥ 20 Hz

< 0,1 s

The maximum calibration values shall be the maximum expected values during all test runs for the respective measurement system, multiplied by an arbitrary factor larger than 1 and less or equal than 2. For the torque measurement system the maximum calibration may be limited to 10 kNm.

In the case of dual-fuel engines, the maximum calibration value for the measurement system for fuel mass flow or fuel volume shall be determined following the requirements laid down in point 3.5 of Annex V. For fuel volume the maximum calibration value shall be determined by dividing the maximum calibration values for fuel mass flow by the density value ρ0 defined in accordance with point 5.7.

Accuracy given shall be met by the sum of all single accuracies in the case more than one scale is used.

The engine torque shall be recorded during the verification testing procedure for the purpose of evaluating pollutant emissions. The signal shall fulfil the provisions as specified for the engine torque signal in Table 1 of point 2.2 of Appendix 1 to Annex II to Regulation (EU) 582/2011.

For measurement of pollutant emissions the instrumentation and procedures as set out in Appendices 1 to 4 of Annex II to Regulation (EU) 582/2011 shall be used. The data evaluation shall provide instantaneous emission mass flows as set out in Table 4 of point 6.1.6. as input to the simulation tool.

Based on these input signals the simulation tool automatically calculates the brake specific pollutant emissions measured in the verification test (BSEM) as set out in Part B of Appendix 1 of this Annex. These results are then automatically written into the output of the simulation tool according to point 8.13.14. The additional requirements set out in Regulation (EU) 582/2011 on data evaluation (e.g. work based windows, moving average windows), test start and trip shall not apply.

In the verification test procedure, pass/fail criteria regarding pollutant emissions shall not apply.

The vehicle shall be taken from the series production and selected as set out in point 3.

The manufacturer's records file and the customer information file for the vehicle selected shall be used as basis for verifying the input data. The vehicle identification number of the vehicle selected shall be the same as the vehicle identification number in the manufacturer's records file and the customer information file.

Upon request by the approval authority that granted the licence to operate the simulation tool, the vehicle manufacturer shall provide, within 15 working days, the manufacturer's records file, the input information and input data necessary to run the simulation tool as well as the certificate of CO2 emissions and fuel consumption related properties for all relevant components, separate technical units or systems.

The following checks shall be performed for the components, separate technical units and systems mounted on the vehicle:

(a)

Simulation tool data integrity: the integrity of the cryptographic hash of the manufacturer’s records file in accordance with Article 9(3) re-calculated during the verification testing procedure with the hashing tool shall be verified by comparison with the cryptographic hash in the certificate of conformity;

(b)

Vehicle data: the vehicle identification number, axle configuration, selected auxiliaries and power take off technology, disabled gears in accordance with point 6.2 of Annex III and requirements on active aero devices as set out in point 3.3.1.5 of Annex VIII shall match the selected vehicle;

(c)

Engine torque limitations declared in the input to the simulation tool are subject to a verification in the VTP if they are declared for any of the highest 50 % of the gears (e.g. for any of the gears 7 to 12 of a 12-gear transmission) and if one of the following cases shall apply:

(i)

Torque limit declared on the vehicle level in accordance with point 6.1 of Annex III

(ii)

Torque limit declared in the input to the transmission component in accordance with parameter P157 in Table 2 of Appendix 12 of Annex VI and if the declared value does not exceed 90 % of the engine maximum torque

For any of the torque limits subject to a verification it shall be demonstrated that the 99 % percentile of the engine torque recorded during the fuel consumption measurement in the relevant gear does not exceed the declared torque limit by more than 5 %. For this purpose the verification test shall cover phases of full throttle in the respective gears. The verification shall be performed based on recorded engine torque as set out in 5.10.

The engine torque limitation verification may also be performed as a separate test only, consisting of dedicated full-load accelerations and with no other obligations on test evaluation.

(d)

Component, separate technical unit or system data: the certification number and the model type imprinted on the certificate of CO2 emissions and fuel consumption related properties shall match the component, separate technical unit or system installed in the selected vehicle;

(e)

The hash of the simulation tool input data and the input information shall match the hash imprinted on the certificate of CO2 emissions and fuel consumption related properties for the following components, separate technical units or systems:

(i)

engines;

(ii)

transmissions;

(iii)

torque converters;

(iv)

other torque transferring components;

(v)

additional drivetrain components;

(vi)

axles;

(vii)

body or trailer air drag;

(viii)

tyres.

If requested by the approval authority that granted the licence to operate the simulation tool, the determination of masses by the manufacturer shall be verified in accordance with point 2 of Appendix 2 of Annex I to Regulation (EU) No 1230/2012. Where that verification fails, the corrected actual mass as defined in point 2(4) of Annex III to this Regulation shall be determined.

In the case of discrepancies in the certification number or the cryptographic hash of one or more files regarding the components, separate technical units or systems listed in subpoints (1) to (8) of point 6.1.1.1 (e) the correct input data file fulfilling the checks in accordance with points 6.1.1.1 and 6.1.1.2 shall replace the incorrect data for all further actions. The same applies to any other incorrect information identified in subpoints (b) and (c) of point 6.1.1.1.

This article is long: the rest is at the official publication.