72 Sub-Annex 7, Regulation (EU) 2017/1151

No longer in force

1.1.

Calculations related specifically to hybrid, pure electric and compressed hydrogen fuel cell vehicles are described in Sub-Annex 8.

A stepwise procedure for calculating test results is described in paragraph 4. of Sub-Annex 8.

1.2.

The calculations described in this Sub-Annex shall be used for vehicles using combustion engines.

1.3.1. Intermediate steps in the calculations shall not be rounded.

1.3.2. The final criteria emission results shall be rounded in one step to the number of places to the right of the decimal point indicated by the applicable emission standard plus one additional significant figure.

1.3.3. The NOx correction factor, KH, shall be rounded to two decimal places.

1.3.4. The dilution factor, DF, shall be rounded to two decimal places.

1.3.5. For information not related to standards, good engineering judgement shall be used.

1.3.6. Rounding of CO2 and fuel consumption results is described in paragraph 1.4. of this Sub-Annex.

The results shall be calculated in the order described in Table A7/1. All applicable results in the column ‘Output’ shall be recorded. The column ‘Process’ describes the paragraphs to be used for calculation or contains additional calculations.

For the purpose of this table, the following nomenclature within the equations and results is used:

ccomplete applicable cycle;

pevery applicable cycle phase;

ievery applicable criteria emission component, without CO2;

CO2CO2 emission.

Source | Input | Process | Output | Step No.

Sub-Annex 6 | Raw test results |

Mass emissions

Paragraphs 3. to 3.2.2. of this Sub-Annex.

Mi,p,1, g/km;

MCO2,p,1, g/km.

1

Output step 1 |

Mi,p,1, g/km;

MCO2,p,1, g/km.

Calculation of combined cycle values:

Mi,c,2

pMi,p,1dp

pdpMCO2,c,2

pMCO2,p,1dp

pdp

where:

Mi/CO2,c,2 are the emission results over the total cycle;

dp are the driven distances of the cycle phases, p.

Mi,c,2, g/km;

MCO2,c,2, g/km.

2

Output step 1 and 2 |

MCO2,p,1, g/km;

MCO2,c,2, g/km.

Correction of CO2 results against the target speed and distance.

Sub-Annex 6b.

Note: As the distance is also corrected, from this calculation step onwards any reference to a driven distance shall be interpreted as a reference to the target distance.

MCO2,p,2b, g/km;

MCO2,c,2b, g/km.

2b

Output step 2b |

MCO2,p,2b, g/km;

MCO2,c,2b, g/km.

RCB correction

Appendix 2 to Sub-Annex 6.

MCO2,p,3, g/km;

MCO2,c,3, g/km.

3

Output step 2 and 3 |

Mi,c,2, g/km;

MCO2,c,3, g/km.

Emissions test procedure for all vehicles equipped with periodically regenerating systems, Ki.

Sub-Annex 6, Appendix 1.

Mi,c,4 = Ki × Mi,c,2

or

Mi,c,4 = Ki + Mi,c,2

and

MCO2,c,4 = KCO2 × MCO2,c,3

or

MCO2,c,4 = KCO2 + MCO2,c,3

Additive offset or multiplicative factor to be used in accordance with Ki determination.

If Ki is not applicable:

Mi,c,4 = Mi,c,2

MCO2,c,4 = MCO2,c,3

Mi,c,4, g/km;

MCO2,c,4, g/km.

4a

Output step 3 and 4a |

MCO2,p,3, g/km;

MCO2,c,3, g/km;

MCO2,c,4, g/km.

If Ki is applicable, align CO2 phase values to the combined cycle value:

MCO2,p,4 = MCO2,p,3 × AFKi

for every cycle phase p;

where:

AFKiMCO2,c,4MCO2,c,3

If Ki is not applicable:

MCO2,p,4 = MCO2,p,3

MCO2,p,4, g/km. | 4b

Output step 4 |

Mi,c,4, g/km;

MCO2,c,4, g/km;

MCO2,p,4, g/km.

ATCT correction in accordance with paragraph 3.8.2. of Sub-Annex 6a.

Deterioration factors calculated in accordance with Annex VII and applied to the criteria emissions values.

Mi,c,5, g/km;

MCO2,c,5, g/km;

MCO2,p,5, g/km.

5

Result of a single test.

Output step 5 |

For every test:

Mi,c,5, g/km;

MCO2,c,5, g/km;

MCO2,p,5, g/km.

Averaging of tests and declared value.

Paragraphs 1.2. to 1.2.3. of Sub-Annex 6.

Mi,c,6, g/km;

MCO2,c,6, g/km;

MCO2,p,6, g/km.

MCO2,c,declared, g/km.

6

Output step 6 |

MCO2,c,6, g/km;

MCO2,p,6, g/km.

MCO2,c,declared, g/km.

Alignment of phase values.

Paragraph 1.2.4. of Sub-Annex 6.

and:

MCO2,c,7 = MCO2,c,declared

MCO2,c,7, g/km;

MCO2,p,7, g/km.

7

Output steps 6 and 7 |

Mi,c,6, g/km;

MCO2,c,7, g/km;

MCO2,p,7, g/km.

Calculation of fuel consumption.

Paragraph 6 of this Sub-Annex.

The calculation of fuel consumption shall be performed for the applicable cycle and its phases separately. For that purpose:

(a)

the applicable phase or cycle CO2 values shall be used;

(b)

the criteria emission over the complete cycle shall be used.

and:

Mi,c,8 = Mi,c,6

MCO2,c,8 = MCO2,c,7

MCO2,p,8 = MCO2,p,7

FCc,8, l/100 km;

FCp,8, l/100 km;

Mi,c,8, g/km;

MCO2,c,8, g/km;

MCO2,p,8, g/km.

8

Result of a Type 1 test for a test vehicle.

Step 8 |

For each of the test vehicles H and L:

Mi,c,8, g/km;

MCO2,c,8, g/km;

MCO2,p,8, g/km;

FCc,8, l/100 km;

FCp,8, l/100 km.

If a test vehicle L was tested in addition to a test vehicle H, the resulting criteria emission value shall be the highest of the two values and referred to as Mi,c.

In the case of the combined THC + NOx emissions, the highest value of the sum referring to either the VH or VL is to be used.

Otherwise, if no vehicle L was tested, Mi,c = Mi,c,8

For CO2 and FC, the values derived in step 8 shall be used, and CO2 values shall be rounded to two decimal places, and FC values shall be rounded to three decimal places.

Mi,c, g/km;

MCO2,c,H, g/km;

MCO2,p,H, g/km;

FCc,H, l/100 km;

FCp,H, l/100 km;

and if a vehicle L was tested:

MCO2,c,L, g/km;

MCO2,p,L, g/km;

FCc,L, l/100 km;

FCp,L, l/100 km.

9

Interpolation family result.

Final criteria emission result.

Step 9 |

MCO2,c,H, g/km;

MCO2,p,H, g/km;

FCc,H, l/100 km;

FCp,H, l/100 km;

and if a vehicle L was tested:

MCO2,c,L, g/km;

MCO2,p,L, g/km;

FCc,L, l/100 km;

FCp,L, l/100 km.

Fuel consumption and CO2 calculations for individual vehicles in an interpolation family.

Paragraph 3.2.3. of this Sub-Annex.

CO2 emissions shall be expressed in grams per kilometre (g/km) rounded to the nearest whole number;

FC values shall be rounded to one decimal place, expressed in (l/100 km).

MCO2,c,ind g/km;

MCO2,p,ind, g/km;

FCc,ind l/100 km;

FCp,ind, l/100 km.

10

Result of an individual vehicle.

Final CO2 and FC result.

The volumetric flow shall be measured continuously. The total volume shall be measured for the duration of the test.

2.1.1. The volumetric flow shall be measured continuously. The total volume shall be measured for the duration of the test.

2.2.1.

The volume shall be calculated using the following equation:

VV0 N

where:

Vis the volume of the diluted gas, in litres per test (prior to correction);

V0is the volume of gas delivered by the positive displacement pump in testing conditions, litres per pump revolution;

Nis the number of revolutions per test.

The diluted exhaust gas volume, V, shall be corrected to standard conditions according to the following equation:

VmixV K1 PB P1Tp

where:

K1273,15K101,325kPa 2,6961

PBis the test room barometric pressure, kPa;

P1is the vacuum at the inlet of the positive displacement pump relative to the ambient barometric pressure, kPa;

Tpis the arithmetic average temperature of the diluted exhaust gas entering the positive displacement pump during the test, Kelvin (K).

3.1.1. Assuming no compressibility effects, all gases involved in the engine's intake, combustion and exhaust processes may be considered to be ideal according to Avogadro’s hypothesis.

3.1.2. The mass, M of gaseous compounds emitted by the vehicle during the test shall be determined by the product of the volumetric concentration of the gas in question and the volume of the diluted exhaust gas with due regard for the following densities under the reference conditions of 273,15 K (0 °C) and 101,325 kPa:

Carbon monoxide (CO)ρ1,25g/l

Carbon dioxide (CO2)ρ1,964g/l

Hydrocarbons:

for petrol (E10) (C1H1,93 O0,033)ρ0,646g/l

for diesel (B7) (C1H1,86O0,007)ρ0,625g/l

for LPG (C1H2,525)ρ0,649g/l

for NG/biomethane (CH4)ρ0,716g/l

for ethanol (E85) (C1H2,74O0,385)ρ0,934g/l

Nitrogen oxides (NOx)ρ2,05g/l

The density for NMHC mass calculations shall be equal to that of total hydrocarbons at 273,15 K (0 °C) and 101,325 kPa, and is fuel-dependent. The density for propane mass calculations (see paragraph 3.5. in Sub-Annex 5) is 1,967 g/l at standard conditions.

If a fuel type is not listed in this paragraph, the density of that fuel shall be calculated using the equation given in paragraph 3.1.3. of this Sub-Annex.

3.1.3. The general equation for the calculation of total hydrocarbon density for each reference fuel with an mean composition of CXHYOZ is as follows:

ρTHCMWCHC MWHOC MWOVM

where:

ρTHCis the density of total hydrocarbons and non-methane hydrocarbons, g/l;

MWCis the molar mass of carbon (12,011 g/mol);

MWHis the molar mass of hydrogen (1,008 g/mol);

MWOis the molar mass of oxygen (15,999 g/mol);

VMis the molar volume of an ideal gas at 273,15 K (0°C) and 101,325 kPa (22,413 l/mol);

H/Cis the hydrogen to carbon ratio for a specific fuel CXHYOZ;

O/Cis the oxygen to carbon ratio for a specific fuel CXHYOZ.

3.2.1.

Mass emissions of gaseous compounds per cycle phase shall be calculated using the following equations:

Mi,phaseVmix,phase ρi KHphase Ci,phase 10 6dphase

where:

Miis the mass emission of compound i per test or phase, g/km;

Vmixis the volume of the diluted exhaust gas per test or phase expressed in litres per test/phase and corrected to standard conditions (273,15 K (0 °C) and 101,325 kPa);

ρiis the density of compound i in grams per litre at standard temperature and pressure (273,15 K (0 °C) and 101,325 kPa);

KHis a humidity correction factor applicable only to the mass emissions of oxides of nitrogen, NO2 and NOx, per test or phase;

Ciis the concentration of compound i per test or phase in the diluted exhaust gas expressed in ppm and corrected by the amount of compound i contained in the dilution air;

dis the distance driven over the applicable WLTC, km;

nis the number of phases of the applicable WLTC.

3.2.1.1.

The concentration of a gaseous compound in the diluted exhaust gas shall be corrected by the amount of the gaseous compound in the dilution air using the following equation:

CiCe Cd 1 1DF

where:

Ciis the concentration of gaseous compound i in the diluted exhaust gas corrected by the amount of gaseous compound i contained in the dilution air, ppm;

Ceis the measured concentration of gaseous compound i in the diluted exhaust gas, ppm;

Cdis the concentration of gaseous compound i in the dilution air, ppm;

DFis the dilution factor.

3.2.1.1.1.

The dilution factor DF shall be calculated using the equation for the concerned fuel:

DF13.4CCO2 CHC CCO 10 4for petrol (E10)

DF13.5CCO2 CHC CCO 10 4for diesel (B7)

DF11.9CCO2 CHC CCO 10 4for LPG

DF9.5CCO2 CHC CCO 10 4for NG/biomethane

DF12.5CCO2 CHC CCO 10 4for ethanol (E85)

DF35.03CH2O CH2O DA CH2 10 4for hydrogen

With respect to the equation for hydrogen:

CH2Ois the concentration of H2O in the diluted exhaust gas contained in the sample bag, per cent volume;

CH2O-DAis the concentration of H2O in the dilution air, per cent volume;

CH2is the concentration of H2 in the diluted exhaust gas contained in the sample bag, ppm.

If a fuel type is not listed in this paragraph, the DF for that fuel shall be calculated using the equations in paragraph 3.2.1.1.2. of this Sub-Annex.

If the manufacturer uses a DF that covers several phases, it shall calculate a DF using the mean concentration of gaseous compounds for the phases concerned.

The mean concentration of a gaseous compound shall be calculated using the following equation:

C i

nphase 1 Ci,phase Vmix,phase

nphase 1 Vmix,phase

where:

Ciis mean concentration of a gaseous compound;

Ci,phaseis the concentration of each phase;

Vmix,phaseis the Vmix of the corresponding phase;

3.2.1.1.2.

The general equation for calculating the dilution factor DF for each reference fuel with an arithmetic average composition of CxHyOz is as follows:

DFXCCO2 CHC CCO 10 4

where:

X100 xx y2 3,76x y4 z2

CCO2is the concentration of CO2 in the diluted exhaust gas contained in the sample bag, per cent volume;

CHCis the concentration of HC in the diluted exhaust gas contained in the sample bag, ppm carbon equivalent;

CCOis the concentration of CO in the diluted exhaust gas contained in the sample bag, ppm.

3.2.1.1.3.1.

For methane measurement using a GC-FID, NMHC shall be calculated using the following equation:

CNMHCCTHC RfCH4 CCH4

where:

CNMHCis the corrected concentration of NMHC in the diluted exhaust gas, ppm carbon equivalent;

CTHCis the concentration of THC in the diluted exhaust gas, ppm carbon equivalent and corrected by the amount of THC contained in the dilution air;

CCH4is the concentration of CCH4 in the diluted exhaust gas, ppm carbon equivalent and corrected by the amount of CH4 contained in the dilution air;

RfCH4is the FID response factor to methane determined and specified in paragraph 5.4.3.2. of Sub-Annex 5.

3.2.1.1.3.2.

For methane measurement using an NMC-FID, the calculation of NMHC depends on the calibration gas/method used for the zero/calibration adjustment.

The FID used for the THC measurement (without NMC) shall be calibrated with propane/air in the normal manner.

For the calibration of the FID in series with an NMC, the following methods are permitted:

(a)

The calibration gas consisting of propane/air bypasses the NMC;

(b)

The calibration gas consisting of methane/air passes through the NMC.

It is highly recommended to calibrate the methane FID with methane/air through the NMC.

In case (a), the concentration of CH4 and NMHC shall be calculated using the following equations:

CCH4CHCwNMC CHCwoNMC 1EERfCH4 EE EMCNMHCCHCwoNMC 1EM CHCwNMCEE EM

If RfCH4 < 1,05, it may be omitted from the equation above for CCH4.

In case (b), the concentration of CH4 and NMHC shall be calculated using the following equations:

CCH4CHCwNMC RfCH4 1EM CHCwoNMC 1EERfCH4 EE EMCNMHCCHCwoNMC 1EM CHCwNMC RfCH4 1EMEE EM

where:

CHC(w/NMC)is the HC concentration with sample gas flowing through the NMC, ppm C;

CHC(w/oNMC)is the HC concentration with sample gas bypassing the NMC, ppm C;

RfCH4is the methane response factor as determined per paragraph 5.4.3.2. of Sub-Annex 5;

EMis the methane efficiency as determined per paragraph 3.2.1.1.3.3.1. of this Sub-Annex;

EEis the ethane efficiency as determined per paragraph 3.2.1.1.3.3.2. of this Sub-Annex.

If RfCH4 < 1,05, it may be omitted in the equations for case (b) above for CCH4 and CNMHC.

The NMC is used for the removal of the non-methane hydrocarbons from the sample gas by oxidizing all hydrocarbons except methane. Ideally, the conversion for methane is 0 per cent, and for the other hydrocarbons represented by ethane is 100 per cent. For the accurate measurement of NMHC, the two efficiencies shall be determined and used for the calculation of the NMHC emission.

The methane/air calibration gas shall be flowed to the FID through the NMC and bypassing the NMC and the two concentrations recorded. The efficiency shall be determined using the following equation:

EM1 CHC(w/NMC)CHC(w/oNMC)

where:

CHC(w/NMC)is the HC concentration with CH4 flowing through the NMC, ppm C;

CHC(w/oNMC)is the HC concentration with CH4 bypassing the NMC, ppm C.

The ethane/air calibration gas shall be flowed to the FID through the NMC and bypassing the NMC and the two concentrations recorded. The efficiency shall be determined using the following equation:

EE1 CHC(w/NMC)CHC(w/oNMC)

where:

CHC(w/NMC)is the HC concentration with C2H6 flowing through the NMC, ppm C;

CHC(w/oNMC)is the HC concentration with C2H6 bypassing the NMC, ppm C.

If the ethane conversion efficiency of the NMC is 0,98 or above, EE shall be set to 1 for any subsequent calculation.

3.2.1.1.3.4.

If the methane FID is calibrated through the cutter, EM shall be 0.

The equation to calculate CCH4 in paragraph 3.2.1.1.3.2. (case (b)) in this Sub-Annex becomes:

CCH4CHC(w/NMC)

The equation to calculate CNMHC in paragraph 3.2.1.1.3.2. (case (b)) in this Sub-Annex becomes:

CNMHCCHC(w/oNMC) CHC(w/NMC) rh

The density used for NMHC mass calculations shall be equal to that of total hydrocarbons at 273,15 K (0 °C) and 101,325 kPa and is fuel-dependent.

The following calculation method shall only be applied for CVS systems that are not equipped with a heat exchanger or for CVS systems with a heat exchanger that do not comply with paragraph 3.3.5.1. of Sub-Annex 5.

When the CVS flow rate, qvcvs, over the test varies by more than ± 3 per cent of the arithmetic average flow rate, a flow-weighted arithmetic average shall be used for all continuous diluted measurements including PN:

Ce

ni 1 qvcvs(i) Δt C(i)V

where:

Ceis the flow-weighted arithmetic average concentration;

qvcvs(i)is the CVS flow rate at time t i Δt, m3/min;

C(i)is the concentration at time t i Δt, ppm;

Δtsampling interval, s;

Vtotal CVS volume, m3.

In order to correct the influence of humidity on the results of oxides of nitrogen, the following calculations apply:

KH11 0,0329 H 10,71

where:

H6,211 Ra PdPB Pd Ra 10 2

and:

His the specific humidity, grams of water vapour per kilogram dry air;

Rais the relative humidity of the ambient air, per cent;

Pdis the saturation vapour pressure at ambient temperature, kPa;

PBis the atmospheric pressure in the room, kPa.

The KH factor shall be calculated for each phase of the test cycle.

The ambient temperature and relative humidity shall be defined as the arithmetic average of the continuously measured values during each phase.

3.2.2.1. To calculate HC mass emission for compression-ignition engines, the arithmetic average HC concentration shall be calculated using the following equation:

Ce

t2t1

CHCdtt2 t1

where:

t2t1

CHCdtis the integral of the recording of the heated FID over the test (t1 to t2);

Ceis the concentration of HC measured in the diluted exhaust in ppm of Ci and is substituted for CHC in all relevant equations.

3.2.2.1.1. Dilution air concentration of HC shall be determined from the dilution air bags. Correction shall be carried out according to paragraph 3.2.1.1. of this Sub-Annex.

The CO2 value, as calculated in paragraphs 3.2.1. to 3.2.1.1.2. of this Sub-Annex, and fuel consumption, as calculated in accordance with paragraph 6. of this Sub-Annex, shall be attributed to all individual vehicles in the interpolation family and the interpolation method shall not be applicable.

The CO2 emissions and the fuel consumption for each individual vehicle in the interpolation family may be calculated according to the interpolation method outlined in paragraphs 3.2.3.2.1. to 3.2.3.2.5. inclusive of this Sub-Annex.

The mass of CO2 emissions, MCO2 L, and MCO2 H and its phases p, MCO2 L,p and MCO2 H,p, of test vehicles L and H, used for the following calculations, shall be taken from step 9 of Table A7/1.

Fuel consumption values are also taken from step 9 of Table A7/1 and are referred to as FCL,p and FCH,p.

In the case that the interpolation family is derived from one or more road load families, the calculation of the individual road load shall only be performed within the road load family applicable to that individual vehicle.

The test masses of vehicles H and L shall be used as input for the interpolation method.

TMind, in kg, shall be the individual test mass of the vehicle according to paragraph 3.2.25. of this Annex.

If the same test mass is used for test vehicles L and H, the value of TMind shall be set to the mass of test vehicle H for the interpolation method.

3.2.3.2.2.2.1.

The actual RRC values for the selected tyres on test vehicle L, RRL, and test vehicle H, RRH, shall be used as input for the interpolation method. See paragraph 4.2.2.1. of Sub-Annex 4.

If the tyres on the front and rear axles of vehicle L or H have different RRC values, the weighted mean of the rolling resistances shall be calculated using the equation in paragraph 3.2.3.2.2.2.3. of this Sub-Annex.

3.2.3.2.2.2.2.

For the tyres fitted to an individual vehicle, the value of the rolling resistance coefficient RRind shall be set to the RRC value of the applicable tyre energy efficiency class in accordance with Table A4/2 of Sub-Annex 4.

In the case where individual vehicles may be supplied with a complete set of standard wheels and tyres and a complete set of snow tyres (marked with 3 Peaked Mountain and Snowflake – 3PMS) with or without wheels, the additional wheels/tyres shall not be considered as optional equipment.

If the tyres on the front and rear axles belong to different energy efficiency classes, the weighted mean shall be used and calculated using the equation in paragraph 3.2.3.2.2.2.3. of this Sub-Annex.

If the same tyres, or tyres with the same rolling resistance coefficient were fitted to test vehicles L and H, the value of RRind for the interpolation method shall be set to RRH.

3.2.3.2.2.2.3.

Calculating the weighted mean of the rolling resistances

RRx = (RRx,FA × mpx,FA) + (RRx,RA × (1 – mpx,FA))

where:

xrepresents vehicle L, H or an individual vehicle.

RRL,FA and RRH,FAare the actual RRCs of the front axle tyres on vehicles L and H respectively, kg/tonne;

RRind,FAis the RRC value of the applicable tyre energy efficiency class in accordance with Table A4/2 of Sub-Annex 4 of the front axle tyres on the individual vehicle, kg/tonne;

RRL,RA, and RRH,RAare the actual RRCs of the rear axle tyres on vehicles L and H respectively, kg/tonne;

RRind,RAis the RRC value of the applicable tyre energy efficiency class in accordance with Table A4/2 of Sub-Annex 4 of the rear axle tyres on the individual vehicle, kg/tonne;

mpx,FAis the proportion of the vehicle mass in running order on the front axle;

RRx shall not be rounded or categorised to tyre energy efficiency classes.

3.2.3.2.2.3.

Aerodynamic drag of an individual vehicle

The aerodynamic drag shall be measured for each of the aerodynamic drag-influencing items of optional equipment and body shapes in a wind tunnel fulfilling the requirements of paragraph 3.2. of Sub-Annex 4 verified by the approval authority.

At the request of the manufacturer and with approval of the approval authority, an alternative method (e.g. simulation, wind tunnel not fulfilling the criteria in Sub-Annex 4) may be used to determine Δ(CD × Af) if the following criteria are fulfilled:

(a)

The alternative method shall fulfil an accuracy for Δ(CD × Af) of ± 0,015 m2 and, additionally, in the case that simulation is used, the Computational Fluid Dynamics method should be validated in detail such that the actual air flow patterns around the body, including magnitudes of flow velocities, forces, or pressures, are shown to match the validation test results;

(b)

The alternative method shall be used only for those aerodynamic-influencing parts (e.g. wheels, body shapes, cooling system) for which equivalency was demonstrated;

This article is long: the rest is at the official publication.

  1. 1 Jan 2019 – 1 Sep 2023earlier wording
  2. 1 Jun 2017 – 1 Jan 2019earlier wording