70 Sub-Annex 6a, Regulation (EU) 2017/1151

No longer in force

This Sub-Annex describes the supplemental Ambient Temperature Correction Test (ATCT) procedure to determine the CO2 emissions under representative regional temperature conditions.

1.1.

The CO2 emissions of ICE vehicles, NOVC-HEVs and the charge sustaining value of OVC-HEVs shall be corrected in accordance with the requirements of this Sub-Annex. No correction is required for the CO2 value of the charge depleting test. No correction is required for an Electric Range.

2.1.

Only vehicles which are identical with respect to all the following characteristics are permitted to be part of the same ATCT Family:

(a)

Powertrain architecture (i.e. internal combustion, hybrid, fuel cell, or electric);

(b)

Combustion process (i.e. two stroke or four stroke);

(c)

Number and arrangement of cylinders;

(d)

Method of engine combustion (i.e. indirect or direct injection);

(e)

Type of cooling system (i.e. air, water, or oil);

(f)

Method of aspiration (i.e. naturally aspirated, or charged);

(g)

Fuel for which the engine is designed (i.e. petrol, diesel, NG, LPG, etc.);

(h)

Catalytic converter (i.e. three-way catalyst, lean NOx trap, SCR, lean NOx catalyst or other(s));

(i)

Whether or not a particulate trap is installed; and

(j)

Exhaust gas recirculation (with or without, cooled or non-cooled).

In addition the vehicles shall be similar with respect to the following characteristics:

(k)

The vehicles shall have a variation in engine cylinder capacity of no more than 30 % of the vehicle with the lowest capacity; and

(l)

Engine compartment insulation shall be of a similar type regarding material, amount and location of the insulation. Manufacturers shall provide evidence (e.g. by CAD drawings) to the approval authority that for all vehicles in the family, the volume and weight of the insulation material which will be installed is greater than 90 % of that of the ATCT measured reference vehicle.

Difference in insulation material and location may also be accepted to be part of a single ATCT family under the condition that the test vehicle can be demonstrated as being the worst case with regards to engine compartment insulation.

2.1.1.

If active heat storage devices are installed, only vehicles that meet the following requirements shall be considered to be part of the same ATCT Family:

(i)

the heat capacity, defined by the enthalpy stored in the system, is within a range of 0 to 10 % above the enthalpy of the test vehicle; and

(ii)

the OEM can provide evidence to the technical service that the time for heat release at engine start within a family is within a range of 0 to 10 % below the time for the heat release of the test vehicle.

2.1.2.

Only vehicles that meet the criteria set out in paragraph 3.9.4. of this Sub-Annex 6a shall be considered to be part of the same ATCT Family.

The Type 1 test specified in Sub-Annex 6 shall be carried out with the exception of the requirements specified in paragraphs 3.1. to 3.9. of this Sub-Annex 6a. That requires also a new calculation and application of gearshift points in accordance with Sub-Annex 2 taking into account the different road load as specified in paragraph 3.4. of this Sub-Annex 6a.

3.1.1.

The temperature (Treg) at which the vehicle should be soaked and tested for the ATCT shall be 14 °C.

3.1.2.

The minimum soaking time (tsoak_ATCT) for the ATCT shall be 9 hours.

3.2.1.1.

The test cell shall have a temperature set point equal to Treg. The actual temperature value shall be within ± 3 °C at the start of the test and within ± 5 °C during the test.

3.2.1.2.

The specific humidity (H) of either the air in the test cell or the intake air of the engine shall be such that:

3,0 ≤ H ≤ 8,1 | (g H2O/kg dry air)

3.2.1.3.

The air temperature and humidity shall be measured at the cooling fan outlet at a rate of 0,1 Hz.

3.2.2.1.

The soak area shall have a temperature set point equal to Treg and the actual temperature value shall be within ± 3 °C on a 5 minute running arithmetic average and shall not show a systematic deviation from the set point. The temperature shall be measured continuously at a minimum frequency of 0,033 Hz.

3.2.2.2.

The location of the temperature sensor for the soak area shall be representative to measure the ambient temperature around the vehicle and shall be checked by the technical service.

The sensor shall be at least 10 cm away from the wall of the soak area and shall be shielded from direct air flow.

The air-flow conditions within the soak room in the vicinity of the vehicle shall represent a natural convection flow representative for the dimension of the room (no forced convection).

3.3.1.

The vehicle to be tested shall be representative of the family for which the ATCT data are determined (as described in paragraph 2.1. of this Sub-Annex 6a).

3.3.2.

From the ATCT Family, the Interpolation Family with the lowest engine capacity shall be selected (see paragraph 2 of this Sub-Annex 6a), and the test vehicle shall be in the ‘vehicle H’ configuration of this family.

3.3.3.

Where applicable, the vehicle with the lowest enthalpy of the active heat storage device and the slowest heat release for the active heat storage device from the ATCT Family shall be selected.

3.3.4.

The test vehicle shall meet the requirements detailed in paragraph 2.3. of Sub-Annex 6 and paragraph 2.1 of this Sub-Annex 6a.

3.4.1.

Road load and dynamometer settings shall be as specified in Sub-Annex 4, including the requirement for the room temperature to be at 23 °C.

To take account of the difference in air density at 14 °C when compared to the air density at 20 °C, the chassis dynamometer shall be set as specified in paragraphs 7. and 8. of Sub-Annex 4 with the exception that f2_TReg from the following equation shall be used as the target coefficient Ct.

f2_TReg = f2 × (Tref + 273)/(Treg + 273)

where:

f2is the second order road load coefficient, at reference conditions, N/(km/h)2;

Trefis the road load reference temperature as specified in paragraph 3.2.10. of this Annex, C;

Tregis the regional temperature, as defined in paragraph 3.1.1., C.

In the case that a valid chassis dynamometer setting of the 23 °C test is available, the second order chassis dynamometer coefficient of Cd shall be adapted in accordance with the following equation:

Cd_Treg = Cd + (f2_TReg – f2)

3.4.2.

The ATCT test and its road load setting shall be performed on a 2WD dynamometer in the case that the corresponding Type 1 test was done on a 2WD dynamometer; and it shall be performed on a 4WD dynamometer in the case that the corresponding Type 1 test was done on a 4WD dynamometer.

At the request of the manufacturer preconditioning may be undertaken at Treg.

The engine temperature shall be within ± 2 °C of the set point of 23 °C or Treg, whichever temperature is chosen for the preconditioning.

3.5.1.

Pure ICE vehicles shall be preconditioned as described in paragraph 2.6. of Sub-Annex 6.

3.5.2.

NOVC-HEVs shall be preconditioned as described in paragraph 3.3.1.1. of Sub-Annex 8.

3.5.3.

OVC-HEVs shall be preconditioned as described in paragraph 2.1.1. or 2.1.2. of Appendix 4 to Sub-Annex 8.

3.6.1.

After preconditioning and before testing, vehicles shall be kept in a soak area with the ambient conditions described in paragraph 3.2.2. of this Sub-Annex 6a.

3.6.2.

From the end of the preconditioning until the soaking at Treg, the vehicle shall not be exposed to a different temperature than Treg for longer than 10 minutes.

3.6.3.

The vehicle shall then be kept in the soak area such that the time from the end of the preconditioning test to the beginning of the ATCT test is equal to tsoak_ATCT with a tolerance of an additional 15 minutes. At the request of the manufacturer, and upon approval of the approval authority, tsoak_ATCT can be extended by up to 120 minutes. In this case, the extended time shall be used for the cool down specified in paragraph 3.9. of this Sub-Annex 6a.

3.6.4.

The soak shall be performed without using a cooling fan and with all body parts positioned as intended under normal parking operation. The time between the end of the preconditioning and the start of the ATCT test shall be recorded.

3.6.5.

The transfer from the soak area to the test cell shall be undertaken as quickly as possible. The vehicle shall not be exposed to a temperature different from Treg for longer than 10 minutes.

3.7.1.

The test cycle shall be the applicable WLTC specified in Sub-Annex 1 for that class of vehicle.

3.7.2.

The procedures for undertaking the emissions test as specified in Sub-Annex 6 for pure ICE vehicles and in Sub-Annex 8 for NOVC-HEVs and for the charge-sustaining Type 1 test of OVC-HEVs shall be followed, with the exception that the ambient conditions for the test cell shall be those as described in paragraph 3.2.1. of this Sub-Annex 6a.

3.7.3.

In particular, the tailpipe emissions defined by Table A7/1 Step no.1 for pure ICE vehicles and Table A8/5 Step no.2 for HEVs at an ATCT test shall not exceed the Euro 6 emission limits applicable to the vehicle tested defined in Table 2 of Annex I to Regulation (EC) No 715/2007.

3.8.1.

The family correction factor, FCF, shall be calculated as follows:

FCF = MCO2,Treg/MCO2,23°

where

MCO2,23°is the CO2 mass emission of the average of all applicable Type 1 tests at 23 °C of vehicle H, after Step 3 of Table A7/1 of Sub-Annex 7 for pure ICE vehicles and after Step 3 of Table A8/5 for OVC-HEVs and NOVC-HEVs, but without any further corrections, g/km;

MCO2,Tregis the CO2 mass emission over the complete WLTC cycle of the test at regional temperature after Step 3 of Table A7/1 of Sub-Annex 7 for pure ICE vehicles and after Step 3 of Table A8/5 for OVC-HEVs and NOVC-HEVs but without any further corrections, g/km. For OVC-HEVs and NOVC-HEVs, the KCO2 factor as defined in Sub-Annex 8 Appendix 2 shall be used.

Both MCO2,23° and MCO2,Treg shall be measured on the same test vehicle.

The FCF shall be included in all relevant test reports.

The FCF shall be rounded to 4 points of decimal.

3.8.2.

The CO2 values for each pure ICE vehicle within the ATCT Family (as defined in paragraph 2.3. of this Sub-Annex 6a) shall be calculated using the following equations:

MCO2,c,5 = MCO2,c,4 × FCF

MCO2,p,5 = MCO2,p,4 × FCF

where

MCO2,c,4 and MCO2,p,4 are the CO2 mass emissions over the complete WLTC, c, and the cycle phases, p, resulting from the previous calculation step, g/km;

MCO2,c,5 and MCO2,p,5 are the CO2 mass emissions over the complete WLTC, c, and the cycle phases, p, including the ATCT correction, and shall be used for any further corrections or any further calculations, g/km;

3.8.3.

The CO2 values for each OVC-HEV and NOVC-HEV within the ATCT Family (as defined in paragraph 2.3. of this Sub-Annex 6a) shall be calculated using the following equations:

MCO2,CS,c,5 = MCO2,CS,c,4 × FCF

MCO2,CS,p,5 = MCO2,CS,p,4 × FCF

where

MCO2,CS,c,4 and MCO2,CS,p,4 are the CO2 mass emissions over the complete WLTC, c, and the cycle phases, p, resulting from the previous calculation step, g/km;

MCO2,CS,c,5 and MCO2,CS,p,5 are the CO2 mass emissions over the complete WLTC, c, and the cycle phases, p, including the ATCT correction, and shall be used for any further corrections or any further calculations, g/km.

3.8.4.

If a FCF is less than one, it is deemed to be equal to one, in the case of the worstcase approach, in accordance with paragraph 4.1 of this Sub-Annex.

3.9.1.

For the test vehicle serving as a reference vehicle for the ATCT Family and all vehicles H of the interpolation families within the ATCT Family, the end temperature of the engine coolant shall be measured after soaking at 23 °C for the duration of tsoak_ATCT, with a tolerance of an additional 15 minutes, having beforehand driven the respective Type 1 test at 23 °C. The duration is measured from the end of that respective Type 1 test.

3.9.1.1.

In the case that tsoak_ATCT was extended in the respective ATCT test, the same soaking time shall be used, with a tolerance of an additional 15 minutes.

3.9.2.

The cool down procedure shall be undertaken as soon as possible after the end of the Type 1 test, with a maximum delay of 20 minutes. The measured soaking time is the time between the measurement of the end temperature and the end of the Type 1 test at 23 °C, and shall be included in all relevant test sheets.

3.9.3.

The average temperature of the soak area of the last 3 hours shall be subtracted from the measured temperature of the engine coolant at the end of the soaking time specified in paragraph 3.9.1. This is referred to as ΔT_ATCT, rounded to the nearest whole number.

3.9.4.

If ΔT_ATCT is higher or equal than – 2 °C from the test vehicle ΔT_ATCT, this Interpolation Family shall be considered to be a member of the same ATCT Family.

3.9.5.

For all vehicles within an ATCT Family the coolant shall be measured at the same location in the cooling system. That location shall be as close as possible to the engine so that the coolant temperature is as representative as possible to the engine temperature.

3.9.6.

The measurement of the temperature of the soak areas shall be as specified in paragraph 3.2.2.2. of this Sub-Annex 6a.

On request by the manufacturer and with approval by the approval authority, the Type 1 Test procedure for cool down may be applied instead of provisions of paragraph 3.6 of this Sub-Annex 6a. For that purpose:

(a)

The provisions of paragraph 2.7.2. of Sub-Annex 6 shall apply with the additional requirement of a minimum soak time of 9 hours.

(b)

The engine temperature shall be within ± 2 °C of the set point Treg before the start of the ATCT test. That temperature shall be included in all relevant test sheets. In this case, the provision for cool down described in paragraph 3.9. of this Sub-Annex 6a and the criteria on engine compartment insulation can be skipped for all vehicles in the family.

This alternative is not allowed if the vehicle is equipped with an active heat storage device.

The application of that approach shall be included in all relevant test reports.

In the case, that the ATCT family consists of only one interpolation family, the provision for cool down described in paragraph 3.9. of this Sub-Annex 6a can be skipped. This shall be included in all relevant test reports.

In the case that measuring the coolant temperature is not feasible, on request of the manufacturer and with approval of the approval authority, instead of using the coolant temperature for the provision for cool down described in paragraph 3.9. of this Sub-Annex 6a, the engine oil temperature may be used. In that case, for all vehicles within the family the engine oil temperature shall be used.

The application of that procedure shall be included in all relevant test reports.

Changed on 1 Jan 2019

This Appendix describes the procedure to correct the charge-sustaining Type 1 test CO2 mass emission for NOVC-HEVs and OVC-HEVs, and the fuel consumption for NOVC-FCHVs as a function of the electric energy change of all REESSs. 1.1.1. The phase-specific fuel consumption for NOVC-FCHVs, and the CO2 mass emission for NOVC-HEVs and OVC-HEVs shall be corrected. 1.1.2. In the case that a correction of fuel consumption for NOVC-FCHVs or a correction of CO2 mass emission for NOVC-HEVs and OVC-HEVs measured over the whole cycle according to paragraph 1.1.3. or paragraph 1.1.4. of this Appendix is applied, paragraph 4.3. of this Sub-Annex shall be used to calculate the charge-sustaining REESS energy change ΔEREESS,CS of the charge-sustaining Type 1 test. The considered period j used in paragraph 4.3. of this Sub-Annex is defined by the charge-sustaining Type 1 test. 1.1.3. The correction shall be applied if ΔEREESS,CS is negative which corresponds to REESS discharging and the correction criterion c calculated in paragraph 1.2. is greater than the applicable tolerance according to Table A8.App2/1. 1.1.4. The correction may be omitted and uncorrected values may be used if: (a) ΔEREESS,CS is positive which corresponds to REESS charging and the correction criterion c calculated in paragraph 1.2. is greater than the applicable tolerance according to Table A8.App2/1; (b) the correction criterion c calculated in paragraph 1.2. is smaller than the applicable tolerance according to Table A8.App2/1; (c) the manufacturer can prove to the approval authority by measurement that there is no relation between ΔEREESS,CS and charge-sustaining CO2 mass emission and ΔEREESS,CS and fuel consumption respectively. 1.2. The correction criterion c is the ratio between the absolute value of the REESS electric energy change ΔEREESS,CS and the fuel energy and shall be calculated as follows: c ΔEREESS,CS Efuel,CS where: ΔEREESS,CSis the charge-sustaining REESS energy change according to paragraph 1.1.2. of this Appendix, Wh; Efuel,CSis the charge-sustaining energy content of the consumed fuel according to paragraph 1.2.1. in the case of describes the supplemental Ambient Temperature Correction Test (ATCT) procedure to determine the CO2 emissions under representative regional temperature conditions. 1.1. The CO2 emissions of ICE vehicles, NOVC-HEVs and OVC-HEVs, according to paragraph 1.2.2. in the case of NOVC-FCHVs, Wh. The the charge- sustaining energy content of the consumed fuel for NOVC-HEVs and value of OVC-HEVs shall be calculated using the following equation: Efuel,CS10 HV FCCS,nb dCS where: Efuel,CSis the charge-sustaining energy content of the consumed fuel of the applicable WLTP test cycle of the charge-sustaining Type 1 test, Wh; HVis the heating value according to Table A6.App2/1, kWh/l; FCCS,nbis the non-balanced charge-sustaining fuel consumption of the charge-sustaining Type 1 test, not corrected for the energy balance, determined according to paragraph 6. of corrected in accordance with the requirements of this Sub-Annex 7, using the gaseous emission compound values according to Table A8/5, step no. 2, l/100 km; dCSis the distance driven over the corresponding applicable WLTP test cycle, km; 10conversion factor to Wh. The charge-sustaining energy content of the consumed fuel for NOVC-FCHVs shall be calculated using the following equation: Efuel,CS10,36 121 FCCS,nb dCS Efuel,CSis the charge-sustaining energy content of the consumed fuel of the applicable WLTP test cycle of the charge-sustaining Type 1 test, Wh; 121is the lower heating . No correction is required for the CO2 value of hydrogen, MJ/kg; FCCS,nbis the non-balanced the charge-sustaining fuel consumption of the charge-sustaining Type 1 depleting test, not corrected for the energy balance, determined according to Table A8/7, step no.1, kg/100 km; dCSis the distance driven over the corresponding applicable WLTP test cycle, km; 10,36conversion factor to Wh. Applicable Type 1 test cycle | Low + Medium | Low + Medium + High | Low + Medium + High + Extra High Correction criterion ratio c | 0,015 | 0,01 | 0,005. No correction is required for an Electric Range.

The CO2 mass emission correction coefficient KCO2, the Only vehicles which are identical with respect to all the following characteristics are permitted to be part of the same ATCT Family: (a) Powertrain architecture (i.e. internal combustion, hybrid, fuel consumption correction coefficients Kfuel,FCHV, as well as, if required by the manufacturer, the phase-specific correction coefficients KCO2,p and Kfuel,FCHV,p cell, or electric); (b) Combustion process (i.e. two stroke or four stroke); (c) Number and arrangement of cylinders; (d) Method of engine combustion (i.e. indirect or direct injection); (e) Type of cooling system (i.e. air, water, or oil); (f) Method of aspiration (i.e. naturally aspirated, or charged); (g) Fuel for which the engine is designed (i.e. petrol, diesel, NG, LPG, etc.); (h) Catalytic converter (i.e. three-way catalyst, lean NOx trap, SCR, lean NOx catalyst or other(s)); (i) Whether or not a particulate trap is installed; and (j) Exhaust gas recirculation (with or without, cooled or non-cooled). In addition the vehicles shall be developed based on the applicable charge-sustaining Type 1 test cycles. In the case that vehicle H was tested for the development similar with respect to the following characteristics: (k) The vehicles shall have a variation in engine cylinder capacity of no more than 30 % of the vehicle with the lowest capacity; and (l) Engine compartment insulation shall be of a similar type regarding material, amount and location of the insulation. Manufacturers shall provide evidence (e.g. by CAD drawings) to the approval authority that for all vehicles in the family, the volume and weight of the correction coefficient for CO2 mass emission for NOVC-HEVs and OVC-HEVs, the coefficient may be applied within the interpolation insulation material which will be installed is greater than 90 % of that of the ATCT measured reference vehicle. Difference in insulation material and location may also be accepted to be part of a single ATCT family under the condition that the test vehicle can be demonstrated as being the worst case with regards to engine compartment insulation. 2.2. The correction coefficients shall be determined from a set of charge-sustaining Type 1 tests according to paragraph 3. of this Appendix. The number of tests performed 1.1. If active heat storage devices are installed, only vehicles that meet the following requirements shall be considered to be part of the same ATCT Family: (i) the heat capacity, defined by the manufacturer shall be equal to or greater than five. The manufacturer may request to set the state of charge of the REESS prior to enthalpy stored in the system, is within a range of 0 to 10 % above the enthalpy of the test vehicle; and (ii) the OEM can provide evidence to the technical service that the time for heat release at engine start within a family is within a range of 0 to 10 % below the time for the heat release of the test according to the manufacturer’s recommendation and as describedvehicle. 2.1.2. Only vehicles that meet the criteria set out in paragraph 3.9.4. of this Appendix. This practice Sub-Annex 6a shall only be used for the purpose of achieving a charge-sustaining be considered to be part of the same ATCT Family. The Type 1 test specified in Sub-Annex 6 shall be carried out with opposite signthe exception of the ΔEREESS,CS and requirements specified in paragraphs 3.1. to 3.9. of this Sub-Annex 6a. That requires also a new calculation and application of gearshift points in accordance with approval of the approval authority. The set of measurements shall fulfil the following criteria: (a) The set Sub-Annex 2 taking into account the different road load as specified in paragraph 3.4. of this Sub-Annex 6a. 3.1.1. The temperature (Treg) at which the vehicle should be soaked and tested for the ATCT shall be 14 °C. 3.1.2. The minimum soaking time (tsoak_ATCT) for the ATCT shall be 9 hours. 3.2.1.1. The test cell shall contain at least one test with ΔEREESS,CS ≤ 0 and at least one have a temperature set point equal to Treg. The actual temperature value shall be within ± 3 °C at the start of the test with ΔEREESS,CS > 0. ΔEREESS,CS,n is the sum of electric energy changes of all REESSs of test n calculated according to paragraph 4.3. of this Sub-Annex. (b) The difference in MCO2,CS between the test with the highest negative electric energy change and the test with the highest positive electric energy change and within ± 5 °C during the test. 3.2.1.2. The specific humidity (H) of either the air in the test cell or the intake air of the engine shall be such that: 3,0 ≤ H ≤ 8,1 | (g H2O/kg dry air) 3.2.1.3. The air temperature and humidity shall be measured at the cooling fan outlet at a rate of 0,1 Hz. 3.2.2.1. The soak area shall have a temperature set point equal to Treg and the actual temperature value shall be within ± 3 °C on a 5 minute running arithmetic average and shall not show a systematic deviation from the set point. The temperature shall be measured continuously at a minimum frequency of 0,033 Hz. 3.2.2.2. The location of the temperature sensor for the soak area shall be greater than or equal to 5 g/km. This criterion representative to measure the ambient temperature around the vehicle and shall not be applied for the determination of Kfuel,FCHV. In the case of the determination of KCO2, the required number of tests may be reduced to three tests if all be checked by the technical service. The sensor shall be at least 10 cm away from the wall of the soak area and shall be shielded from direct air flow. The air-flow conditions within the soak room in the vicinity of the vehicle shall represent a natural convection flow representative for the dimension of the room (no forced convection). 3.3.1. The vehicle to be tested shall be representative of the following criteria are fulfilled in addition to (a) and (b): (c) the difference in MCO2,CS between any two adjacent measurements, related to the electric energy change during the family for which the ATCT data are determined (as described in paragraph 2.1. of this Sub-Annex 6a). 3.3.2. From the ATCT Family, the Interpolation Family with the lowest engine capacity shall be selected (see paragraph 2 of this Sub-Annex 6a), and the test vehicle shall be in the ‘vehicle H’ configuration of this family. 3.3.3. Where applicable, the vehicle with the lowest enthalpy of the active heat storage device and the slowest heat release for the active heat storage device from the ATCT Family shall be selected. 3.3.4. The test, vehicle shall be less than or equal to 10 g/km. (d) in addition to (b)meet the requirements detailed in paragraph 2.3. of Sub-Annex 6 and paragraph 2.1 of this Sub-Annex 6a. 3.4.1. Road load and dynamometer settings shall be as specified in Sub-Annex 4, including the requirement for the room temperature to be at 23 °C. To take account of the difference in air density at 14 °C when compared to the air density at 20 °C, the test with the highest negative electric energy change and the test chassis dynamometer shall be set as specified in paragraphs 7. and 8. of Sub-Annex 4 with the highest positive electric energy change shall not be within the region that is defined by: 0,01ΔEREESSEfuel 0,01,exception that f2_TReg from the following equation shall be used as the target coefficient Ct. f2_TReg = f2 × (Tref + 273)/(Treg + 273)

Efuelis the energy content of the consumed fuel calculated according to f2is the second order road load coefficient, at reference conditions, N/(km/h)2; Trefis the road load reference temperature as specified in paragraph 1.2.3.2.10. of this Appendix, Wh. (e) the difference in MCO2,CS between the test with the highest negative electric energy change and the mid-point, and the difference in MCO2,CS between mid-point and the test with the highest positive electric energy change Annex, C; Tregis the regional temperature, as defined in paragraph 3.1.1., C. In the case that a valid chassis dynamometer setting of the 23 °C test is available, the second order chassis dynamometer coefficient of Cd shall be similar and preferably be within the range defined by (d). The correction coefficients determined by the manufacturer adapted in accordance with the following equation: Cd_Treg = Cd + (f2_TReg – f2) 3.4.2. The ATCT test and its road load setting shall be reviewed and approved by the approval authority prior to its application. If the set of at least five tests does not fulfil criterion (a) or criterion (b) or both, the manufacturer shall provide evidence to the approval authority as to why the vehicle is not capable of meeting either or both criteria. If the approval authority is not satisfied with the evidence, it may require additional tests to be performed. If the criteria after additional tests are still not fulfilled, the approval authority will determine a conservative correction coefficient, based on the measurements. For NOVC-FCHVs, the fuel consumption correction coefficient Kfuel,FCHV, determined by driving a set of charge-sustaining Type 1 tests, is defined using the following equation: Kfuel,FCHV nCS n 1 ECDC,CS,n ECDC,CS,avg FCCS,nb,n FCCS,nb,avg nCS n 1 ECDC,CS,n ECDC,CS,avg2 where: Kfuel,FCHVis the fuel consumption correction coefficient, (kg/100 km)/(Wh/km); ECDC,CS,nis the charge-sustaining electric energy consumption of test n based on the REESS depletion according to the equation below, Wh/km ECDC,CS,avgis the mean charge-sustaining electric energy consumption of ncs tests based on the REESS depletion according to the equation below, Wh/km; FCCS,nb,nis the charge-sustaining fuel consumption ofperformed on a 2WD dynamometer in the case that the corresponding Type 1 test was done on a 2WD dynamometer; and it shall be performed on a 4WD dynamometer in the case that the corresponding Type 1 test was done on a 4WD dynamometer. At the request of the manufacturer preconditioning may be undertaken at Treg. The engine temperature shall be within ± 2 °C of the set point of 23 °C or Treg, whichever temperature is chosen for the preconditioning. 3.5.1. Pure ICE vehicles shall be preconditioned as described in paragraph 2.6. of Sub-Annex 6. 3.5.2. NOVC-HEVs shall be preconditioned as described in paragraph 3.3.1.1. of Sub-Annex 8. 3.5.3. OVC-HEVs shall be preconditioned as described in paragraph 2.1.1. or 2.1.2. of Appendix 4 to Sub-Annex 8. 3.6.1. After preconditioning and before testing, vehicles shall be kept in a soak area with the ambient conditions described in paragraph 3.2.2. of this Sub-Annex 6a. 3.6.2. From the end of the preconditioning until the soaking at Treg, the vehicle shall not be exposed to a different temperature than Treg for longer than 10 minutes. 3.6.3. The vehicle shall then be kept in the soak area such that the time from the end of the preconditioning test n, not corrected for the energy balance, according to Table A8/7, step no. 1, kg/100 km; FCCS,nb,avgis the arithmetic average of the charge-sustaining fuel consumption of ncs tests based on the fuel consumption, not corrected for the energy balance, according to the equation below, kg/100 km; nis the index number of the considered test; ncsis the total number of tests; and: ECDC,CS,avg1ncs ncs n 1 ECDC,CS,n and: FCCS,nb,avg1ncs ncs n 1 FCCS,nb,n and: ECDC,CS,nΔEREESS,CS,ndCS,n where: ΔEREESS,CS,nis the charge-sustaining REESS electric energy change of test n according to paragraph 1.1.2. of this Appendix, Wh; dCS,nis the distance driven over the corresponding charge-sustaining Type 1to the beginning of the ATCT test is equal to tsoak_ATCT with a tolerance of an additional 15 minutes. At the request of the manufacturer, and upon approval of the approval authority, tsoak_ATCT can be extended by up to 120 minutes. In this case, the extended time shall be used for the cool down specified in paragraph 3.9. of this Sub-Annex 6a. 3.6.4. The soak shall be performed without using a cooling fan and with all body parts positioned as intended under normal parking operation. The time between the end of the preconditioning and the start of the ATCT test n, km. The fuel consumption correction coefficient shall be recorded. 3.6.5. The transfer from the soak area to the test cell shall be rounded to four significant figuresundertaken as quickly as possible. The statistical significance of the fuel consumption correction coefficient shall be evaluated by the approval authority. 2.3.1.1. It is permitted to apply the fuel consumption correction coefficient that was developed from tests over the whole applicable WLTP test cycle for the correction of each individual phase. 2.3.1.2. Without prejudice to the requirements of paragraph 2.2. of this Appendix, at the manufacturer’s request and upon approval of the approval authority, separate fuel consumption correction coefficients Kfuel,FCHV,p for each individual phase may be developed. In this case, the same criteria vehicle shall not be exposed to a temperature different from Treg for longer than 10 minutes. 3.7.1. The test cycle shall be the applicable WLTC specified in Sub-Annex 1 for that class of vehicle. 3.7.2. The procedures for undertaking the emissions test as specified in Sub-Annex 6 for pure ICE vehicles and in Sub-Annex 8 for NOVC-HEVs and for the charge-sustaining Type 1 test of OVC-HEVs shall be followed, with the exception that the ambient conditions for the test cell shall be those as described in paragraph 2.2.3.2.1. of this Appendix shall be fulfilled in each individual phase and the procedure described in paragraph 2.3.1. of this Appendix shall be applied for each individual phase to determine each phase specific correction coefficient. For OVC-HEVs and NOVC-HEVs, the CO2 massSub-Annex 6a. 3.7.3. In particular, the tailpipe emissions defined by Table A7/1 Step no.1 for pure ICE vehicles and Table A8/5 Step no.2 for HEVs at an ATCT test shall not exceed the Euro 6 emission correction coefficient KCO2, determined by driving a set of charge-sustaining Type 1 tests, is defined by the following equation: KCO2 nCS n 1 ECDC,CS,n ECDC,CS,avg MCO2,CS,nb,n MCO2,CS,nb,avg nCS n 1 ECDC,CS,n ECDC,CS,avg2limits applicable to the vehicle tested defined in Table 2 of Annex I to Regulation (EC) No 715/2007. 3.8.1. The family correction factor, FCF, shall be calculated as follows: FCF = MCO2,Treg/MCO2,23° where: KCO2is MCO2,23°is the CO2 mass emission correction coefficient, (g/km)/(Wh/km); ECDC,CS,nis the charge-sustaining electric energy consumption of test n based on the REESS depletion according to paragraph 2.3.1. of this Appendix, Wh/km; ECDC,CS,avgis the arithmetic average of the charge-sustaining electric energy consumption of ncs tests based on the REESS depletion according to paragraph 2.3.1. of this Appendix, Whof the average of all applicable Type 1 tests at 23 °C of vehicle H, after Step 3 of Table A7/1 of Sub-Annex 7 for pure ICE vehicles and after Step 3 of Table A8/5 for OVC-HEVs and NOVC-HEVs, but without any further corrections, g/km; MCO2,CS,nb,nis the charge-sustaining Tregis the CO2 mass emission of test n, not corrected for the energy balance, calculated according Table A8/5, step no. 2, g/km; MCO2,CS,nb,avgis the arithmetic average of the charge-sustaining CO2 mass emission of ncs tests based on the CO2 mass emission, not corrected for the energy balance, according to the equation belowover the complete WLTC cycle of the test at regional temperature after Step 3 of Table A7/1 of Sub-Annex 7 for pure ICE vehicles and after Step 3 of Table A8/5 for OVC-HEVs and NOVC-HEVs but without any further corrections, g/km; nis the index number of the considered test; ncsis the total number of tests; and: MCO2,CS,nb,avg1nCS ncs n 1 MCO2,CS,nb,n The CO2 mass emission correction coefficient. For OVC-HEVs and NOVC-HEVs, the KCO2 factor as defined in Sub-Annex 8 Appendix 2 shall be used. Both MCO2,23° and MCO2,Treg shall be rounded to four significant figures. The statistical significance of the CO2 mass emission correction coefficient measured on the same test vehicle. The FCF shall be included in all relevant test reports. The FCF shall be evaluated by the approval authority. 2.3.2.1. It is permitted to apply the CO2 mass emission correction coefficient developed from tests over the whole applicable WLTP test cycle for the correction of each individual phase. rounded to 4 points of decimal. 3.8.2. The CO2 values for each pure ICE vehicle within the ATCT Family (as defined in paragraph 2.3.2.2. Without prejudice to the requirements of paragraph 2.2. of this Appendix, at the request of the manufacturer upon approval of the approval authority, separate of this Sub-Annex 6a) shall be calculated using the following equations: MCO2,c,5 = MCO2,c,4 × FCF MCO2,p,5 = MCO2,p,4 × FCF where MCO2,c,4 and MCO2,p,4 are the CO2 mass emission correction coefficients KCO2,p for each individual phase may be developed. In this case, the same criteria as described in paragraph 2.2. of this Appendix shall be fulfilled in each individual phase emissions over the complete WLTC, c, and the cycle phases, p, resulting from the previous calculation step, g/km; MCO2,c,5 and MCO2,p,5 are the CO2 mass emissions over the complete WLTC, c, and the procedure described in paragraph 2.3.2. of this Appendixcycle phases, p, including the ATCT correction, and shall be applied for each individual phase to determine phase-specific correction coefficients. For used for any further corrections or any further calculations, g/km; 3.8.3. The CO2 values for each OVC-HEVs, one of the following test sequences according to Figure A8.App2/1 HEV and NOVC-HEV within the ATCT Family (as defined in paragraph 2.3. of this Sub-Annex 6a) shall be used to measure all values that are necessary for the determination of the correction coefficients according to paragraph 2. of this Appendix. Preconditioning and soaking shall be conducted according to paragraph 2.1. of Appendix 4. to this Sub-Annex. Prior to the test procedure according to paragraph 3.1.1.3. the manufacturer may adjust the REESS. The manufacturer shall provide evidence that the requirements for the beginning of the test according to paragraph 3.1.1.3. are fulfilledcalculated using the following equations: MCO2,CS,c,5 = MCO2,CS,c,4 × FCF MCO2,CS,p,5 = MCO2,CS,p,4 × FCF where MCO2,CS,c,4 and MCO2,CS,p,4 are the CO2 mass emissions over the complete WLTC, c, and the cycle phases, p, resulting from the previous calculation step, g/km; MCO2,CS,c,5 and MCO2,CS,p,5 are the CO2 mass emissions over the complete WLTC, c, and the cycle phases, p, including the ATCT correction, and shall be used for any further corrections or any further calculations, g/km. 3.1.1.3.1. The driver-selectable mode for the applicable WLTP test cycle shall be selected according to paragraph 3. of Appendix 6 to this Sub-Annex. 3.1.1.3.2. For testing, the applicable WLTP test cycle according to 8.4. If a FCF is less than one, it is deemed to be equal to one, in the case of the worstcase approach, in accordance with paragraph 1.4.2.4.1 of this Sub-Annex shall be driven. 3.1.1.3.3. Unless stated otherwise in this Appendix, the9.1. For the test vehicle serving as a reference vehicle shall be tested according to the Type 1 test procedure described in Sub-Annex 6. 3.1.1.3.4. To obtain a set of applicable WLTP test cycles required for the determination of the correction coefficients, the test may be followed by a number of consecutive sequences required according to paragraph 2.2 of this Appendix consisting of paragraph 3.1.1.1. to paragraph 3.1.1.3. inclusive of this Appendix. The test vehicle shall be preconditioned according to paragraph 2.1.1. or paragraph 2.1.2. of Appendix 4 to this Sub-Annex. After preconditioning, soaking according to paragraph 2.1.3. of Appendix 4 to this Sub-Annex shall be omitted and a break, during which the REESS is permitted to be adjusted, shall be set to a maximum duration of 60 for the ATCT Family and all vehicles H of the interpolation families within the ATCT Family, the end temperature of the engine coolant shall be measured after soaking at 23 °C for the duration of tsoak_ATCT, with a tolerance of an additional 15 minutes, having beforehand driven the respective Type 1 test at 23 °C. The duration is measured from the end of that respective Type 1 test. 3.9.1.1. In the case that tsoak_ATCT was extended in the respective ATCT test, the same soaking time shall be used, with a tolerance of an additional 15 minutes. A similar break 3.9.2. The cool down procedure shall be applied in advance of each test. Immediately undertaken as soon as possible after the end of this break, the requirements of paragraph 3.1.2.3. of this Appendix shall be applied. Upon request of the manufacturer, an additional warm-up procedure may be conducted in advance the Type 1 test, with a maximum delay of 20 minutes. The measured soaking time is the time between the measurement of the REESS adjustment to ensure similar starting conditions for the correction coefficient determination. If the manufacturer requests this additional warm-up procedure, the identical warm-up procedure end temperature and the end of the Type 1 test at 23 °C, and shall be applied repeatedly within theincluded in all relevant test sequencesheets. 3.1.2.3.1. The driver-selectable mode for the applicable WLTP test cycle 9.3. The average temperature of the soak area of the last 3 hours shall be selected according to paragraph 3. of Appendix 6 to this Sub-Annex. 3.1.2.3.2. For testing, the applicable WLTP test cycle according to subtracted from the measured temperature of the engine coolant at the end of the soaking time specified in paragraph 1.4.2. of this Sub-Annex shall be driven. 3.1.2.3.3. Unless stated otherwise in this Appendix, the vehicle shall be tested according 3.9.1. This is referred to as ΔT_ATCT, rounded to the Type 1 test procedure described in Sub-Annex 6nearest whole number. 3.1.2.3.4. To obtain a set of applicable WLTP test cycles that are required for the determination of the correction coefficients, the test may be followed by a number of consecutive sequences required according to paragraph 2.2. of this Appendix consisting of paragraphs 3.1.2.2. and 3.1.2.3. of this Appendix. For NOVC-HEVs and NOVC-FCHVs, one of the following test sequences according to Figure A8.App2/2 shall be used to measure all values9.4. If ΔT_ATCT is higher or equal than – 2 °C from the test vehicle ΔT_ATCT, this Interpolation Family shall be considered to be a member of the same ATCT Family. 3.9.5. For all vehicles within an ATCT Family the coolant shall be measured at the same location in the cooling system. That location shall be as close as possible to the engine so that are necessary for the determination of the correction coefficients according to paragraph 2. of this Appendix. The test vehicle the coolant temperature is as representative as possible to the engine temperature. 3.9.6. The measurement of the temperature of the soak areas shall be preconditioned and soaked according to as specified in paragraph 3.3.1.2.2.2. of this Sub-Annex. Prior to the test procedure, according to paragraph 3.2.1.3., 6a. On request by the manufacturer may adjust the REESS. The manufacturer shall provide evidence that the requirements for the beginning of the test according to paragraph 3.2.1.3. are fulfilled. 3.2.1.3.1. The driver-selectable mode shall be selected according to and with approval by the approval authority, the Type 1 Test procedure for cool down may be applied instead of provisions of paragraph 3. of Appendix 6 to 6 of this Sub-Annex. 3.2.1.3.2. For testing, the applicable WLTP test cycle according to 6a. For that purpose: (a) The provisions of paragraph 1.42.7.2. of this Sub-Annex shall be driven. 3.2.1.3.3. Unless stated otherwise in this Appendix, the vehicle 6 shall be tested according to the charge-sustaining Type 1 test procedure described in Sub-Annex 6. 3.2.1.3.4. To obtain a set of applicable WLTP test cycles that are required for the determination of the correction coefficients, the test can be followed by a number of consecutive sequences required according to paragraph 2.2. of this Appendix consisting of paragraph 3.2.1.1. to paragraph 3.2.1.3. inclusive of apply with the additional requirement of a minimum soak time of 9 hours. (b) The engine temperature shall be within ± 2 °C of the set point Treg before the start of the ATCT test. That temperature shall be included in all relevant test sheets. In this Appendix. The test vehicle shall be preconditioned according tocase, the provision for cool down described in paragraph 3.3.1.1.9. of this Sub-Annex. After preconditioning, the soaking according to paragraph 3.3.1.2. of this Sub-Annex shall be omitted and a break, during which the REESS is permitted to be adjusted, shall be set to a maximum duration of 60 minutes. A similar break 6a and the criteria on engine compartment insulation can be skipped for all vehicles in the family. This alternative is not allowed if the vehicle is equipped with an active heat storage device. The application of that approach shall be applied in advance of each included in all relevant test. Immediately after the end of this break reports. In the case, that the ATCT family consists of only one interpolation family, the requirements of provision for cool down described in paragraph 3.2.2.3.9. of this Appendix shall be applied. Upon request of the manufacturer, an additional warm-up procedure may be conducted in advance of the REESS adjustment to ensure similar starting conditions for the correction coefficient determination. If the Sub-Annex 6a can be skipped. This shall be included in all relevant test reports. In the case that measuring the coolant temperature is not feasible, on request of the manufacturer requests this additional warm-up procedure, the identical warm-up procedure shall be applied repeatedly within the test sequence. 3.2.2.3.1. The driver-selectable mode and with approval of the approval authority, instead of using the coolant temperature for the applicable WLTP test cycle shall be selected according to provision for cool down described in paragraph 3. of Appendix 6 to 9. of this Sub-Annex. 3.2.2.3.2. For testing 6a, the applicable WLTP test cycle according to paragraph 1.4.2. of this Sub-Annex shall be driven. 3.2.2.3.3. Unless stated otherwise in this Appendix, the vehicle shall be tested according to the Type 1 test procedure described in Sub-Annex 6. 3.2.2.3.4. To get a set of applicable WLTP test cycles engine oil temperature may be used. In that case, for all vehicles within the family the engine oil temperature shall be used. The application of that are required for the determination of the correction coefficients, the procedure shall be included in all relevant test can be followed by a number of consecutive sequences required according to paragraph 2.2. of this Appendix consisting of paragraphs 3.2.2.2. and 3.2.2.3. of this Appendix.reports.

  1. 1 Jan 2019 – 1 Sep 2023earlier wording
  2. 27 Jul 2017 – 1 Jan 2019earlier wording
  3. 1 Jun 2017 – 27 Jul 2017earlier wording