68 Sub-Annex 6 - Appendix 2, Regulation (EU) 2017/1151

No longer in force

In the case that NOVC-HEVs and OVC-HEVs are tested, Appendices 2 and 3 to Sub-Annex 8 shall apply.

This Appendix defines the specific provisions regarding the correction of test results for CO2 mass emission as a function of the energy balance ΔEREESS for all REESSs.

The corrected values for CO2 mass emission shall correspond to a zero energy balance (ΔEREESS = 0), and shall be calculated using a correction coefficient determined as defined below.

REESS depletion shall be defined as negative current.

2.1.1.

The REESS current(s) shall be measured during the tests using a clamp-on or closed type current transducer. The current measurement system shall fulfil the requirements specified in Table A8/1. The current transducer(s) shall be capable of handling the peak currents at engine starts and temperature conditions at the point of measurement.

In order to have an accurate measurement, zero adjustment and degaussing shall be performed before the test in accordance with the instrument manufacturer's instructions.

2.1.2.

Current transducers shall be fitted to any of the REESS on one of the cables connected directly to the REESS and shall include the total REESS current.

In case of shielded wires, appropriate methods shall be applied in accordance with the approval authority.

In order to easily measure REESS current using external measuring equipment, manufacturers should preferably integrate appropriate, safe and accessible connection points in the vehicle. If this is not feasible, the manufacturer shall support the approval authority by providing the means to connect a current transducer to the REESS cables in the manner described above.

2.1.3.

The measured current shall be integrated over time at a minimum frequency of 20 Hz, yielding the measured value of Q, expressed in ampere-hours Ah. The measured current shall be integrated over time, yielding the measured value of Q, expressed in ampere-hours Ah. The integration may be done in the current measurement system.

2.2.1.

Alternatively, the REESS current shall be determined using vehicle-based data. In order to use this measurement method, the following information shall be accessible from the test vehicle:

(a)

Integrated charging balance value since last ignition run in Ah;

(b)

Integrated on-board data charging balance value calculated at a minimum sample frequency of 5 Hz;

(c)

The charging balance value via an OBD connector as described in SAE J1962.

2.2.2.

The accuracy of the vehicle on-board REESS charging and discharging data shall be demonstrated by the manufacturer to the approval authority.

The manufacturer may create a REESS monitoring vehicle family to prove that the vehicle on-board REESS charging and discharging data are correct. The accuracy of the data shall be demonstrated on a representative vehicle.

The following family criteria shall be valid:

(a)

Identical combustion processes (i.e. positive ignition, compression ignition, two-stroke, four-stroke);

(b)

Identical charge and/or recuperation strategy (software REESS data module);

(c)

On-board data availability;

(d)

Identical charging balance measured by REESS data module;

(e)

Identical on-board charging balance simulation.

2.2.3.

All REESS having no influence on CO2 mass emissions shall be excluded from monitoring.

3.1.

Measurement of the REESS current shall start at the same time as the test starts and shall end immediately after the vehicle has driven the complete driving cycle.

3.2.

The electricity balance Q measured in the electric power supply system, shall be used as a measure of the difference in the REESS energy content at the end of the cycle compared to the beginning of the cycle. The electricity balance shall be determined for the total driven WLTC.

3.3.

Separate values of Qphase shall be logged over the driven cycle phases.

The correction criterion c is the ratio between the absolute value of the electric energy change ΔEREESS,j and the fuel energy and shall be calculated using the following equations:

cΔEREESS,jEfuel

where:

cis the correction criterion;

ΔEREESS,jis the electric energy change of all REESSs over period j determined in accordance with paragraph 4.1. of this Appendix, Wh;

jis, in this paragraph, the whole applicable WLTP test cycle;

EFuel

is the fuel energy calculated with the following equation:

Efuel = 10 × HV × FCnb × d

where:

Efuelis the energy content of the consumed fuel over the applicable WLTP test cycle, Wh;

HVis the heating value in accordance with Table A6.App2/1, kWh/l;

FCnbis the non-balanced fuel consumption of the Type 1 test, not corrected for the energy balance, determined in accordance with paragraph 6. of Sub-Annex 7, and using the results for criteria emissions and CO2 calculated in Step 2 in Table A7/1, l/100 km;

dis the distance driven over the corresponding applicable WLTP test cycle, km;

10conversion factor to Wh.

3.4.2.

The correction shall be applied if ΔEREESS is negative (corresponding to REESS discharging) and the correction criterion ‘c’ calculated in accordance with paragraph 3.4.1. of this Appendix is greater than the applicable threshold in accordance with Table A6.App2/2.

3.4.3.

The correction shall be omitted and uncorrected values shall be used if the correction criterion ‘c’ calculated in accordance with paragraph 3.4.1. of this Appendix is less than the applicable threshold in accordance with Table A6.App2/2.

3.4.4.

The correction may be omitted and uncorrected values may be used if:

(a)

ΔEREESS is positive (corresponding to REESS charging) and the correction criterion ‘c’ calculated in accordance with paragraph 3.4.1. of this Appendix is greater than the applicable threshold in accordance with Table A6.App2/2;

(b)

the manufacturer can prove to the approval authority by measurement that there is no relation between ΔEREESS and CO2 mass emission and ΔEREESS and fuel consumption respectively.

Fuel | Petrol | Diesel

Content Ethanol/Biodiesel, per cent | | | E10 | | | E85 | | | | B7 | |

Heat value

(kWh/l)

8,64 | | | 6,41 | | | | 9,79 | |

Cycle | low + medium) | low + medium + high | low + medium + high + extra high

Thresholds for correction criterion c | 0,015 | 0,01 | 0,005

4.1.

To apply the correction function, the electric energy change ΔTREESS,j of a period j of all REESSs shall be calculated from the measured current and the nominal voltage:

ΔEREESS,j

ni1

ΔEREESS,j,i

where:

ΔEREESS,j,iis the electric energy change of REESS i during the considered period j, Wh;

and:

ΔEREESS,j,i1

3600

UREESS

tendt0

It j,idt

where:

UREESSis the nominal REESS voltage determined in accordance with IEC 60050-482, V;

I(t)j,iis the electric current of REESS i during the considered period j, determined in accordance with paragraph 2. of this Appendix, A;

t0is the time at the beginning of the considered period j, s;

tendis the time at the end of the considered period j, s.

iis the index number of the considered REESS;

nis the total amount of REESS;

jis the index number for the considered period, where a period shall be any applicable cycle phase, combination of cycle phases and the applicable total cycle;

1

3600

is the conversion factor from Ws to Wh.

4.2.

For correction of CO2 mass emission, g/km, combustion process-specific Willans factors from Table A6.App2/3 shall be used.

4.3.

The correction shall be performed and applied for the total cycle and for each of its cycle phases separately, and shall be included in all relevant test reports.

4.4.

For this specific calculation, a fixed electric power supply system alternator efficiency shall be used:

ηalternator = 0,67 for electric power supply system REESS alternators

4.5.

The resulting CO2 mass emission difference for the considered period j due to load behaviour of the alternator for charging a REESS shall be calculated using the following equation:

ΔMCO2,j0,0036ΔEREESS,j 1ηalternator Willansfactor 1dj

where:

ΔMCO2,jis the resulting CO2 mass emission difference of period j, g/km;

ΔEREESS,jis the REESS energy change of the considered period j calculated in accordance with paragraph 4.1. of this Appendix, Wh;

djis the driven distance of the considered period j, km;

jis the index number for the considered period, where a period shall be any applicable cycle phase, combination of cycle phases and the applicable total cycle;

0,0036is the conversion factor from Wh to MJ;

ηalternatoris the efficiency of the alternator in accordance with paragraph 4.4. of this Appendix;

Willansfactoris the combustion process-specific Willans factor as defined in Table A6.App2/3, gCO2/MJ;

4.5.1.

The CO2 values of each phase and the total cycle shall be corrected as follows:

MCO2,p,3 = MCO2,p,1 – ΔMCO2,j

MCO2,c,3 = MCO2,c,2 – ΔMCO2,j

where:

ΔMCO2,jis the result from paragraph 4.5. of this Appendix for a period j, g/km.

4.6.

For the correction of CO2 emission, g/km, the Willans factors in Table A6.App2/3 shall be used.

Naturally aspirated | Pressure-charged

Positive ignition | | | |

Petrol (E10) | l/MJ | 0,0756 | 0,0803

gCO2/MJ | 174 | 184

CNG (G20) | m3/MJ | 0,0719 | 0,0764

gCO2/MJ | 129 | 137

LPG | l/MJ | 0,0950 | 0,101

gCO2/MJ | 155 | 164

E85 | l/MJ | 0,102 | 0,108

gCO2/MJ | 169 | 179

Compression ignition | | | |

Diesel (B7) | l/MJ | 0,0611 | 0,0611

gCO2/MJ | 161 | 161

  1. 1 Jan 2019 – 1 Sep 2023earlier wording
  2. 27 Jul 2017 – 1 Jan 2019earlier wording
  3. 1 Jun 2017 – 27 Jul 2017earlier wording