1.1.
The Type 1 test is used to verify the emissions of gaseous compounds, particulate matter, particle number, CO2 mass emission, fuel consumption, electric energy consumption and electric ranges over the applicable WLTP test cycle.
1.1.1.
The tests shall be carried out in accordance with the method described in paragraph 2. of this Sub-Annex or paragraph 3. of Sub-Annex 8 for pure electric, hybrid electric and compressed hydrogen fuel cell hybrid vehicles. Exhaust gases, particulate matter and particle number shall be sampled and analysed by the prescribed methods.
1.2.
The number of tests shall be determined in accordance with the flowchart in Figure A6/1. The limit value is the maximum allowed value for the respective criteria emission as specified in Table 2 of Annex I of Regulation (EC) No 715/2007.
1.2.1.
The flowchart in Figure A6/1 shall be applicable only to the whole applicable WLTP test cycle and not to single phases.
1.2.2.
The test results shall be the values after the target speed, REESS energy change-based, Ki, ATCT and Deterioration Factor corrections are applied.
1.2.3.1.
If during any of the tests a criteria emissions limit is exceeded, the vehicle shall be rejected.
1.2.3.2.
Depending on the vehicle type, the manufacturer shall declare as applicable the total cycle value of the CO2 mass emission, the electric energy consumption, fuel consumption for NOVC-FCHV as well as PER and AER in accordance with Table A6/1.
1.2.3.3.
The declared value of the electric energy consumption for OVC-HEVs under charge-depleting operating condition shall not be determined in accordance with Figure A6/1. It shall be taken as the type approval value if the declared CO2 value is accepted as the approval value. If that is not the case, the measured value of electric energy consumption shall be taken as the type approval value.
1.2.3.4.
If after the first test all criteria in row 1 of the applicable Table A6/2 are fulfilled, all values declared by the manufacturer shall be accepted as the type approval value. If any one of the criteria in row 1 of the applicable Table A6/2 is not fulfilled, a second test shall be performed with the same vehicle.
1.2.3.5.
After the second test, the arithmetic average results of the two tests shall be calculated. If all criteria in row 2 of the applicable Table A6/2 are fulfilled by these arithmetic average results, all values declared by the manufacturer shall be accepted as the type approval value. If any one of the criteria in row 2 of the applicable Table A6/2 is not fulfilled, a third test shall be performed with the same vehicle.
1.2.3.6.
After the third test, the arithmetic average results of the three tests shall be calculated. For all parameters which fulfil the corresponding criterion in row 3 of the applicable Table A6/2, the declared value shall be taken as the type approval value. For any parameter which does not fulfil the corresponding criterion in row 3 of the applicable Table A6/2, the arithmetic average result shall be taken as the type approval value.
1.2.3.7.
In the case that any one of the criterion of the applicable Table A6/2 is not fulfilled after the first or second test, at the request of the manufacturer and with the approval of the approval authority, the values may be re-declared as higher values for emissions or consumption, or as lower values for electric ranges, in order to reduce the required number of tests for type approval.
1.2.3.8.1.
Additional to the requirement of paragraph 1.2.3.8.2., the following values for dCO21, dCO22 and dCO23 shall be used in relation to the criteria for the number of tests in Table A6/2:
dCO21 = 0,990
dCO22 = 0,995
dCO23 = 1,000
1.2.3.8.2.
If the charge depleting Type 1 test for OVC-HEVs consists of two or more applicable WLTP test cycles and the dCO2x value is below 1,0, the dCO2x value shall be replaced by 1,0.
1.2.3.9.
In the case that a test result or an average of test results was taken and confirmed as the type approval value, this result shall be referred to as the ‘declared value’ for further calculations.
[The declared value shall be the value to which the necessary corrections are applied (i.e. Ki, ATCT and DF corrections] [Rounding xxx,xx] [Rounding xxx,x]
Vehicle type |
MCO2
(g/km)
FC
(kg/100 km)
Electric energy consumption
(Wh/km)
All electric range/Pure Electric Range
(km)
Vehicles tested in accordance with Sub-Annex 6 (pure ICE) |
MCO2
Paragraph 3. of Sub-Annex 7.
| — | —
NOVC-FCHV | — |
FCCS
Paragraph 4.2.1.2.1. of Sub-Annex 8.
| —
NOVC-HEV |
MCO2,CS
Paragraph 4.1.1. of Sub-Annex 8.
| — | —
OVC-HEV | CD |
MCO2,CD
Paragraph 4.1.2. of.
|
ECAC,CD
Paragraph 4.3.1. of Sub-Annex 8.
AER
Paragraph 4.4.1.1. of Sub-Annex 8.
CS |
MCO2,CS Sub-Annex 8
Paragraph 4.1.1. of Sub-Annex 8.
| — | —
PEV | — | — |
ECWLTC
Paragraph 4.3.4.2. of Sub-Annex 8.
PERWLTC
Paragraph 4.4.2. of Sub-Annex 8.
[Each test result shall fulfil the regulation limit.]
Test | Judgement parameter | Criteria emission | MCO2
Row 1 | First test | First test results | ≤ Regulation limit × 0,9 | ≤ Declared value × dCO21
Row 2 | Second test | Arithmetic average of the first and second test results | ≤ Regulation limit × 1,0 | ≤ Declared value × dCO22
Row 3 | Third test | Arithmetic average of three test results | ≤ Regulation limit × 1,0 | ≤ Declared value × dCO23
[‘0,9’ shall be replaced by ‘1,0’ for charge-depleting Type 1 test for OVC-HEVs, only if the charge-depleting test contains two or more applicable WLTC cycles.] [Each test result shall fulfil the regulation limit.]
Test | Judgement parameter | Criteria emissions | MCO2,CD | AER
Row 1 | First test | First test results | ≤ Regulation limit × 0,9 | ≤ Declared value × dCO21 | ≥ Declared value × 1,0
Row 2 | Second test | Arithmetic average of the first and second test results | ≤ Regulation limit × 1,0 | ≤ Declared value × dCO22 | ≥ Declared value × 1,0
Row 3 | Third test | Arithmetic average of three test results | ≤ Regulation limit × 1,0 | ≤ Declared value × dCO23 | ≥ Declared value × 1,0
Test | Judgement parameter | Electric energy consumption | PER
Row 1 | First test | First test results | ≤ Declared value × 1,0 | ≥ Declared value × 1,0
Row 2 | Second test | Arithmetic average of the first and second test results | ≤ Declared value × 1,0 | ≥ Declared value × 1,0
Row 3 | Third test | Arithmetic average of three test results | ≤ Declared value × 1,0 | ≥ Declared value × 1,0
Test | Judgement parameter | FCCS
Row 1 | First test | First test results | ≤ Declared value × 1,0
Row 2 | Second test | Arithmetic average of the first and second test results | ≤ Declared value × 1,0
Row 3 | Third test | Arithmetic average of three test results | ≤ Declared value × 1,0
1.2.4.1.1.
After the total cycle declared value of the CO2 mass emission is accepted, the arithmetic average of the phase-specific values of the test results in g/km shall be multiplied by the adjustment factor CO2_AF to compensate for the difference between the declared value and the test results. This corrected value shall be the type approval value for CO2.
CO2_AFDeclared valuePhase combined value
where:
Phase combined value
CO2aveL DL CO2aveM DM CO2aveH DH CO2aveexH DexH
DL DM DH DexH
where:
CO2aveLis the arithmetic average CO2 mass emission result for the L phase test result(s), g/km;
CO2aveMis the arithmetic average CO2 mass emission result for the M phase test result(s), g/km;
CO2aveHis the arithmetic average CO2 mass emission result for the H phase test result(s), g/km;
CO2aveexHis the arithmetic average CO2 mass emission result for the exH phase test result(s), g/km;
DLis theoretical distance of phase L, km;
DMis theoretical distance of phase M, km;
DHis theoretical distance of phase H, km;
DexHis theoretical distance of phase exH, km.
1.2.4.1.2.
If the total cycle declared value of the CO2 mass emission is not accepted, the type approval phase-specific CO2 mass emission value shall be calculated by taking the arithmetic average of the all test results for the respective phase.
The fuel consumption value shall be calculated by the phase-specific CO2 mass emission using the equations in paragraph 1.2.4.1. of this Sub-Annex and the arithmetic average of the emissions.
The phase-specific electric energy consumption and the phase-specific electric ranges are calculated by taking the arithmetic average of the phase specific values of the test result(s), without an adjustment factor.
2.1.1.
The Type 1 test shall consist of prescribed sequences of dynamometer preparation, fuelling, soaking, and operating conditions.
2.1.2.
The Type 1 test shall consist of vehicle operation on a chassis dynamometer on the applicable WLTC for the interpolation family. A proportional part of the diluted exhaust emissions shall be collected continuously for subsequent analysis using a constant volume sampler.
2.1.3.
Background concentrations shall be measured for all compounds for which dilute mass emissions measurements are conducted. For exhaust emissions testing, this requires sampling and analysis of the dilution air.
2.1.3.1.1.
Where the manufacturer requests subtraction of either dilution air or dilution tunnel background particulate mass from emissions measurements, these background levels shall be determined in accordance with the procedures listed in paragraphs 2.1.3.1.1.1. to 2.1.3.1.1.3. of this Sub-Annex.
2.1.3.1.1.1.
The maximum permissible background correction shall be a mass on the filter equivalent to 1 mg/km at the flow rate of the test.
2.1.3.1.1.2.
If the background exceeds this level, the default figure of 1 mg/km shall be subtracted.
2.1.3.1.1.3.
Where subtraction of the background contribution gives a negative result, the background level shall be considered to be zero.
2.1.3.1.2.
Dilution air background particulate mass level shall be determined by passing filtered dilution air through the particulate background filter. This shall be drawn from a point immediately downstream of the dilution air filters. Background levels in μg/m3 shall be determined as a rolling arithmetic average of at least 14 measurements with at least one measurement per week.
2.1.3.1.3.
Dilution tunnel background particulate mass level shall be determined by passing filtered dilution air through the particulate background filter. This shall be drawn from the same point as the particulate matter sample. Where secondary dilution is used for the test, the secondary dilution system shall be active for the purposes of background measurement. One measurement may be performed on the day of test, either prior to or after the test.
2.1.3.2.1.
Where the manufacturer requests a background correction, these background levels shall be determined as follows:
2.1.3.2.1.1. The background value may be either calculated or measured. The maximum permissible background correction shall be related to the maximum allowable leak rate of the particle number measurement system (0,5 particles per cm3) scaled from the particle concentration reduction factor, PCRF, and the CVS flow rate used in the actual test;
2.1.3.2.1.2. Either the approval authority or the manufacturer may request that actual background measurements are used instead of calculated ones.
2.1.3.2.1.3. Where subtraction of the background contribution gives a negative result, the PN result shall be considered to be zero.
2.1.3.2.2.
The dilution air background particle number level shall be determined by sampling filtered dilution air. This shall be drawn from a point immediately downstream of the dilution air filters into the PN measurement system. Background levels in particles per cm3 shall be determined as a rolling arithmetic average of least 14 measurements with at least one measurement per week.
2.1.3.2.3.
The dilution tunnel background particle number level shall be determined by sampling filtered dilution air. This shall be drawn from the same point as the PN sample. Where secondary dilution is used for the test the secondary dilution system shall be active for the purposes of background measurement. One measurement may be performed on the day of test, either prior to or after the test using the actual PCRF and the CVS flow rate utilised during the test.
2.2.1.1.
The following temperatures shall be measured with an accuracy of ± 1,5 °C:
Test cell ambient air;
Dilution and sampling system temperatures as required for emissions measurement systems defined in Sub-Annex 5.
2.2.1.2.
Atmospheric pressure shall be measurable with a precision of ± 0,1 kPa.
2.2.1.3.
Specific humidity H shall be measurable with a precision of ± 1 g H2O/kg dry air.
2.2.2.1.1.
The test cell shall have a temperature set point of 23 °C. The tolerance of the actual value shall be within ± 5 °C. The air temperature and humidity shall be measured at the test cell's cooling fan outlet at a minimum frequency of 0,1 Hz. For the temperature at the start of the test, see paragraph 2.8.1. of this Sub-Annex.
2.2.2.1.2.
The specific humidity H of either the air in the test cell or the intake air of the engine shall be such that:
5,5 ≤ H ≤ 12,2 (g H2O/kg dry air)
2.2.2.1.3.
Humidity shall be measured continuously at a minimum frequency of 0,1 Hz.
The soak area shall have a temperature set point of 23 °C and the tolerance of the actual value shall be within ± 3 °C on a 5-minute running arithmetic average and shall not show a systematic deviation from the set point. The temperature shall be measured continuously at a minimum frequency of 0,033 Hz (every 30 s).
The test vehicle shall conform in all its components with the production series, or, if the vehicle is different from the production series, a full description shall be included in all relevant test reports. In selecting the test vehicle, the manufacturer and the approval authority shall agree which vehicle model is representative for the interpolation family.
For the measurement of emissions, the road load as determined with test vehicle H shall be applied. In the case of a road load matrix family, for the measurement of emissions, the road load as calculated for vehicle HM in accordance with paragraph 5.1. of Sub-Annex 4 shall be applied.
If at the request of the manufacturer the interpolation method is used (see paragraph 3.2.3.2. of Sub-Annex 7), an additional measurement of emissions shall be performed with the road load as determined with test vehicle L. Tests on vehicles H and L should be performed with the same test vehicle and shall be tested with the shortest n/v ratio (with a tolerance of ± 1,5 per cent) within the interpolation family. In the case of a road load matrix family, an additional measurement of emissions shall be performed with the road load as calculated for vehicle LM in accordance with paragraph 5.1. of Sub-Annex 4.
Road load coefficients and the test mass of test vehicle L and H may be taken from different road load families, as long as the difference between these road load families results from applying paragraph 6.8. of Sub-Annex 4, and the requirements in paragraph 2.3.2. of this Sub-Annex are maintained.
2.3.2.1.
The interpolation method shall only be used if:
The difference in CO2 over the applicable cycle resulting from step 9 of Table A7/1 of Sub-Annex 7 between test vehicles L and H is between a minimum of 5 g/km and a maximum defined in paragraph 2.3.2.2.;
for all applicable phase values the CO2 values resulting of step 9 of Table A7/1 of Sub-Annex 7 of vehicle H are higher than those of vehicle L.
If these requirements are not met, tests can be declared void and repeated in agreement with the approval authority.
2.3.2.2.
The maximum delta CO2 allowed over the applicable cycle resulting from step 9 of Table A7/1 of Sub-Annex 7 between test vehicles L and H is 20 per cent plus 5 g/km of the CO2 emissions from vehicle H, but at least 15 g/km and not exceeding 30 g/km.
This restriction does not apply for the application of a road load matrix family.
2.3.2.3.
At the request of the manufacturer and with approval of the approval authority, the interpolation line may be extrapolated to a maximum of 3 g/km above the CO2 emission of vehicle H and/or below the CO2 emission of vehicle L. This extension is valid only within the absolute boundaries of the interpolation range specified in paragraph 2.3.2.2.
For the application of a road load matrix family, extrapolation is not permitted.
When two or more interpolation families are identical regarding the requirements of paragraph 5.6. of this Annex, but are distinct because their overall range for CO2 would be higher than the maximum delta specified in paragraph 2.3.2.2., then all individual vehicles of identical specification (e.g. make, model, optional equipment) shall belong to only one of the interpolation families.
The vehicle shall be presented in good technical condition. It shall have been run-in and driven between 3000 and 15000 km before the test. The engine, transmission and vehicle shall be run-in in accordance with the manufacturer's recommendations.
2.4.1.
Dynamometer settings and verification shall be performed in accordance with Sub-Annex 4.
2.4.2.1.
Auxiliary devices shall be switched off or deactivated during dynamometer operation unless their operation is required by legislation.
2.4.2.2.
The vehicle's dynamometer operation mode, if any, shall be activated by using the manufacturer's instruction (e.g. using vehicle steering wheel buttons in a special sequence, using the manufacturer's workshop tester, removing a fuse).
The manufacturer shall provide the approval authority a list of the deactivated devices and justification for the deactivation. The dynamometer operation mode shall be approved by the approval authority and the use of a dynamometer operation mode shall be included in all relevant test reports.
2.4.2.3.
The vehicle's dynamometer operation mode shall not activate, modulate, delay or deactivate the operation of any part that affects the emissions and fuel consumption under the test conditions. Any device that affects the operation on a chassis dynamometer shall be set to ensure a proper operation.
2.4.2.4.1.
If the test vehicle has two powered axles, and under WLTP conditions it is partially or permanently operated with two axles being powered or recuperating energy over the applicable cycle the vehicle shall be tested on a dynamometer in 4WD operation which fulfils the specifications in paragraphs 2.2. and 2.3. of Sub-Annex 5.
2.4.2.4.2.
If the test vehicle is tested with only one powered axle, the test vehicle shall be tested on a dynamometer in 2WD operation which fulfils the specifications in paragraph 2.2. of Sub-Annex 5.
At the request of the manufacturer and with the approval of the approval authority a vehicle with one powered axle may be tested on a 4WD dynamometer in 4WD operation mode.
2.4.2.4.3.
If the test vehicle is operated with two axles being powered in dedicated driver-selectable modes which are not intended for normal daily operation but only for special limited purposes, such as ‘mountain mode’ or ‘maintenance mode’, or when the mode with two powered axles is only activated in an off-road situation, the vehicle shall be tested on a dynamometer in 2WD operation which fulfils the specifications in paragraph 2.2. of Sub-Annex 5.
2.4.2.4.4.
If the test vehicle is tested on a 4WD dynamometer in 2WD operation the wheels on the non-powered axle may rotate during the test, provided that the vehicle dynamometer operation mode and vehicle coastdown mode support this way of operation.
2.4.2.5.1.
At the request of the manufacturer and with the approval of the approval authority, the vehicle which has to be tested on a dynamometer in 4WD operation may alternatively be tested on a dynamometer in 2WD operation if the following conditions are met:
the test vehicle is converted to have only one powered axle;
the manufacturer demonstrates to the approval authority that the CO2, fuel consumption and/or electrical energy consumption of the converted vehicle is the same or higher as for the non-converted vehicle being tested on a dynamometer in 4WD operation;
a safe operation is ensured for the test (e.g. by removing a fuse or dismounting a drive shaft) and an instruction is provided together with the dynamometer operation mode;
the conversion is only applied to the vehicle tested at the chassis dynamometer, the road load determination procedure shall be applied to the unconverted test vehicle.
2.4.2.5.2.
This demonstration of equivalency shall apply to all vehicles in the same road load family. At the request of the manufacturer, and with approval of the approval authority, this demonstration of equivalency may be extended to other road load families upon evidence that a vehicle from the worst-case road load family was selected as the test vehicle.
2.4.2.6.
Information on whether the vehicle was tested on a 2WD dynamometer or a 4WD dynamometer and whether it was tested on a dynamometer in 2WD operation or 4WD operation shall be included in all relevant test reports. In the case that the vehicle was tested on a 4WD dynamometer, with that dynamometer in 2WD operation, this information shall also indicate whether or not the wheels on the non-powered wheels were rotating.
2.4.3.
The vehicle's exhaust system shall not exhibit any leak likely to reduce the quantity of gas collected.
2.4.4.
The settings of the powertrain and vehicle controls shall be those prescribed by the manufacturer for series production.
2.4.5.
Tyres shall be of a type specified as original equipment by the vehicle manufacturer. Tyre pressure may be increased by up to 50 per cent above the pressure specified in paragraph 4.2.2.3. of Sub-Annex 4. The same tyre pressure shall be used for the setting of the dynamometer and for all subsequent testing. The tyre pressure used shall be included in all relevant test reports.
The appropriate reference fuel as specified in Annex IX shall be used for testing.
2.4.7.1.
The vehicle shall be approximately horizontal during the test so as to avoid any abnormal distribution of the fuel.
2.4.7.2.
If necessary, the manufacturer shall provide additional fittings and adapters, as required to accommodate a fuel drain at the lowest point possible in the tank(s) as installed on the vehicle, and to provide for exhaust sample collection.
2.4.7.3.