This Sub-Annex describes the determination of the road load of a test vehicle and the transfer of that road load to a chassis dynamometer.
2.2.
Reference speed points shall start at 20 km/h in incremental steps of 10 km/h and with the highest reference speed according to the following provisions:
The highest reference speed point shall be 130 km/h or the reference speed point immediately above the maximum speed of the applicable test cycle if this value is less than 130 km/h. In the case that the applicable test cycle contains less than the 4 cycle phases (Low, Medium, High and Extra High) and at the request of the manufacturer and with approval of the approval authority, the highest reference speed may be increased to the reference speed point immediately above the maximum speed of the next higher phase, but no higher than 130 km/h; in this case road load determination and chassis dynamometer setting shall be done with the same reference speed points;
If a reference speed point applicable for the cycle plus 14 km/h is more than or equal to the maximum vehicle speed vmax, this reference speed point shall be excluded from the coastdown test and from chassis dynamometer setting. The next lower reference speed point shall become the highest reference speed point for the vehicle.
2.3.
Unless otherwise specified, a cycle energy demand shall be calculated according to paragraph 5. of Sub-Annex 7 over the target speed trace of the applicable drive cycle.
2.4.
f0, f1, f2 are the road load coefficients of the road load equation F = f0 + f1 × v + f2 × v2 determined in accordance with this Sub-Annex.
f0is the constant road load coefficient and shall be rounded to one place of decimal, N;
f1is the first order road load coefficient and shall be rounded to three places of decimal, N/(km/h);
f2is the second order road load coefficient and shall be rounded to five places of decimal, N/(km/h)2.
Unless otherwise stated, the road load coefficients shall be calculated with a least square regression analysis over the range of the reference speed points.
mr is the equivalent effective mass of all the wheels and vehicle components rotating with the wheels on the road while the gearbox is placed in neutral, in kilograms (kg). mr shall be measured or calculated using an appropriate technique agreed upon by the approval authority. Alternatively, mr may be estimated to be 3 per cent of the sum of the mass in running order and 25 kg.
Coastdown times shall be transferred to forces and vice versa by taking into account the applicable test mass plus mr. This shall apply to measurements on the road as well as on a chassis dynamometer.
If the vehicle is tested on a dynamometer in 4WD operation, the equivalent inertia mass of the chassis dynamometer shall be set to the applicable test mass.
Otherwise, the equivalent inertia mass of the chassis dynamometer shall be set to the test mass plus either the equivalent effective mass of the wheels not influencing the measurement results or 50 per cent of mr.
2.6.
Additional masses for setting the test mass shall be applied such that the weight distribution of that vehicle is approximately the same as that of the vehicle with its mass in running order. In the case of category N vehicles or passenger vehicles derived from category N vehicles, the additional masses shall be located in a representative manner and shall be justified to the approval authority upon their request. The weight distribution of the vehicle shall be included in all relevant test reports and shall be used for any subsequent road load determination testing.
The manufacturer shall be responsible for the accuracy of the road load coefficients and shall ensure this for each production vehicle within the road load family. Tolerances within the road load determination, simulation and calculation methods shall not be used to underestimate the road load of production vehicles. At the request of the approval authority, the accuracy of the road load coefficients of an individual vehicle shall be demonstrated.
The required overall measurement accuracy shall be as follows:
Vehicle speed accuracy: ± 0,2 km/h with a measurement frequency of at least 10 Hz;
Time: min. accuracy: ± 10 ms; min. precision and resolution:10 ms;
Wheel torque accuracy: ± 6 Nm or ± 0,5 per cent of the maximum measured total torque, whichever is greater, for the whole vehicle, with a measurement frequency of at least 10 Hz;
Wind speed accuracy: ± 0,3 m/s, with a measurement frequency of at least 1 Hz;
Wind direction accuracy: ± 3°, with a measurement frequency of at least 1 Hz;
Atmospheric temperature accuracy: ± 1 °C, with a measurement frequency of at least 0,1 Hz;
Atmospheric pressure accuracy: ± 0,3 kPa, with a measurement frequency of at least 0,1 Hz;
Vehicle mass measured on the same weighing scale before and after the test: ± 10 kg (± 20 kg for vehicles > 4000 kg);
Tyre pressure accuracy: ± 5 kPa;
Wheel rotational speed accuracy: ± 0,05 s– 1 or 1 per cent, whichever is greater.
The wind velocity during a measurement shall remain within ± 2 km/h at the centre of the test section. The possible wind velocity shall be at least 140 km/h.
The air temperature during a measurement shall remain within ± 3 °C at the centre of the test section. The air temperature distribution at the nozzle outlet shall remain within ± 3 °C.
For an equally-spaced 3 by 3 grid over the entire nozzle outlet, the turbulence intensity, Tu, shall not exceed 1 per cent. See Figure A4/1.
Tuu′U∞
where:
Tuis the turbulence intensity;
u′is the turbulent velocity fluctuation, m/s;
U∞is the free flow velocity, m/s.
The vehicle blockage ratio εsb expressed as the quotient of the vehicle frontal area and the area of the nozzle outlet as calculated using the following equation, shall not exceed 0,35.
εsbAfAnozzle
where:
εsbis the vehicle blockage ratio;
Afis the frontal area of the vehicle, m2;
Anozzleis the nozzle outlet area, m2.
To properly determine the aerodynamic influence of the wheels, the wheels of the test vehicle shall rotate at such a speed that the resulting vehicle velocity is within ± 3 km/h of the wind velocity.
To simulate the fluid flow at the underbody of the test vehicle, the wind tunnel shall have a moving belt extending from the front to the rear of the vehicle. The speed of the moving belt shall be within ± 3 km/h of the wind velocity.
At nine equally distributed points over the nozzle area, the root mean square deviation of both the pitch angle α and the yaw angle β (Y-, Z-plane) at the nozzle outlet shall not exceed 1°.
At nine equally distributed points over the nozzle outlet area, the standard deviation of the total pressure at the nozzle outlet shall be equal to or less than 0.02.
σ ΔPtq0,02
where:
σis the standard deviation of the pressure ratio ΔPtq;
ΔPtis the variation of total pressure between the measurement points, N/m2;
qis the dynamic pressure, N/ m2.
The absolute difference of the pressure coefficient cp over a distance 3 metres ahead and 3 metres behind the centre of the balance in the empty test section and at a height of the centre of the nozzle outlet shall not deviate more than ± 0,02.
cpx 3m cpx 3m0,02
where:
cpis the pressure coefficient.
At x = 0 (balance center point), the wind velocity shall have at least 99 per cent of the inflow velocity 30 mm above the wind tunnel floor.
δ99 x 0m30mm
where:
δ99is the distance perpendicular to the road, where 99 per cent of free stream velocity is reached (boundary layer thickness).
The restraint system mounting shall not be in front of the vehicle. The relative blockage ratio of the vehicle frontal area due to the restraint system, εrestr, shall not exceed 0,10.
εrestrArestrAf
where:
εrestris the relative blockage ratio of the restraint system;
Arestris the frontal area of the restraint system projected on the nozzle face, m2;
Afis the frontal area of the vehicle, m2.
The inaccuracy of the resulting force in the x-direction shall not exceed ± 5 N. The resolution of the measured force shall be within ± 3 N.
The precision of the measured force shall be within ± 3 N.
The maximum permissible wind conditions for road load determination are described in paragraphs 4.1.1.1.1. and 4.1.1.1.2.
In order to determine the applicability of the type of anemometry to be used, the arithmetic average of the wind speed shall be determined by continuous wind speed measurement, using a recognized meteorological instrument, at a location and height above the road level alongside the test road where the most representative wind conditions will be experienced.
If tests in opposite directions cannot be performed at the same part of the test track (e.g. on an oval test track with an obligatory driving direction), wind speed and direction at each part of the test track shall be measured. In this case the higher measured arithmetic average wind speed determines the type of anemometry to be used and the lower arithmetic average wind speed the criterion for the allowance of waiving of a wind correction.
Stationary anemometry shall be used only when wind speeds over a period of 5 seconds average less than 5 m/s and peak wind speeds are less than 8 m/s for less than 2 seconds. In addition, the average vector component of the wind speed across the test road shall be less than 2 m/s during each valid run pair. Run pairs that do not meet the above criteria shall be excluded from the analysis. Any wind correction shall be calculated as given in paragraph 4.5.3. Wind correction may be waived when the lowest arithmetic average wind speed is 2 m/s or less.
For testing with an on-board anemometer, a device as described in paragraph 4.3.2. shall be used. The arithmetic average of the wind speed during each valid run pair over the test road shall be less than 7 m/s with peak wind speeds of less than 10 m/s for more than 2 seconds. In addition, the average vector component of the wind speed across the road shall be less than 4 m/s during each valid run pair. Run pairs that do not meet the above criteria shall be excluded from the analysis.
The atmospheric temperature should be within the range of 5 °C up to and including 35 °C.
If the difference between the highest and the lowest measured temperature during the coastdown test is more than 5 °C, the temperature correction shall be applied separately for each run with the arithmetic average of the ambient temperature of that run.
In that case the values of the road load coefficients f0, f1 and f2 shall be determined and corrected for each individual run. The final set of f0, f1 and f2 values shall be the arithmetic average of the individually corrected coefficients f0, f1 and f2 respectively.
At its option, a manufacturer may choose to perform coastdowns between 1 °C and 5 °C.
The road surface shall be flat, even, clean, dry and free of obstacles or wind barriers that might impede the measurement of the road load, and its texture and composition shall be representative of current urban and highway road surfaces. The longitudinal slope of the test road shall not exceed ± 1 per cent. The local slope between any points 3 metres apart shall not deviate more than ± 0,5 per cent from this longitudinal slope. If tests in opposite directions cannot be performed at the same part of the test track (e.g. on an oval test track with an obligatory driving direction), the sum of the longitudinal slopes of the parallel test track segments shall be between 0 and an upward slope of 0,1 per cent. The maximum camber of the test road shall be 1,5 per cent.
Each test vehicle shall conform in all its components with the production series, or, if the vehicle is different from the production vehicle, a full description shall be included in all relevant test reports.
A test vehicle (vehicle H) with the combination of road load relevant characteristics (i.e. mass, aerodynamic drag and tyre rolling resistance) producing the highest cycle energy demand shall be selected from the family (see paragraphs 5.6. and 5.7. of this Annex).
If the aerodynamic influence of the different wheels within one interpolation family is not known, the selection shall be based on the highest expected aerodynamic drag. As a guideline, the highest aerodynamic drag may be expected for wheels with (a) the largest width, (b) the largest diameter, and (c) the most open structure design (in that order of importance).
The wheel selection shall be performed additional to the requirement of the highest cycle energy demand.
At the request of the manufacturer, an interpolation method may be applied.
In this case, two test vehicles shall be selected from the family complying with the respective family requirement.
Test vehicle H shall be the vehicle producing the higher, and preferably highest, cycle energy demand of that selection, test vehicle L the one producing the lower, and preferably lowest, cycle energy demand of that selection.
All items of optional equipment and/or body shapes that are chosen not to be considered when applying the interpolation method shall be identical for both test vehicles H and L such that these items of optional equipment produce the highest combination of the cycle energy demand due to their road load relevant characteristics (i.e. mass, aerodynamic drag and tyre rolling resistance).
In the case where individual vehicles may be supplied with a complete set of standard wheels and tyres and a complete set of snow tyres (marked with 3 Peaked Mountain and Snowflake – 3PMS) with or without wheels, the additional wheels/tyres shall not be considered as optional equipment.
As a guidance, the following minimum deltas between vehicles H and L should be fulfilled for that road load relevant characteristic:
mass at least 30 kg;
rolling resistance at least 1,0 kg/t;
aerodynamic drag CD × A at least 0,05 m2.
To achieve a sufficient delta between vehicle H and L on a particular road load relevant characteristic, the manufacturer may artificially worsen vehicle H, e.g. by applying a higher test mass.
For the criteria defining an interpolation family, see paragraph 5.6. of this Annex.
4.2.1.2.2.
Requirements for applying the interpolation family using the interpolation method are:
Fulfilling the interpolation family criteria listed in paragraph 5.6. of this Annex;
Fulfilling the requirements in paragraphs 2.3.1. and 2.3.2. of Sub-Annex 6;
Performing the calculations in paragraph 3.2.3.2. of Sub-Annex 7.
4.2.1.2.3.1.
At the request of the manufacturer and upon fulfilling the criteria of paragraph 5.7. of this Annex, the road load values for vehicles H and L of an interpolation family shall be calculated.
4.2.1.2.3.2.
Test vehicles H and L as defined in paragraph 4.2.1.1.2. shall be referred to as HR and LR for the purpose of the road load family.
4.2.1.2.3.3.
In addition to the requirements of an interpolation family in paragraphs 2.3.1. and 2.3.2. of Sub-Annex 6, the difference in cycle energy demand between HR and LR of the road load family shall be at least 4 per cent and shall not exceed 35 per cent based on HR over a complete WLTC Class 3 cycle.
If more than one transmission is included in the road load family, a transmission with the highest power losses shall be used for road load determination.
4.2.1.2.3.4.
If the road load delta of the vehicle option causing the friction difference is determined in accordance with paragraph 6.8., a new road load family shall be calculated which includes the road load delta in both vehicle L and vehicle H of that new road load family.
f0,N = f0,R + f0,Delta
f1,N = f1,R + f1,Delta
f2,N = f2,R + f2,Delta
where:
Nrefers to the road load coefficients of the new road load family;
Rrefers to the road load coefficients of the reference road load family;
Deltarefers to the delta road load coefficients determined in paragraph 6.8.1.
Table A4/1 shows the permissible combinations of test vehicle selection and family requirements as described in paragraphs 4.2.1.1. and 4.2.1.2.
Requirements to be fulfilled: |
w/o interpolation method
Interpolation method w/o road load family
Applying the road load family
Interpolation method using one or more road load families
Road load test vehicle | Paragraph 4.2.1.1.1. | Paragraph 4.2.1.1.2. | Paragraph 4.2.1.1.2. | n.a.
Family | Paragraph 4.2.1.2.1. | Paragraph 4.2.1.2.2. | Paragraph 4.2.1.2.3. | Paragraph 4.2.1.2.2.
Additional | none | none | none | Application of column (3) ‘Applying the road load family’ and application of paragraph 4.2.1.3.1.
Road loads HR and/or LR shall be determined in accordance with this Sub-Annex.
The road load of vehicle H (and L) of an interpolation family within the road load family shall be calculated in accordance with paragraphs 3.2.3.2.2. to 3.2.3.2.2.4. of Sub-Annex 7 by:
Using HR and LR of the road load family instead of H and L as inputs for the equations;
Using the road load parameters (i.e. test mass, Δ(CD × Af) compared to vehicle LR, and tyre rolling resistance) of vehicle H (or L) of the interpolation family as inputs for the individual vehicle;
Repeating this calculation for each H and L vehicle of every interpolation family within the road load family.
The road load interpolation shall only be applied on those road load-relevant characteristics that were identified to be different between test vehicle LR and HR. For other road load-relevant characteristic(s), the value of vehicle HR shall apply.
H and L of the interpolation family may be derived from different road load families. If that difference between these road load families comes from applying the delta method, refer to paragraph 4.2.1.2.3.4.
4.2.1.3.2. For the purposes of paragraph 4.2.1.3. of this Sub-Annex, vehicle H of a road load family shall be designated vehicle HR. All references to vehicle H in paragraph 4.2.1. of this Sub-Annex shall be replaced by vehicle HR and all references to an interpolation family in paragraph 4.2.1. of this Sub-Annex shall be replaced by road load family.
4.2.1.3.3. For the purposes of paragraph 4.2.1.3. of this Sub-Annex, vehicle L of a road load family shall be designated vehicle LR. All references to vehicle L in paragraph 4.2.1. of this Sub-Annex shall be replaced by vehicle LR and all references to an interpolation family in paragraph 4.2.1. of this Sub-Annex shall be replaced by road load family.
4.2.1.3.4. Notwithstanding the requirements referring to the range of an interpolation family in paragraphs 1.2.3.1. and 1.2.3.2. of Sub-Annex 6, the difference in cycle energy demand between HR and LR of the road load family shall be at least 4 per cent and shall not exceed 35 per cent based on HR over a complete WLTC Class 3 cycle.
If more than one transmission is included in the road load family, a transmission with the highest power losses shall be used for road load determination.
4.2.1.3.5. Road loads HR and/or LR shall be determined according to this Sub-Annex.
The road load of vehicles H (and L) of an interpolation family within the road load family shall be calculated according to paragraphs 3.2.3.2.2. to 3.2.3.2.2.4. inclusive of Sub-Annex 7, by:
using HR and LR of the road load family instead of H and L as inputs for the equations;
using the road load parameters (i.e. test mass, Δ(CD × Af) compared to vehicle LR, and tyre rolling resistance) of vehicle H (or L) of the interpolation family as inputs for the "individual vehicle";
repeating this calculation for each H and L vehicle of every interpolation family within the road load family.
The road load interpolation shall only be applied on those road load relevant characteristics that were identified to be different between test vehicle LR and HR. For other road load relevant characteristic(s), the value of vehicle HR shall apply.
A vehicle that fulfils the criteria of paragraph 5.8. of this Annex that is:
representative of the intended series of complete vehicles to be covered by the road load matrix family in terms of estimated worst CD value and body shape, and
representative of the intended series of vehicles to be covered by the road load matrix family in terms of estimated average of the mass of optional equipment, shall be used to determine the road load.
In the case that no representative body shape for a complete vehicle can be determined, the test vehicle shall be equipped with a square box with rounded corners with radii of maximum of 25 mm and a width equal to the maximum width of the vehicles covered by the road load matrix family, and a total height of the test vehicle of 3,0 m ± 0,1 m, including the box.
The manufacturer and the approval authority shall agree which vehicle test model is representative.
The vehicle parameters test mass, tyre rolling resistance and frontal area of both a vehicle HM and LM shall be determined in such a way that vehicle HM produces the highest cycle energy demand and vehicle LM the lowest cycle energy from the road load matrix family. The manufacturer and the approval authority shall agree on the vehicle parameters for vehicle HM and LM.
The road load of all individual vehicles of the road load matrix family, including HM and LM, shall be calculated according to paragraph 5.1. of this Sub-Annex.
Movable aerodynamic body parts on the test vehicles shall operate during road load determination as intended under WLTP Type 1 test conditions (test temperature, vehicle speed and acceleration range, engine load, etc.).
Every vehicle system that dynamically modifies the vehicle’s aerodynamic drag (e.g. vehicle height control) shall be considered to be a movable aerodynamic body part. Appropriate requirements shall be added if future vehicles are equipped with movable aerodynamic items of optional equipment whose influence on aerodynamic drag justifies the need for further requirements.
Before and after the road load determination procedure, the selected vehicle shall be weighed, including the test driver and equipment, to determine the arithmetic average mass, mav. The mass of the vehicle shall be greater than or equal to the test mass of vehicle H or of vehicle L at the start of the road load determination procedure.
The test vehicle configuration shall be included in all relevant test reports and shall be used for any subsequent coastdown testing.
The test vehicle shall be suitably run-in for the purpose of the subsequent test for at least 10000 but no more than 80000 km.