1.1.
The shifting procedures described in this Sub-Annex shall apply to vehicles equipped with manual shift transmissions.
1.2.
The prescribed gears and shifting points are based on the balance between the power required to overcome driving resistance and acceleration, and the power provided by the engine in all possible gears at a specific cycle phase.
1.3.
The calculation to determine the gears to use shall be based on engine speeds and full load power curves versus engine speed.
1.4.
For vehicles equipped with a dual-range transmission (low and high), only the range designed for normal on-road operation shall be considered for gear use determination.
1.5.
The prescriptions for the clutch operation shall not be applied if the clutch is operated automatically without the need of an engagement or disengagement of the driver.
1.6.
This Sub-Annex shall not apply to vehicles tested in accordance with Sub-Annex 8.
The following data are required and calculations shall be performed in order to determine the gears to be used when driving the cycle on a chassis dynamometer:
Prated, the maximum rated engine power as declared by the manufacturer, kW;
nrated, the rated engine speed declared by the manufacturer as the engine speed at which the engine develops its maximum power, min– 1;
nidle, idling speed, min–1.
nidle shall be measured over a period of at least 1 minute at a sampling rate of at least 1 Hz with the engine running in warm condition, the gear lever placed in neutral, and the clutch engaged. The conditions for temperature, peripheral and auxiliary devices, etc. shall be the same as described in Sub-Annex 6 for the Type 1 test.
The value to be used in this Sub-Annex shall be the arithmetic average over the measuring period, rounded or truncated to the nearest 10 min–1;
ng, the number of forward gears.
The forward gears in the transmission range designed for normal on-road operation shall be numbered in descending order of the ratio between engine speed in min– 1 and vehicle speed in km/h. Gear 1 is the gear with the highest ratio, gear ng is the gear with the lowest ratio. ng determines the number of forward gears;
(n/v)i, the ratio obtained by dividing the engine speed n by the vehicle speed v for each gear i, for i to ngmax, min– 1/(km/h). (n/v)i shall be calculated using the equations in paragraph 8. of Sub-Annex 7;
f0, f1, f2, road load coefficients selected for testing, N, N/(km/h), and N/(km/h)2 respectively;
nmax
nmax1 = n95_high, the maximum engine speed where 95 per cent of rated power is reached, min– 1;
If n95_high cannot be determined because the engine speed is limited to a lower value nlim for all gears and the corresponding full load power is higher than 95 per cent of rated power, n95_high shall be set to nlim.
nmax2 = (n/v)(ngmax) × vmax,cycle
nmax3 = (n/v)(ngmax) × vmax,vehicle
where:
ngvmaxis defined in paragraph 2.(i);
vmax,cycleis the maximum speed of the vehicle speed trace in accordance with Sub-Annex 1, km/h;
vmax,vehicleis the maximum speed of the vehicle in accordance with paragraph 2.(i), km/h;
(n/v)(ngvmax)is the ratio obtained by dividing engine speed n by the vehicle speed v for the gear ngvmax, min– 1/(km/h);
nmaxis the maximum of nmax1, nmax2 and nmax3, min–1.
Pwot(n), the full load power curve over the engine speed range
The power curve shall consist of a sufficient number of data sets (n, Pwot) so that the calculation of interim points between consecutive data sets can be performed by linear interpolation. Deviation of the linear interpolation from the full load power curve in accordance with Annex XX shall not exceed 2 per cent. The first data set shall be at nmin_drive_set (see point (k)(3)) or lower. The last data set shall be at nmax or higher engine speed. Data sets need not be spaced equally but all data sets shall be reported.
The data sets and the values Prated and nrated shall be taken from the power curve as declared by the manufacturer.
The full load power at engine speeds not covered by Annex XX shall be determined in accordance with the method described in Annex XX;
Determination of ngvmax and vmax
ngvmax, the gear in which the maximum vehicle speed is reached and shall be determined as follows:
If vmax(ng) ≥ vmax(ng – 1) and vmax(ng – 1) ≥ vmax(ng – 2), then:
ngvmax = ng and vmax = vmax(ng).
If vmax(ng) < vmax(ng – 1) and vmax(ng – 1) ≥ vmax(ng – 2), then:
ngvmax = ng – 1 and vmax = vmax(ng – 1),
otherwise, ngvmax = ng -2 and vmax = vmax(ng – 2)
where:
vmax(ng)is the vehicle speed at which the required road load power equals the available power Pwot in gear ng (see Figure A2/1a).
vmax(ng – 1)is the vehicle speed at which the required road load power equals the available power Pwot in the next lower gear (gear ng – 1). See Figure A2/1b.
vmax(ng – 2)is the vehicle speed at which the required road load power equals the available power Pwot in the gear ng – 2.
Vehicle speed values rounded to one place of decimal shall be used for the determination of vmax and ngvmax.
The required road load power, kW, shall be calculated using the following equation:
Prequiredf0vf1v2f2v3
3600
where:
vis the vehicle speed specified above, km/h.
The available power at vehicle speed vmax in gear ng, gear ng – 1 or gear ng – 2 may be determined from the full load power curve, Pwot(n), by using the following equations:
nng = (n/v)ng × vmax(ng);
nng – 1 = (n/v)ng – 1 × vmax(ng – 1);
nng – 2 = (n/v)ng – 2 × vmax(ng – 2),
and by reducing the power values of the full load power curve by 10 per cent.
The method described above shall be extended to even lower gears, i.e. ng – 3, ng – 4, etc. if necessary.
If, for the purpose of limiting maximum vehicle speed, the maximum engine speed is limited to nlim which is lower than the engine speed corresponding to the intersection of the road load power curve and the available power curve, then:
ngvmax = ngmax and vmax = nlim / (n/v)(ngmax).
Exclusion of a crawler gear
Gear 1 may be excluded at the request of the manufacturer if all of the following conditions are fulfilled:
The vehicle family is homologated to tow a trailer;
(n/v)1 × (vmax / n95_high) > 6,74;
(n/v)2 × (vmax / n95_high) > 3,85;
The vehicle, having a mass mt as defined in the equation below, is able to pull away from standstill within 4 seconds, on an uphill gradient of at least 12 per cent, on five separate occasions within a period of 5 minutes.
mt = mr0 + 25 kg + (MC – mr0 – 25 kg) × 0,28
(factor 0,28 in the above equation shall be used for category N vehicles with a gross vehicle mass up to 3,5 tonnes and shall be replaced by factor 0,15 in the case of category M vehicles),
where:
vmaxis the maximum vehicle speed as specified in paragraph 2. (i). Only the vmax value resulting from the intersection of the required road load power curve and the available power curve of the relevant gear shall be used for the conditions in (3) and (4) above. A vmax value resulting from a limitation of the engine speed which prevents this intersection of curves shall not be used;
(n/v)(ngvmax)is the ratio obtained by dividing the engine speed n by the vehicle speed v for gear ngvmax, min– 1/(km/h);
mr0is the mass in running order, kg;
MCis the gross train mass (gross vehicle mass + max. trailer mass), kg.
In this case, gear 1 shall not be used when driving the cycle on a chassis dynamometer and the gears shall be renumbered starting with the second gear as gear 1.
Definition of nmin_drive
nmin_drive is the minimum engine speed when the vehicle is in motion, min–1;
For ngear = 1, nmin_drive = nidle,
For ngear = 2,
for transitions from first to second gear:
nmin_drive = 1,15 × nidle,
for decelerations to standstill:
nmin_drive = nidle.
for all other driving conditions:
nmin_drive = 0,9 × nidle.
For ngear > 2, nmin_drive shall be determined by:
nmin_drive = nidle + 0,125 ×( nrated – nidle ).
This value shall be referred to as nmin_drive_set.
The final results for nmin_drive shall be rounded to the nearest integer. Example: 1199,5 becomes 1200, 1199,4 becomes 1199.
Values higher than nmin_drive_set may be used for ngear > 2 if requested by the manufacturer. In this case, the manufacturer may specify one value for acceleration/constant speed phases (nmin_drive_up) and a different value for deceleration phases (nmin_drive_down).
Samples which have acceleration values ≥ – 0,1389 m/s2 shall belong to the acceleration/constant speed phases.
In addition, for an initial period of time (tstart_phase), the manufacturer may specify higher values (nmin_drive_start and/or nmin_drive_up_start) for the values nmin_drive and/or nmin_drive_up for ngear > 2 than specified above.
The initial time period shall be specified by the manufacturer but shall not exceed the low speed phase of the cycle and shall end in a stop phase so that there is no change of nmin_drive within a short trip.
All individually chosen nmin_drive values shall be equal to or higher than nmin_drive_set but shall not exceed (2 × nmin_drive_set).
All individually chosen nmin_drive values and tstart_phase shall be included in all relevant test reports.
Only nmin_drive_set shall be used as the lower limit for the full load power curve in accordance with paragraph 2(h).
TM, test mass of the vehicle, kg.
For each second j of the cycle trace, the power required to overcome driving resistance and to accelerate shall be calculated using the following equation:
Prequired,jf0 vj f1 v2j f2 v3j
3600
kraj vj TM
3600
where:
Prequired,jis the required power at second j, kW;
aj
is the vehicle acceleration at second j, m/s2, and is calculated as follows:
aj
vj1vj
3,6tj1tj;
kris a factor taking the inertial resistances of the drivetrain during acceleration into account and is set to 1,03.
For any vj < 1 km/h, it shall be assumed that the vehicle is standing still and the engine speed shall be set to nidle. The gear lever shall be placed in neutral with the clutch engaged except 1 second before beginning an acceleration from standstill where first gear shall be selected with the clutch disengaged.
For each vj ≥ 1 km/h of the cycle trace and each gear i, i = 1 to ngmax, the engine speed, ni,j, shall be calculated using the following equation:
ni,j = (n/v)i × vj
The calculation shall be performed with floating point numbers, the results shall not be rounded.
The following gears may be selected for driving the speed trace at vj:
All gears i < ngvmax where nmin_drive ≤ ni,j ≤ nmax1;
All gears i ≥ ngvmax where nmin_drive ≤ ni,j ≤ nmax2;
Gear 1, if n1,j < nmin_drive.
If aj < 0 and ni,j ≤ nidle, ni,j shall be set to nidle and the clutch shall be disengaged.
If aj ≥ 0 and ni,j < max(1,15 × nidle; min. engine speed of the Pwot(n) curve), ni,j shall be set to the maximum of 1,15 × nidle or (n/v)i × vj and the clutch shall be set to ‘undefined’.
‘undefined’ covers any status of the clutch between disengaged and engaged, depending on the individual engine and transmission design. In this case the real engine speed may deviate from the calculated engine speed.
The available power for each possible gear i and each vehicle speed value of the cycle trace vi shall be calculated using the following equation:
Pavailable_i,j = Pwot (ni,j) × (1 – (SM + ASM))
where:
Pratedis the rated power, kW;
Pwotis the power available at ni,j at full load condition from the full load power curve;
SMis a safety margin accounting for the difference between the stationary full load condition power curve and the power available during transition conditions. SM is set to 10 per cent;
ASMis an additional power safety margin which may be applied at the request of the manufacturer.
When requested, the manufacturer shall provide the ASM values (in per cent reduction of the wot power) together with data sets for Pwot(n) as shown by the example in Table A2/1. Linear interpolation shall be used between consecutive data points. ASM is limited to 50 per cent.
The application of an ASM requires the approval of the approval authority.
n | Pwot | SM per cent | ASM per cent | Pavailable
min–1 | kW | kW
700 | 6,3 | 10,0 | 20,0 | 4,4
1000 | 15,7 | 10,0 | 20,0 | 11,0
1500 | 32,3 | 10,0 | 15,0 | 24,2
1800 | 56,6 | 10,0 | 10,0 | 45,3
1900 | 59,7 | 10,0 | 5,0 | 50,8
2000 | 62,9 | 10,0 | 0,0 | 56,6
3000 | 94,3 | 10,0 | 0,0 | 84,9
4000 | 125,7 | 10,0 | 0,0 | 113,2
5000 | 157,2 | 10,0 | 0,0 | 141,5
5700 | 179,2 | 10,0 | 0,0 | 161,3
5800 | 180,1 | 10,0 | 0,0 | 162,1
6000 | 174,7 | 10,0 | 0,0 | 157,3
6200 | 169,0 | 10,0 | 0,0 | 152,1
6400 | 164,3 | 10,0 | 0,0 | 147,8
6600 | 156,4 | 10,0 | 0,0 | 140,8
The possible gears to be used shall be determined by the following conditions:
The conditions of paragraph 3.3. are fulfilled, and
For ngear > 2, if Pavailable_i,j ≥ Prequired,j.
The initial gear to be used for each second j of the cycle trace is the highest final possible gear, imax. When starting from standstill, only the first gear shall be used.
The lowest final possible gear is imin.
The initial gear selection shall be checked and modified in order to avoid too frequent gearshifts and to ensure driveability and practicality.
An acceleration phase is a time period of more than 2 seconds with a vehicle speed ≥ 1 km/h and with monotonic increase of vehicle speed. A deceleration phase is a time period of more than 2 seconds with a vehicle speed ≥ 1 km/h and with monotonic decrease of vehicle speed.
Corrections and/or modifications shall be made in accordance with the following requirements:
If a one step higher gear (n + 1) is required for only 1 second and the gears before and after are the same (n) or one of them is one step lower (n – 1), gear (n + 1) shall be corrected to gear n.
Gear sequence i – 1, i, i – 1 shall be replaced by:
i – 1, i – 1, i – 1;
Gear sequence i – 1, i, i – 2 shall be replaced by:
i – 1, i – 1, i – 2;
Gear sequence i – 2, i, i – 1 shall be replaced by:
i – 2, i – 1, i – 1.
Gears used during accelerations at vehicle speeds ≥ 1 km/h shall be used for a period of at least 2 seconds (e.g. a gear sequence 1, 2, 3, 3, 3, 3, 3 shall be replaced by 1, 1, 2, 2, 3, 3, 3). This requirement shall not be applied on downshifts during an acceleration phase. Such downshifts shall be corrected in accordance with paragraph 4(b). Gears shall not be skipped during acceleration phases.
However an upshift by two gears is permitted at the transition from an acceleration phase to a constant speed phase if the duration of the constant speed phase exceeds 5 seconds.
If a downshift is required during an acceleration phase the gear which is required during this downshift is noted (iDS). The start point of a correction procedure is defined by either the last previous second when iDS was identified, or the start point of the acceleration phase if all time samples before have gears > iDS. The following check shall then be applied.
Working backwards from the end of the acceleration phase, the latest occurrence of a 10 second window containing iDS for either 2 or more consecutive seconds, or 2 or more individual seconds shall be identified. The last usage of iDS in this window defines the end point of the correction procedure. Between the start and end of the correction period, all requirements for gears greater than iDS shall be corrected to a requirement of iDS.
From the end of the correction period to the end of the acceleration phase, all downshifts with a duration of only one second shall be removed, if the downshift was a one step downshift. If the downshift was a two step downshift, all requirements for gears greater than or equal to iDS up to the latest occurrence of iDS shall be corrected to (iDS + 1).
This final correction shall also be applied from the start point to the end of the acceleration phase, if no 10 second window containing iDS for either 2 or more consecutive seconds or 2 or more individual seconds was identified.
If the initially calculated gear use is:
2, 2, 3, [3, 4, 4, 4, 4, 3, 4, 4, 4, 4], 4, 4, 3, 4, 4, 4,
the gear use shall be corrected to:
2, 2, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 4, 4, 4.
If the initially calculated gear use is:
2, 2, 3, [3, 4, 4, 3, 4, 4, 4, 4, 4, 4], 4, 4, 4, 4, 3, 4,
the gear use shall be corrected to:
2, 2, 3, 3, 3, 3, 3, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4.
If the initially calculated gear use is:
2, 2, 3, [3, 4, 4, 4, 4, 4, 4, 4, 4, 4], 4, 4, 4, 3, 3, 4,
the gear use shall be corrected to:
2, 2, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 4.
The first 10 second windows are indicated by square brackets in the examples above.
The underlined gears (e.g. 3) indicate those cases which could lead to a correction of the gear before it.
This correction shall not be performed for gear 1.
If gear i is used for a time sequence of 1 to 5 seconds and the gear prior to this sequence is one step lower and the gear after this sequence is one or two steps lower than within this sequence or the gear prior to this sequence is two steps lower and the gear after this sequence is one step lower than within the sequence, the gear for the sequence shall be corrected to the maximum of the gears before and after the sequence.
Gear sequence i – 1, i, i – 1 shall be replaced by:
i – 1, i – 1, i – 1;
Gear sequence i – 1, i, i – 2 shall be replaced by:
i – 1, i – 1, i – 2;
Gear sequence i – 2, i, i – 1 shall be replaced by:
i – 2, i – 1, i – 1.
Gear sequence i – 1, i, i, i – 1 shall be replaced by:
i – 1, i – 1, i – 1, i – 1;
Gear sequence i – 1, i, i, i – 2 shall be replaced by:
i – 1, i – 1, i – 1, i – 2;
Gear sequence i – 2, i, i, i – 1 shall be replaced by:
i – 2, i – 1, i – 1, i – 1.
Gear sequence i – 1, i, i, i, i – 1 shall be replaced by:
i – 1, i – 1, i – 1, i – 1, i – 1;
Gear sequence i – 1, i, i, i, i – 2 shall be replaced by:
i – 1, i – 1, i – 1, i – 1, i – 2;
Gear sequence i – 2, i, i, i, i – 1 shall be replaced by:
i – 2, i – 1, i – 1, i – 1, i – 1.
Gear sequence i – 1, i, i, i, i, i – 1 shall be replaced by:
i – 1, i – 1, i – 1, i – 1, i – 1, i – 1;
Gear sequence i – 1, i, i, i, i, i – 2 shall be replaced by:
i – 1, i – 1, i – 1, i – 1, i – 1, i – 2;
Gear sequence i – 2, i, i, i, i, i – 1 shall be replaced by:
i – 2, i – 1, i – 1, i – 1, i – 1, i – 1.
Gear sequence i – 1, i, i, i, i, i, i – 1 shall be replaced by:
i – 1, i – 1, i – 1, i – 1, i – 1, i – 1, i – 1.
Gear sequence i – 1, i, i, i, i, i, i – 2 shall be replaced by:
i – 1, i – 1, i – 1, i – 1, i – 1, i – 1, i – 2;
Gear sequence i – 2, i, i, i, i, i, i – 1 shall be replaced by:
i – 2, i – 1, i – 1, i – 1, i – 1, i – 1, i – 1.
In all cases (i) to (v), i – 1 ≥ imin shall be fulfilled.
No upshift to a higher gear at the transition from an acceleration or constant speed phase to a deceleration phase shall be performed if the gear in the phase following the deceleration phase is lower than the upshifted gear.
If vi ≤ vi + 1 and vi + 2 < vi + 1 and gear i = 4 and gear (i + 1 = 5) and gear (i + 2 = 5), then gear (i + 1) and gear (i + 2) shall be set to 4 if the gear for the phase following the deceleration phase is gear 4 or lower. For all following cycle trace points with gear 5 within the deceleration phase, the gear shall also be set to 4. If the gear following the deceleration phase is gear 5, an upshift shall be performed.
If there is an upshift during the transition and the initial deceleration phase by 2 gears, an upshift by 1 gear shall be performed.
No upshift to a higher gear shall be performed within a deceleration phase.
During a deceleration phase, gears with ngear > 2 shall be used as long as the engine speed does not drop below nmin_drive.
Gear 2 shall be used during a deceleration phase within a short trip of the cycle (not at the end of a short trip) as long as the engine speed does not drop below (0,9 × nidle).
If the engine speed drops below nidle, the clutch shall be disengaged.
If the deceleration phase is the last part of a short trip shortly before a stop phase, the second gear shall be used as long as the engine speed does not drop below nidle.
If during a deceleration phase the duration of a gear sequence between two gear sequences of 3 seconds or more is only 1 second, it shall be replaced by gear 0 and the clutch shall be disengaged.
If during a deceleration phase the duration of a gear sequence between two gear sequences of 3 seconds or more is 2 seconds, it shall be replaced by gear 0 for the 1st second and for the 2nd second with the gear that follows after the 2 second period. The clutch shall be disengaged for the 1st second.
Example: A gear sequence 5, 4, 4, 2 shall be replaced by 5, 0, 2, 2.
This requirement shall only be applied if the gear that follows after the 2 second period is > 0.
If several gear sequences with durations of 1 or 2 seconds follow one another, corrections shall be performed as follows:
A gear sequence i, i, i, i – 1, i – 1, i – 2 or i, i, i, i – 1, i – 2, i – 2 shall be changed to i, i, i, 0, i – 2, i – 2.
A gear sequence such as i, i, i, i – 1, i – 2, i – 3 or i, i, i, i – 2, i – 2, i – 3 or other possible combinations shall be changed to i, i, i, 0, i – 3, i – 3.
This change shall also be applied to gear sequences where the acceleration is ≥ 0 for the first 2 seconds and < 0 for the 3rd second or where the acceleration is ≥ 0 for the last 2 seconds.
For extreme transmission designs, it is possible that gear sequences with durations of 1 or 2 seconds following one another may last up to 7 seconds. In such cases, the correction above shall be complemented by the following correction requirements in a second step:
A gear sequence j, 0, i, i, i – 1, k with j > (i + 1) and k ≤ (i – 1) shall be changed to j, 0, i – 1, i – 1, i – 1, k, if gear (i – 1) is one or two steps below imax for second 3 of this sequence (one after gear 0).
If gear (i – 1) is more than two steps below imax for second 3 of this sequence, a gear sequence j, 0, i, i, i – 1, k with j > (i + 1) and k ≤ (i – 1) shall be changed to j, 0, 0, k, k, k.