Annex Number | Annex title
I | List of applicable UNECE regulations
II | Requirements on vehicle structure integrity
III | Requirements on the maximum design speed, speed governors and speed limitation devices
IV | Requirements on steering for fast tractors
V | Requirements on steering
VI | Requirements on speedometers
VII | Requirements on the field of vision and windscreen wipers
VIII | Requirements on glazing
IX | Requirements on rear-view mirrors
X | Requirements on driver information systems
XI | Requirements on lighting, light-signalling devices and their light sources
XII | Requirements on lighting installations
XIII | Requirements on vehicle occupant protection, including interior fittings, head restraints, seat belts, vehicle doors
XIV | Requirements on vehicle exterior and accessories
XV | Requirements on the electromagnetic compatibility
XVI | Requirements on audible warning devices
XVII | Requirements on heating systems
XVIII | Requirements on devices to prevent unauthorised use
XIX | Requirements on registration plates
XX | Requirements on statutory plates and markings
XXI | Requirements on dimensions and trailer masses
XXII | Requirements on the maximum laden mass
XXIII | Requirements on ballast masses
XXIV | Requirements on the safety of electrical systems
XXV | Requirements on fuel tanks
XXVI | Requirements on rear protective structures
XXVII | Requirements on lateral protection
XXVIII | Requirements on load platforms
XXIX | Requirements on towing devices
XXX | Requirements on tyres
XXXI | Requirements on spray-suppression systems
XXXII | Requirements on the reverse gear
XXXIII | Requirements on tracks
XXXIV | Requirements on mechanical couplings
[UN Regulation No 148 may be used as an alternative to UN Regulations Nos 4, 6, 7, 23, 38, 50, 77, 87 and 91.] [UN Regulation No 149 may be used as an alternative to UN Regulations Nos 19, 98, 112, 113, 119 and 123.] [UN Regulation No 150 may be used as an alternative to UN Regulations Nos 3, 27, 69, 70 and 104.]
Regulation Number | Subject | Series of amendments | OJ Reference | Applicability
1 | Lighting installation | Incorporating all valid text up to 02 series of amendments | OJ L 177, 10.7.2010, p. 1 | T and C
3 | Lighting, light-signalling devices and their light sources | Supplement 12 to the 02 series of amendments | OJ L 323, 6.12.2011, p. 1 | T, C, R and S
4 | Lighting, light-signalling devices and their light sources |
Supplement 14 to the original version of the Regulation
Supplement 15 to the original version of the Regulation
OJ L 31, 31.1.2009, p. 35
OJ L 4, 7.1.2012, p. 17
T, C, R and S
5 | Lighting, light-signalling devices and their light sources | Incorporating all valid text up to 03 series of amendments | OJ L 162, 29.5.2014, p. 1 | T and C
6 | Lighting, light-signalling devices and their light sources |
Supplement 19 to the 01 series of amendments
Corrigendum 1 to Supplement 18
Supplement 19 to the 01 series of amendments
OJ L 177, 10.7.2010, p. 40 | T, C, R and S
6 | Lighting, light signalling devices and their light sources |
Supplement 18 to the 01 series of amendments
Corrigendum 1 to Supplement 18
Supplement 19 to the 01 series of amendments
OJ L 177, 10.7.2010, p. 40 | T, C, R and S
7 |
Lighting, light-signalling devices and their light sources
Lighting installation
Supplement 16 to the 02 series of amendments | OJ L 148, 12.6.2010, p. 1 | T, C, R and S
8 | Lighting installation |
Incorporating all valid text up to 05 series of amendments
Corrigendum 1 to Revision 4 of the Regulation
OJ L 177, 10.7.2010, p. 71 | T and C
10 | Electromagnetic compatibility |
04 series of amendments
Corrigendum 1 to the Revision 4
Supplement 1 to the 04 series of amendments
OJ L 254, 20.9.2012, p. 1 | T and C
18 | Devices to prevent unauthorised use | Supplement 2 to the 03 series of amendments | OJ L 120, 13.5.2010, p. 29 | T and C
19 | Lighting, light-signalling devices and their light sources | Supplement 2 to the 03 series of amendments | OJ L 177, 10.7.2010, p. 113 | T and C
20 | Lighting installation | Incorporating all valid text up to 03 series of amendments | OJ L 177, 10.7.2010, p. 170 | T and C
21 | Interior fittings – doors | Supplement 3 to the 01 series of amendments | OJ L 188, 16.7.2008, p. 32 | T and C
23 | Lighting, light-signalling devices and their light sources | Supplement 17 to the original version of the Regulation | OJ L 4, 17.1.2012, p. 18 | T, C, R and S
23 | Lighting, light signalling devices and their light sources | Supplement 17 to the original version of the Regulation | OJ L 4, 7.1.2012, p. 18 | T, C, R and S
25 | Head restraints |
04 series of amendments
Corrigendum 2 to Revision 1 of the Regulation
OJ L 215, 14.8.2010, p. 1 | T and C
28 | Audible warning devices | Supplement 3 to the original version of the Regulation | OJ L 323, 6.12.2011, p. 33 | T and C
30 | Tyres |
Supplement 15 to the 02 series of amendments
Supplement 16 to the 02 series of amendments
OJ L 201, 30.7.2008, p. 70
OJ L 307, 23.11.2011, p. 1
T, R and S
31 | Lighting, light-signalling devices and their light sources | Supplement 7 to the 02 series of amendments | OJ L 185, 17.7.2010, p. 15 | T and C
37 | Lighting, light-signalling devices and their light sources | Supplement 34 to the 03 series of amendments | OJ L 297, 13.11.2010, p. 1 | T, C and R
38 | Lighting, light-signalling devices and their light sources |
Supplement 15 to the original version of the Regulation
Corrigendum 1 to Supplement 12
Amendments to Regulation 38 incorporating Supplement 15 to the original version of the Regulation
OJ L 148, 12.6.2010, p. 55
OJ L 4, 7.1.2012, p. 20
T and C
43 | Glazing | Supplement 2 to the 01 series of amendments | OJ L 42, 12.02.2014, p. 1 | T and C
46 | Rear view mirrors |
Supplement 4 to the 02 series of amendments
Corrigendum 1 to supplement 4
OJ L 177, 10.7.2010, p. 211 | T and C
48 | Lighting installation |
Supplement 6 to the 04 series of amendments
05 series of amendments
OJ L 323, 6.12.2011, p. 46 | T, C, R and S
54 | Tyres |
Supplement 16 to the original version of the Regulation
Supplement 17 to the original version of the Regulation
OJ L 183, 11.7.2008, p. 41
OJ L 307, 23.11.2011, p. 2
T, R and S
55 | Mechanical couplings | Supplement 1 to the 01 series of amendments | OJ L 227, 28.8.2010, p. 1 | T, C, R and S
62 | Devices to prevent unauthorised use | Supplement 2 to the original version of the Regulation | OJ L 89, 27.3.2013, p. 37 | T and C
69 |
Lighting, light-signalling devices and their light sources
Lighting installation
Supplement 5 to the 01 series of amendments | OJ L 200, 31.7.2010, p. 1 |
T and C
T, C, R and S
73 | Lateral protection | 01 series of amendments | OJ L 122, 8.5.2012, p. 1 | R3b and R4B
75 | Tyres | Supplement 13 to the Regulation in its original form | OJ L 84, 30.3.2011, p. 46 | T, R and S
77 | Lighting installation | Supplement 14 to the original version of the Regulation | OJ L 4, 7.1.2012, p. 4 | T, C, R and S
77 | Lighting installation | Supplement 14 to the original version of the Regulation | OJ L 4, 7.1.2012, p. 21 | T, C, R and S
79 | Steering for fast tractors | Supplement 3 to the 01 series of amendments | OJ L 137, 27.5.2008, p. 25 | Tb and Cb
81 | Rear view mirrors | Supplement 2 to the original version of the Regulation | OJ L 185, 13.7.2012, p. 1 | T and C with straddle seat and handlebar
87 | Lighting, light-signalling devices and their light sources |
Supplement 14 to the original version of the Regulation
Correction 1 to Revision 2
Supplement 15 to the original version of the Regulation
OJ L 164, 30.6.2010, p. 46
OJ L 4, 7.1.2012, p. 24
T and C
89 | Maximum design speed, speed governors and speed limitation devices | Supplement 1 to the original version of the Regulation | OJ L 158, 19.6.2007, p. 1 | T and C
91 | Lighting, light-signalling devices and their light sources |
Supplement 11 to the original version of the Regulation
Supplement 12 to the original version of the Regulation
Supplement 13 to the original version of the Regulation
OJ L 164, 30.6.2010, p. 69
OJ L 4, 7.1.2012, p. 27
R and S
98 | Lighting, light-signalling devices and their light sources | Supplement 4 to the 01 series of amendments | OJ L 176, 14.6.2014, p. 64 | T and C
99 | Lighting, light-signalling devices and their light sources | Supplement 5 to the original version of the Regulation | OJ L 164, 30.6.2010, p. 151 | T and C
104 | Lighting installation | Amendments incorporating all valid text up to: Supplement 7 to the original version of the Regulation | OJ L 75, 14.3.2014, p. 29 | T, C, R and S
106 | Tyres | Supplement 8 to the original version of the Regulation | OJ L 257, 30.9.2010, p. 231 | T, R and S
112 | Lighting, light-signalling devices and their light sources | Supplement 12 to the original version of the Regulation | OJ L 230, 31.8.2010, p. 264 | T and C
113 | Lighting, light-signalling devices and their light sources | Amendments incorporating all valid text up to Supplement 3 to the 01 series of amendments to the Regulation | OJ L 176, 14.6.2014, p. 128 | T and C
117 | Tyres |
02 series of amendments
Corrigendum 1 to the 02 series of amendments
Corrigendum 2 to the 02 series of amendments
Corrigendum 3 to the 02 series of amendments
OJ L 307, 23.11.2011, p. 3 | T, R and S
119 | Lighting, light-signalling devices and their light sources | Amendments incorporating all valid text up to Supplement 3 to the 01 series of amendments | OJ L 89, 25.3.2014, p. 101 | T and C
122 | Heating systems |
Corrigendum 2 to the original version of the Regulation
Supplement 1 to the original version of the Regulation
OJ L 164, 30.6.2010, p. 231 | T and C
123 | Adaptive front lighting systems | Incorporating all valid text up to Supplement 4 to the original version of the Regulation | OJ L 222, 24.8.2010, p. 1 | T and C
128 | Light emitting diode (LED) light sources | Incorporating all valid text up to Supplement 2 to the original version of the Regulation | OJ L 162, 29.5.2014, p. 43 | T, C and R
148 | Light-signalling devices (LSD) | Original version of the Regulation | OJ L 347, 30.9.2021, p. 123, ELI: http://data.europa.eu/eli/reg/2021/1719/oj | T, C, R and S
149 | Road illumination devices (RID) | Original version of the Regulation | OJ L 347, 30.9.2021, p. 173, ELI: http://data.europa.eu/eli/reg/2021/1720/oj | T and C
150 | Retro-reflective devices (RRD) | Original version of the Regulation | OJ L 347, 30.9.2021, p. 297, ELI: http://data.europa.eu/eli/reg/2021/1721/oj | T, C, R and S
The transitional provisions of the UNECE regulations listed in this table apply, except where specific alternative dates are provided for in this Regulation. Compliance with prescriptions in accordance with subsequent amendments to those listed in this table shall also be accepted.
Vehicles shall be designed and constructed in order to be sufficiently robust to withstand their intended use over their normal lifetime, taking into account regular and scheduled maintenance and specific equipment adjustments clearly and unambiguously set out in the operator’s manual provided with the vehicle. The vehicle manufacturer shall provide a signed statement to this effect.
Vehicle assembly and construction in the assembly plants, in particular the processes relating to the vehicle frame, chassis and body and the drivetrain, shall be covered by a quality assurance system to ensure that essential mechanical connections, such as welds and threaded connections, as well as other relevant material characteristics, are checked and verified as appropriate.
The approval authority shall verify the quality assurance system as part of the conformity of production arrangements referred to in Article 28 of Regulation (EU) No 167/2013.
The type-approval authority shall verify that in the event of a recall due to a serious safety risk, specific analysis of vehicle structures, components and/or parts by means of engineering calculations, virtual testing methods and/or structural testing can upon request be made available without delay to the approval authority and the European Commission.
Vehicle type-approval shall not be granted if there is reason to doubt that the vehicle manufacturer is able to make available the analysis referred to in point 4. This doubt could relate either to the accessibility or the existence of such analysis (e.g. application for type-approval of a limited batch of vehicles from a non-established manufacturer represented by a party unlikely to have any meaningful access to such analysis).
For the purposes of this Annex:
1.1. ‘Speed governor’ means a device used to measure and regulate the speed of the engine and/or vehicle.
1.2. ‘Powertrain’ means a group of components that generate power and deliver it to the road surface, including the engine, transmission, drive shafts, differentials and drive wheels or tracks.
1.3. ‘Tampering’ means unauthorised modifications which may prejudice functional safety, in particular by increasing vehicle performance, and damage the environment.
1.4. ‘Speed limitation device’ means a device whose primary function is to control the fuel feed to the engine in order to limit the vehicle speed to the specified value.
2.1. For the type-approval tests, the average speed shall be measured on a straight track, which the tractor shall traverse in both directions from a flying start. The soil of the track shall be stabilised; the track shall be flat and at least 100 metres long; however, it may include slopes of not more than 1,5 %.
2.2. During the test, the tractor shall be unladen and in running order without ballast weights or special equipment and the tyre pressures shall be those specified for road use.
2.3. During the test the tractor shall be fitted with new pneumatic tyres having the greatest tyre rolling radius, expressed by the speed radius index, intended by the manufacturer for the tractor.
2.4. The gear ratio used during the test shall be that producing the maximum vehicle speed and the throttle shall be fully open.
2.5. In order to take account of various unavoidable errors due, in particular, to the measuring technique and to the increase in running speed of the engine with a partial load, a measured speed exceeding the value for the maximum design speed by 3 km/h shall be acceptable for the type-approval test. An additional 5 % tolerance shall be permitted in order to take into account variations due to tyre size.
2.6. In order for approval authorities may calculate their maximum theoretical speed, the manufacturer shall specify as a guide the gear ratio, the actual forward movement of the powered wheels corresponding to one complete revolution, and the rpm at maximum power output or the cut-off initiation speed under full load with the throttle fully open, whichever is higher, and the speed governor, if fitted, adjusted as laid down by the manufacturer. The maximum theoretical speed shall be calculated without the tolerances referred to in point 2.5.
3.1. If a speed governor is fitted as standard by the manufacturer, it shall be installed and designed in such a way that the tractor complies with point 2 the above provisions on maximum design speed.
Vehicles of categories T and C, with maximum design speed exceeding 60 km/h, shall be equipped with adjustable speed limitation devices that comply with the requirements set out in this Annex.
4.1.1. Adjustable speed limitation devices shall comply with the requirements for N2 and N3 vehicles set out in points 1 and 2, Part II point 13.2, Part III points 21.2 and 21.3, Annex 5 point 1 and Annex 6 to UNECE Regulation No 89, as referenced in Annex I.
The powertrain tampering prevention measures are aimed at ensuring that a vehicle which meets the environmental and propulsion performance requirements, the vehicle construction requirements as well as the functional safety requirements at type approval remains compliant over its useful life and that adverse changes to the vehicle’s powertrain which have negative impacts on functional safety and/or on the environment are discouraged.
4.3.1. The manufacturer shall ensure that the approval authority and technical service are provided with the necessary information and, where appropriate, the necessary vehicles, propulsion systems, components and separate technical units to enable them to verify that the requirements set out in this Annex have been met.
4.3.2. The manufacturer shall declare in the application for type approval its commitment not to market the interchangeable components which could involve an increase in the propulsion performance above that applicable to the relevant variant.
4.4.1. For vehicles equipped with (an) electrical/electronic device(s) which limit its propulsion performance, the vehicle manufacturer shall provide data and evidence to the technical services to demonstrate that modification or disconnection of the device or its wiring system will not increase the propulsion performance.
4.4.2. Any vehicle equipped with electronic control shall include features to prevent modification, except as permitted by the manufacturer. The manufacturer shall permit modifications if those modifications are necessary for the diagnosis, servicing, inspection, retrofitting or repair of the vehicle.
4.4.3. Any reprogrammable computer codes or operating parameter shall be resistant to tampering.
4.4.4. Computer-coded propulsion operating parameters shall not be changeable without the use of specialised tools and procedures, e.g. soldered or potted computer components, sealed or soldered computer enclosures.
4.4.5. Any removable calibration memory chips shall be potted, encased in a sealed container or protected by electronic algorithms and shall not be changeable without the use of specialised tools and procedures.
4.4.6. Manufacturers using programmable computer code systems (e.g. electrical erasable programmable read-only memory, EEPROM) shall deter unauthorised reprogramming. Manufacturers shall include enhanced tamper-protection strategies and write-protect features requiring electronic access to an off-site computer maintained by the manufacturer, to which independent operators shall also have adequately protected access.
4.4.7. Stored on-board diagnostic trouble codes in the powertrain or engine control unit(s), that is numeric or alphanumeric identifiers which identify or label a malfunction in them, shall not be erased by disconnection of the on board computer from the vehicle power supply or by disconnection or failure of the vehicle battery or ground.
The requirements set out in sections 2, 5 and 6 and in Annexes 4 and 6 to UNECE Regulation No 79, as referenced in Annex I, for the steering of motor vehicles apply to vehicles of categories Tb and Cb with maximum design speed exceeding 60 km/h.
1.1. The requirements of ISO 10998:2008, Amd 1 2014 apply to the steering of vehicles belonging to categories Tb and Cb with maximum design speed exceeding 40 km/h and not exceeding 60 km/h.
1.2. The steering action of Cb tractors is in accordance with point 3.9 of Annex XXXIII.
The requirements on steering effort for the vehicles referred to in point 1 shall be the same as the requirements for vehicles of N2 category set out in section 6 of UNECE Regulation No 79 as referenced in Annex I.
For a vehicle equipped with a straddle seat and handlebars, the same steering effort should apply at the middle of the grip.
The requirements of ISO 10998:2008, Amd 1 2014 shall apply to the steering of vehicles belonging to categories Tb and Cb with maximum design speed exceeding 40 km/h and not exceeding 60 km/h.
The steering action of Cb tractors shall be in accordance with the requirements laid down in point 3.9 of Annex XXXIII.
The requirements on steering effort for the vehicles referred to in points 1 shall be the same as the requirements for vehicles of N2 category set out in section 6 of UNECE Regulation No 79 as referenced in Annex I.
For a vehicle equipped with a straddle seat and handlebars, the same steering effort requirements shall apply at the middle of the grip.
For the purposes of this Annex, the definitions in section 1 of Annex XXXIII shall apply. The following definitions shall also apply:
1.1. ‘Steering equipment’ means all the equipment the purpose of which is to alter the direction of movement of the tractor.
The steering equipment may be considered to include the steering control, the steering gear, the steered wheels, and, where applicable, special equipment to produce additional or independent power.
1.2. ‘Steering gear’ means all the components between the steering control and the steered wheels, with the exception of the special equipment defined in point 1.3. The steering gear may be mechanical, hydraulic, pneumatic, electric or a combination of any of these.
1.3. ‘Special equipment’ means the part of the steering equipment by which additional or independent power is produced. Additional or independent power may be produced by any mechanical, hydraulic, pneumatic or electrical system, or by any combination of these (for example by an oil pump, air pump or battery, etc.).
1.4. ‘Assisted steering equipment’ means the equipment in which the power for the deflection of the steered wheels is provided both by the muscular power of the driver and by the special equipment; this includes steering equipment where the steering power is normally provided solely by the special equipment, but which in the event of failure of the special equipment enables the muscular power of the driver to be used for steering.
1.5. ‘Servo-steering equipment’ means the equipment in which the power for the deflection of the steered wheels is provided solely by the special equipment.
1.6. ‘Differential steering’ means a method of steering on wheels or on tracks where the orientation of the tractor is done by creating a different rotational speed between the left and the right hand wheels or track assemblies.
1.7. ‘Steered wheels’ means one of the following:
the wheels the alignment of which may be altered directly or indirectly in relation to that of the tractor in order to obtain a change in the direction of movement of the tractor,
all wheels of articulated tractors,
wheels on the same axle, the speed of which may be varied in order to obtain a change in the direction of movement of the tractor.
2.1. The steering equipment shall ensure easy and safe handling of the tractor and shall comply with the detailed requirements set out in point 3.
2.2. The steering action of C-category tractors is in accordance with the requirements set out in point 3.9 of Annex XXXIII.