1 SUMMARY, Commission Delegated Regulation (EU) No 1322/2014 of 19 September 2014 supplementing and…

In forcesince 26 Jun 2018

Annex Number | Annex title

Vehicle construction and general type-approval requirements

I | Application of UNECE regulations

II | Recognition of test reports issued on the basis of OECD Codes for the purposes of EU type-approval

III | Arrangements with regard to type-approval procedures, including the requirements relating to virtual testing

IV | Arrangements with regard to conformity of production

V | Requirements with regard to access to repair and maintenance information

VI | Requirements applying to roll-over protection structures (dynamic testing)

VII | Requirements applying to roll-over protection structures (track-laying tractors)

VIII | Requirements applying to roll-over protection structures (static testing)

IX | Requirements applying to roll-over protection structures (front mounted roll-over protective structures on narrow-track tractors)

X | Requirements applying to roll-over protection structures (rear mounted roll-over protective structures on narrow-track tractors)

XI | Requirements applying to falling objects protection structures

XII | Requirements applying to passenger seats

XIII | Requirements applying to the driver’s exposure to noise level

XIV | Requirements applying to the driving seat

XV | Requirements applying to operating space and to access to the driving position

XVI | Requirements applying to power take-offs

XVII | Requirements applying to the protection of drive components

XVIII | Requirements applying to seat-belt anchorages

XIX | Requirements applying to safety belts

XX | Requirements applying to the protection against penetrating objects

XXI | Requirements applying to exhaust systems

XXII | Requirements applying to the operator’s manual

XXIII | Requirements applying to control devices, including safety and reliability of control systems and emergency and automatic stop devices

XXIV | Requirements applying to the protection against other mechanical hazards

XXV | Requirements applying to guards and protective devices

XXVI | Requirements applying to information, warnings and markings

XXVII | Requirements applying to materials and products

XXVIII | Requirements applying to batteries

XXIX | Requirements applying to protection against hazardous substances

Requirements relating to technical services

XXX | Performance standards and assessment of technical services

UNECE regulation No | Subject | Series of amendments | OJ Reference | Applicability

14 | Safety-belt anchorages, ISOFIX anchorages systems and ISOFIX top tether anchorages | Supplement 1 to the 07 series of amendments | OJ L 109, 28.4.2011, p. 1 | T and C

16 | Safety belts, restraint systems and child restraint systems | Supplement 1 to the 06 series of amendments | OJ L 233, 9.9.2011, p. 1 | T and C

43 | Safety glazing | Supplement 12 to the 00 series of amendments | OJ L 230, 31.8.2010, p. 119 | T and C

60 | Driver operated controls — identification of controls, tell-tales and indicators (moped/motorcycles) | | OJ L 95, 31.3.2004, p. 10 | T and C

79 | Steering equipment | Supplement 3 to the 01 series of amendments and Corrigendum 20 January 2006 | OJ L 137, 27.5.2008, p. 25 | T and C

The fact that a component is included in this list does not make its installation mandatory. For certain components, however, mandatory installation requirements are laid down in other Annexes to this Regulation.

The transitional provisions of the UNECE regulations listed in this table shall apply, except where specific alternative dates are provided for in this Regulation. Compliance with prescriptions in accordance with subsequent amendments to those listed in this table shall also be accepted.

Test report on the basis of OECD standard Code No | Subject | Edition | Applicability | Alternative to the EU test report on the basis of

3 |

Official testing of protective structures on agricultural and forestry tractors

(dynamic test)

Edition 2017

-February 2017-

T1, T4.2 and T4.3 |

Annex VI

Annex XVIII (if the seat-belt anchorages have been tested)

4 |

Official testing of protective structures on agricultural and forestry tractors

(static test)

Edition 2017

-February 2017-

T1/C1, T4.2/C4.2 and T4.3/C4.3 |

Annex VIII and

Annex XVIII (if the seat-belt anchorages have been tested)

5 | Official measurement of noise at the driving position(s) on agricultural and forestry tractors |

Edition 2017

-February 2017-

T and C | Annex XIII

6 | Official testing of front mounted roll-over protective structures on narrow-track wheeled agricultural and forestry tractors |

Edition 2017

-February 2017-

T2/C2, T3/C3 and T4.3/C4.3 |

Annex IX (if the performance requirements for foldable roll-over protection structures have been tested and met) and

Annex XVIII (if the seat-belt anchorages have been tested)

7 | Official testing of rear mounted roll-over protective structure on narrow-track wheeled agricultural and forestry tractors |

Edition 2017

-February 2017-

T2/C2, T3/C3 and T4.3/C4.3 |

Annex X (if the performance requirements for foldable roll-over protection structures have been tested and met) and

Annex XVIII (if the seat-belt anchorages have been tested)

8 | Official testing of protective structures on agricultural and forestry track-laying tractors |

Edition 2017

-February 2017-

C1, C2, C4.2 and C4.3 |

Annex VII and

Annex XVIII (if the seat-belt anchorages have been tested)

10 | Official testing of falling object protective structures on agricultural and forestry tractors |

Edition 2017

-February 2017-

T and C |

Annex XI

Part C

When receiving an application for vehicle type-approval, the approval authority shall:

1.1. verify that all EU type-approval certificates issued and test reports granted pursuant to Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation which are applicable for vehicle type-approval cover the vehicle type and correspond to the prescribed requirements;

1.2. by reference to the documentation make sure that the vehicle specifications and data contained in the vehicle information document are included in the data in the information packages and in the EU type-approval certificates issued in accordance with Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation;

1.3. on a selected sample of vehicles from the type to be approved carry out or arrange to be carried out inspections of vehicle parts and systems to verify that the vehicle(s) is/are built in accordance with the relevant data contained in the authenticated information package in respect of Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation;

1.4. carry out or arrange to be carried out relevant installation checks in respect of separate technical units where applicable;

1.5. carry out or arrange to be carried out necessary checks in respect of the presence of the subjects provided for in Annex I of Regulation (EU) No 167/2013;

The number of vehicles to be submitted shall be sufficient to permit the proper check of the various combinations to be type-approved according to the following criteria:

2.1. propulsion unit;

2.2. transmission;

2.3. powered axles (number, position and interconnection);

2.4. steered axles (number and position);

2.5. braking system and braked axles (number);

2.6. roll-over protection structure;

2.7. protection against hazardous substances.

Where no approval certificates or test reports in respect of the subjects covered by Regulation (EU) No 167/2013 or the delegated and implementing acts adopted pursuant to that Regulation are available, the approval authority shall:

3.1. arrange for the necessary tests and checks as required by Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation;

3.2. verify that the vehicle conforms to the particulars in the vehicle information folder and that it meets the technical requirements of Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation;

3.3. carry out or arrange to be carried out relevant installation checks in respect of components and separate technical units where applicable.

4.1.1. The satisfactory operation of the process of multi-stage EU type-approval requires joint action by all the manufacturers concerned. To this end type-approval authorities shall ensure, before granting first and subsequent stage approval, that suitable arrangements exist between the relevant manufacturers for the supply and interchange of documents and information such that the completed vehicle type meets the technical requirements of Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation. Such information shall include details of relevant system, component and separate technical unit approvals and of vehicle parts which form part of the incomplete vehicle but are not yet approved.

4.1.2. EU Type-approvals in accordance with point 4 are granted on the basis of the current state of completion of the vehicle type and shall incorporate all approvals granted at earlier stages.

4.1.3. Each manufacturer in a multi-stage EU type-approval process is responsible for the approval and conformity of production of all systems, components or separate technical units manufactured by him or added by him to the previously built stage. He is not responsible for subjects which have been approved in an earlier stage except in those cases where he modifies relevant parts to an extent that the previously granted approval becomes invalid.

The approval authority shall:

4.2.1. verify that all EU type-approval certificates issued and test reports granted pursuant to Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation which are applicable for vehicle type-approval cover the vehicle type at its state of completion and correspond to the prescribed requirements;

4.2.2. ensure that all the relevant data, taking account of the state of completion of the vehicle, is included in the information folder;

4.2.3. by reference to the documentation make sure that the vehicle specification(s) and data contained in the vehicle information folder are included in the data in the information packages and in the EU type-approval certificates, in accordance with Regulation (EU) No 167/2013 or the delegated and implementing acts adopted pursuant to that Regulation; and in the case of a completed vehicle, where an item number in the information folder is not included in any of the information packages, confirm that the relevant part of characteristic conforms to the particulars in the information folder;

4.2.4. on a selected sample of vehicles from the type to be approved carry out or arrange to be carried out inspections of vehicle parts and systems to verify that the vehicle(s) is/are built in accordance with the relevant data contained in the authenticated information package in respect of Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation;

4.2.5. Carry out or arrange to be carried out relevant installation checks in respect of separate technical units where applicable.

4.3.

The number of vehicles to be inspected for the purposes of point 4.2.4 shall be sufficient to permit the proper control of the various combinations to be EU type-approved according to the state of completion of the vehicle and the criteria set-out in point 2.

Point 5 lays down appropriate provisions concerning virtual testing in accordance with Article 27(6) of Regulation (EU) No 167/2013. It shall not apply to the second subparagraph of Article 27(3) of that Regulation.

Delegated act reference | Annex No | Requirements | Restrictions/comments

Regulation (EU) No 1322/2014 | IX | continuous or interrupted roll over behaviour in case of a laterally overturning narrow track tractor with a protective frame mounted in front of the driver’s seat | Section B4

Regulation (EU) No 1322/2014 | XV | Requirements applying to operating space and to access to the driving position | Only requirements related to dimensions and positioning

Regulation (EU) 2015/208 | VII | Requirements on the field of vision and windscreen wipers | Only requirements related to dimensions, positioning and visibility

Regulation (EU) 2015/208 | IX | Requirements on rear view mirrors | Only requirements related to dimensions, positioning and visibility

Regulation (EU) 2015/208 | XII | Requirements on lighting installation | Only requirements related to dimensions, positioning and visibility in point 5 and 6 (with the exception of colorimetric or photometric requirements)

Regulation (EU) 2015/208 | XIII | Requirements on vehicle occupant protection, including interior fittings, head restraints, seat belts, vehicle doors |

Part 2

Only requirements related to dimensions, including detailed shape, and positioning

Regulation (EU) 2015/208 | XIV | Requirements on vehicle exterior and accessories | Only requirements related to dimensions, including detailed shape, and positioning

The following scheme shall be used as a basic structure for describing and conducting virtual testing:

6.1.1. purpose;

6.1.2. structure model;

6.1.3. boundary conditions;

6.1.4. load assumptions;

6.1.5. calculation;

6.1.6. assessment;

6.1.7. Documentation.

The mathematical model shall be supplied by the manufacturer. It shall reflect the complexity of the structure of the vehicle, system and components to be tested in relation to the requirements. The same provisions shall apply mutatis mutandis for testing components or technical units independently from the vehicle.

The mathematical model shall be validated in comparison with the actual test conditions. A physical test shall be conducted for the purposes of comparing the results obtained when using the mathematical model with the results of a physical test. Comparability of the test results shall be proven. For that purpose, manufacturers shall provide the technical service with a correlation report containing the information on the mathematical model and the correlation between the results obtained with such model and those obtained in the physical tests in accordance with the scheme set out in point 6.1. A validation report, confirming the compliance of the mathematical model, shall be drafted by the manufacturer or by the technical service and submitted to the approval authority. Any change made to the mathematical model or to the software likely to invalidate the validation report shall be brought to the attention of the approval authority, which may require that a new validation process is conducted. The flow chart of the validation process is shown in Figure 1 of point 7.

The data and auxiliary tools used for the simulation and calculation shall be made available by the manufacturer and be documented in a suitable way.

At the request of the technical service, the manufacturer shall supply or provide access to the necessary tools, including appropriate software.

6.2.5.

In addition, the manufacturer shall provide appropriate support to the technical service.

6.2.6.

Providing access and support to a technical service does not detract from any obligation of the technical service regarding the skills of its personnel, the payment of licence rights and respect of confidentiality.

The compliance with the requirements set out in Table 1 of point 5.2. may be demonstrated by virtual testing procedures only if these are carried out in accordance with a mathematical model validated in accordance with the requirements set out in point 6.2.2. The applicability and restrictions of the model shall be agreed with the technical services and shall be subject to the approval of the approval authority.

A test report of the virtual testing results shall be provided by the technical service. The test report should be coherent with the correlation report and the validation report and shall include at least the following elements: the building of a virtual prototype, the simulation inputs and the simulation results related to the technical requirements.

For the purposes of this Annex the following definitions shall apply:

1.1. ‘quality management system’ means a set of interrelated or interacting elements that organisations use to direct and control how quality policies are implemented and quality objectives are achieved;

1.2. ‘audit’ means an evidence-gathering process used to evaluate how well audit criteria are being applied; it should be objective, impartial and independent, and the audit process should be both systematic and documented;

1.3. ‘corrective actions’ means a problem-solving process with subsequent steps taken to remove the causes of a nonconformity or undesirable situation and designed to prevent their recurrence;

2.1. The conformity of production procedure aims to ensure that each vehicle, system, component, separate technical unit, part or equipment produced is in conformity with the specification, performance and marking requirements of the approved type.

2.2. Procedures include inseparably the assessment of quality management systems, referred as ‘initial assessment’ and set out in section 3. and verification and production-related controls, referred to as ‘product conformity arrangements’ and set out in section 4.

3.1. Before granting type-approval, the approval authority shall verify the existence of satisfactory arrangements and procedures established by the manufacturer for ensuring effective control so that vehicles, systems, components or separate technical units when in production conform to the approved type.

3.2. Guidelines for quality and/or environmental management systems auditing set out in the EN ISO 19011:2011 standard shall apply to the initial assessment.

3.3. The requirements referred to in point 3.1 shall be verified to the satisfaction of the approval authority granting type-approval. The approval authority shall be satisfied with the initial assessment and the product conformity arrangements in section 4. taking account as necessary of one of the arrangements described in points 3.3.1 to 3.3.3 or a combination of those arrangements in full or in part as appropriate.

3.3.1. The initial assessment and/or verification of product conformity arrangements shall be carried out by the approval authority granting the approval or an appointed body acting on behalf of the approval authority.

3.3.1.1. When considering the extent of the initial assessment to be carried out, the approval authority may take account of available information relating to:

3.3.1.1.1. the manufacturer’s certification described in point 3.3.3, which has not been qualified or recognised under that point;

3.3.1.1.2. in the case of components or separate technical units type-approvals, quality system assessments performed in the component or separate technical unit manufacturer’s premises by vehicle manufacturer(s), according to one or more of the industry sector specifications satisfying the requirements in harmonised standard EN ISO 9001:2008.

3.3.2. The initial assessment and/or verification of product conformity arrangements may also be carried out by the approval authority of another Member State, or the appointed body designated for this purpose by the approval authority.

3.3.2.1. In such a case, the approval authority of the other Member State shall prepare a statement of compliance outlining the areas and production facilities it has covered as relevant to the vehicles, systems, components or separate technical units to be type-approved.

3.3.2.2. On receiving an application for a compliance statement from the approval authority of a Member State granting type-approval, the approval authority of another Member State shall send forthwith the statement of compliance or advise that it is not in a position to provide such a statement.

3.3.2.3. The statement of compliance shall include at least the following:

3.3.2.3.1. group or company (e.g. XYZ automotive);

3.3.2.3.2. particular organisation (e.g. European division);

3.3.2.3.3. plants/sites (e.g. Engine plant 1 (United Kingdom) — vehicle plant 2 (Germany));

3.3.2.3.4. vehicle/component range (e.g. All category T1 models);

3.3.2.3.5. areas assessed (e.g. Engine assembly, body pressing and assembly, vehicle assembly);

3.3.2.3.6. documents examined (e.g. Company and site quality manual and procedures);

3.3.2.3.7. date of the assessment (e.g. Audit conducted from 18 to 30.5.2013);

3.3.2.3.8. planned monitoring visit (e.g. October 2014).

3.3.3. The approval authority shall also accept the manufacturer’s suitable certification to harmonised standard EN ISO 9001:2008 or an equivalent harmonised standard as satisfying the initial assessment requirements of point 3.3. The manufacturer shall provide details of the certification and undertake to inform the approval authority of any revisions to its validity or scope.

3.4. For the purpose of vehicle type-approval, the initial assessments carried out for granting approvals for systems, components and separate technical units of the vehicle need not be repeated but shall be complemented by an assessment covering the locations and activities relating to the assembly of the whole vehicle not covered by the former assessments.

4.1. Every vehicle, system, component or separate technical unit approved pursuant to Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation, pursuant to a UNECE regulation annexed to the Revised 1958 Agreement, or pursuant to a complete test report issued on the basis of OECD Codes listed in Annex II to this Regulation, shall be so manufactured as to conform to the approved type by meeting the requirements of this Annex, Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation, as well as the relevant UNECE regulation(s) and OECD Code(s).

4.2. Before granting a type-approval pursuant to Regulation (EU) No 167/2013 and the delegated and implementing acts adopted pursuant to that Regulation, a UNECE regulation annexed to the Revised 1958 Agreement or an OECD Code, the approval authority of a Member State shall verify the existence of adequate arrangements and documented control plans, to be agreed with the manufacturer for each approval, to carry out at specified intervals those tests or associated checks necessary to verify continued conformity with the approved type, including, where applicable, tests specified in Regulation (EU) No 167/2013, the UNECE regulation and the OECD Code.

4.3. The holder of the type-approval shall, in particular:

4.3.1. ensure the existence and application of procedures for effective control of the conformity of products (vehicles, systems, components or separate technical units) to the approved type;

This article is long: the rest is at the official publication.