1 ANNEX, Commission Regulation (EU) No 1304/2014 of 26 November 2014 on the technical specificati…

In forcesince 28 Sep 2023

Technical Specifications for Interoperability (TSI) lay down the optimal level of harmonised specifications for each subsystem (or part of it), to ensure the safety and interoperability of the rail system, to facilitate, improve and develop rail transport services within the Union and with third countries, and to contribute to the completion of the single European railway area and the progressive achievement of the internal market. The specifications of the TSIs must meet the essential requirements as set out in Annex III to Directive (EU) 2016/797.

In accordance with the proportionality principle, this TSI sets out the optimal level of harmonisation related to specifications on the rolling stock subsystem as defined in point 1.1 intended to limit the noise emission of the rail system within the Union.

This TSI applies to all rolling stock within the scope of the Annex to Regulation (EU) No 1302/2014 (‘TSI LOC&PAS’) and the Annex to Regulation (EU) No 321/2013 (‘TSI WAG’).

Alongside with the Annex to Commission Implementing Regulation (EU) 2019/773 [Commission Implementing Regulation (EU) 2019/773 of 16 May 2019 on the technical specification for interoperability relating to the operation and traffic management subsystem of the rail system within the European Union and repealing Decision 2012/757/EU (OJ L 139I, 27.5.2019, p. 5).] (‘TSI OPE’), this TSI applies to the operation of freight wagons, which are used on railway infrastructure designated as ‘quieter routes’.

The geographical scope of this TSI corresponds to the scopes defined in point 1.2 of LOC&PAS TSI and in point 1.2 of WAG TSI, each for their rolling stock (RST) concerned.

A ‘unit’ means the rolling stock, which is subject to the application of this TSI, and therefore subject to the ‘EC’ verification procedure. Chapter 2 of LOC&PAS TSI and Chapter 2 of WAG TSI describe what a unit can consist of.

The requirements of this TSI apply to the following categories of rolling stock set out in Section 2 of Annex I to Directive (EU) 2016/797:

(a)

locomotives and passenger rolling stock including thermal or electric traction units, self-propelling thermal or electric passenger trains, and passenger coaches. This category is further defined in Chapter 2 of LOC&PAS TSI and shall be referred to in this TSI as locomotives, electric multiple units (EMU), diesel multiple units (DMU) and coaches;

(b)

freight wagons, including low-deck vehicles designed for the entire network and vehicles designed to carry lorries. This category is further defined in Chapter 2 of WAG TSI and shall be referred to in this TSI as wagons;

(c)

special vehicles, such as on-track machines. This category is further defined in Chapter 2 of LOC&PAS TSI.

All basic parameters set out in this TSI shall be linked to at least one of the essential requirements as set out in Annex III to Directive (EU) 2016/797. Table 1 indicates the allocation.

Point | Basic parameter | Essential requirements

Safety | Reliability and availability | Health | Environ-mental protection | Technical compatibility | Accessibility

4.2.1 | Limits for stationary noise | | | | 1.4.4 | |

4.2.2 | Limits for starting noise | | | | 1.4.4 | |

4.2.3 | Limits for pass-by noise | | | | 1.4.4 | |

4.2.4 | Limits for driver's cab interior noise | | | | 1.4.4 | |

This Chapter sets out the optimal level of harmonisation related to specifications on the rolling stock subsystem intended to limit the noise emission of the Union rail system and to achieve interoperability.

The following parameters have been identified as critical for the interoperability (basic parameters):

(a)

‘stationary noise’;

(b)

‘starting noise’;

(c)

‘pass-by noise’;

(d)

‘driver's cab interior noise’.

The corresponding functional and technical specifications allocated to the different categories of rolling stock are set out in this point. In case of units equipped with both thermal and electric power, the relevant limit values under all normal operation modes shall be respected. If one of those operation modes plans the use of both thermal and electric power at the same time, the less restrictive limit value applies. In accordance with Article 4(5) and Article 2(13) of Directive (EU) 2016/797, provision may be made for specific cases. Such provisions are indicated in point 7.3.

The assessment procedures for the requirements in this point are defined in the indicated points of Chapter 6.

The limit values for the following sound pressure levels under normal vehicle conditions concerning the stationary noise allocated to the categories of the rolling stock subsystem are set out in Table 2:

(a)

the A-weighted equivalent continuous sound pressure level of the unit (LpAeq,T[unit]);

(b)

the A-weighted equivalent continuous sound pressure level at the nearest measuring position i considering the main air compressor (LipAeq,T);

(c)

the AF-weighted sound pressure level at the nearest measuring position i considering impulsive noise of the exhaust valve of the air dryer (LipAFmax).

The limit values are set at a distance of 7,5 m from the centre of the track and 1,2 m above top of rail.

Category of the rolling stock subsystem | LpAeq,T[unit] [dB] | LipAeq,T [dB] | LipAFmax [dB]

Electric locomotives and special vehicles with electric traction | 70 | 75 | 85

Diesel locomotives and special vehicles with diesel traction | 71 | 78

EMUs | 65 | 68

DMUs | 72 | 76

Coaches | 64 | 68

Wagons | 65 | n.a. | n.a.

The demonstration of conformity is described in point 6.2.2.1.

The limit values for the AF-weighted maximum sound pressure level (LpAF,max) concerning the starting noise allocated to the categories of the rolling stock subsystem are set out in Table 3. The limit values are set at a distance of 7,5 m from the centre of the track and 1,2 m above top of rail.

Category of the rolling stock subsystem | LpAF,max [dB]

Electric locomotives with total tractive power P < 4500 kW | 81

Electric locomotives with total tractive power P ≥ 4500 kW

Special vehicles with electric traction

84

Diesel locomotives P < 2000 kW at the engine output shaft | 85

Diesel locomotives P ≥ 2000 kW at the engine output shaft

Special vehicles with diesel traction

87

EMUs with a maximum speed vmax < 250 km/h | 80

EMUs with a maximum speed vmax ≥ 250 km/h | 83

DMUs P < 560 kW/engine at the engine output shaft | 82

DMUs P ≥ 560 kW/engine at the engine output shaft | 83

The demonstration of conformity is described in point 6.2.2.2.

The limit values for the A-weighted equivalent continuous sound pressure level at a speed of 80 km/h (LpAeq,Tp,(80 km/h)) and, if applicable, at 250 km/h (LpAeq,Tp,(250 km/h)) concerning the pass-by noise allocated to the categories of the rolling stock subsystem are set out in Table 4. The limit values are set at a distance of 7,5 m from the centre of the track and 1,2 m above top of rail.

Measurements at speeds higher than or equal to 250 km/h shall also be made at the ‘additional measurement position’ with a height of 3,5 m above top of rail in accordance with the specification referenced in Appendix B, Index [1] and assessed against the applicable limit values of Table 4.

[APL: the number of axles divided by the length over the buffers (m-1)]

Category of the rolling stock subsystem | LpAeq,Tp (80 km/h) [dB] | LpAeq,Tp (250 km/h) [dB]

Electric locomotives and special vehicles with electric traction | 84 | 99

Diesel locomotives and special vehicles with diesel traction | 85 | n.a.

EMUs | 80 | 95

DMUs | 81 | 96

Coaches | 79 | n.a.

Wagons (normalised to APL = 0,225) | 83 | n.a.

The demonstration of conformity is described in point 6.2.2.3.

The friction element for wheel tread brakes (i.e. brake block) has an influence on the pass-by noise by creating roughness on the wheel tread when braking.

The demonstration of conformity of brake blocks for freight wagons is described in point 6.1.2.1 of this TSI. Conformity of its brake blocks to that point does not exempt the unit under assessment from the requirements set out in point 4.2.3 and the demonstration of conformity set out in point 6.2.2.3.

The limit values for the A-weighted equivalent continuous sound pressure level (LpAeq,T) concerning the noise within the driver's cab of electric and diesel locomotives, EMUs, DMUs and coaches fitted with a cab are set out in Table 5. The limit values are set in the vicinity of the driver's ear.

These limit values are not mandatory for special vehicles. However, the demonstration of conformity referred to in point 6.2.2.4 shall be performed and the resulting values shall be recorded in the technical file.

Noise within the driver's cab | LpAeq,T [dB]

At standstill with horns sounding | 95

At maximum speed vmax if vmax < 250 km/h | 78

At maximum speed vmax if 250 km/h ≤ vmax < 350 km/h | 80

The demonstration of conformity is described in point 6.2.2.4.

This TSI has the following interfaces with the rolling stock subsystem:

Interface with subsystems referred to in Chapter 2, points (a) and (c), of this Annex (dealt with in LOC&PAS TSI) with regard to:

stationary noise,

starting noise (not applicable to coaches),

pass-by noise,

interior noise within the driver's cab, where applicable.

Interface with subsystems referred to in Chapter 2, point (b), of this Annex (dealt with in WAG TSI) with regard to:

pass-by noise,

stationary noise.

This TSI has the following interface with OPE TSI with regard to:

pass-by noise.

Requirements concerning the operating rules for the subsystem rolling stock are set out in point 4.4 of LOC&PAS TSI and in point 4.4 of WAG TSI.

The contingency arrangements as set out in point 4.2.3.6.3 of OPE TSI include the operation of wagons not compliant with point 7.2.2.2 of this Annex on quieter routes.

This measure can be applied to address capacity restrictions or operational constraints caused by rolling stock failures, extreme weather conditions, accidents or incidents and infrastructure failures.

The operation of wagons not compliant with point 7.2.2.2 on quieter routes shall be possible in case of wagons maintenance activities where only a quieter route is available in order to access the maintenance workshop.

Contingency arrangements set out in point 4.4.1 are applicable in case of infrastructure works where a quieter route is the only suitable alternative.

Requirements concerning the maintenance rules for the subsystem rolling stock are set out in point 4.5 of TSI LOC&PAS and in point 4.5 of TSI WAG.

Not applicable.

See Article 6.

Interoperability constituents (ICs), as defined in Article 2(7) of Directive (EU) 2016/797, are listed in point 5.2 of this Annex together with the reference to corresponding requirements set out in point 4.2 of this Annex.

This interoperability constituent is only applicable to the ‘rolling stock - freight wagons’ subsystem.

A friction element for wheel tread brakes shall comply with the requirements set out in point 4.2.3.a. Those requirements shall be assessed at IC level.

The conformity assessment of an interoperability constituent shall be performed in accordance with the module(s) described in Table 5a.

Module CB | EC-Type examination

Module CD | Conformity to type based on quality management system of the production process

Module CF | Conformity to type based on product verification

Module CH1 | Conformity based on full quality management system plus design examination

Those modules are specified in detail in Decision 2010/713/EU.

The manufacturer or his authorised representative established within the Union shall choose one of the modules or module combinations indicated below for the constituent ‘Friction element for wheel tread brakes’:

CB+CD,

CB+CF,

CH1.

Within the application of the chosen module or combination of modules, the interoperability constituent shall be assessed against the requirements set out in point 4.2. If necessary, additional requirements concerning the assessment of particular interoperability constituents are defined in the following points.

A friction element for wheel tread brakes of freight wagons shall comply with the requirements set out in Appendix F.

Until the end of the transition period set out in Appendix G, the types of friction elements for wheel tread brakes listed in Appendix G are deemed compliant with the requirements set out in Appendix F without testing.

The EC verification shall be performed in accordance with the module(s) described in Table 6.

SB | EC-Type Examination

SD | EC verification based on quality management system of the production process

SF | EC verification based on product verification

SH1 | EC verification based on full quality management system plus design examination

Those modules are specified in detail in Decision 2010/713/EU.

The applicant shall choose one of the following assessment procedures consisting of one or more modules for the EC verification of the subsystem:

(SB+SD),

(SB+SF),

(SH1).

Within the application of the chosen module or module combination the subsystem shall be assessed against the requirements set out in point 4.2. If necessary, additional requirements concerning the assessment are given in the following points.

The demonstration of conformity with the limit values on stationary noise as set out in point 4.2.1 shall be carried out in accordance with the specification referenced in Appendix B, Index [1].

For the assessment of the main air compressor noise at the nearest measuring position i, the LipAeq,T indicator shall be used with T representative of one operating cycle as defined in the specification referenced in Appendix B, Index [1]. Only the train systems that are required for the air compressor to run under normal operating conditions shall be used for that purpose. The train systems which are not needed for the operation of the compressor may be switched off to prevent contribution to the noise measurement. The demonstration of conformity with the limit values shall be carried out under the conditions solely necessary for operation of the main air compressor at the lowest rpm.

For the assessment of the impulsive noise sources at the nearest measuring position i, the LipAFmax indicator shall be used. The relevant noise source is the exhaust from the valves of the air dryer.

The demonstration of conformity with the limit values on starting noise as set out in point 4.2.2 shall be carried out in accordance with the specification referenced in Appendix B, Index [1]. The maximum level method shall apply. Deviating from the test procedure of the specification, the train shall accelerate from standstill up to 30 km/h and then maintain the speed.

In addition the noise shall be measured at the same distance from the centre of the track and the same height above top of rail as set out in point 4.2.2. The ‘averaged level method’ and the ‘maximum level method’ in accordance with the specification referenced in Appendix B, Index [1] shall apply and the train shall accelerate from standstill up to 40 km/h and then maintain the speed. The measured values are not assessed against any limit value and shall be recorded in the technical file and communicated to the Agency.

For special vehicles the starting procedure shall be performed without additional trailer loads.

The demonstration of conformity with the limit values on pass-by noise as set out in point 4.2.3 shall be carried out in accordance with points 6.2.2.3.1 and 6.2.2.3.2.

The tests shall be performed on a reference track as defined in the specification referenced in Appendix B, Index [1].

However, it is permitted to carry out the test on a track that does not comply with the reference track conditions in terms of acoustic rail roughness level and track decay rates as long as the noise levels measured in accordance with point 6.2.2.3.2 do not exceed the limit values set out in point 4.2.3.

The acoustic rail roughness and the decay rates of the test track shall be determined in any case. If the track on which the tests are performed does meet the reference track conditions, the measured noise levels shall be marked ‘comparable’, otherwise they shall be marked ‘non-comparable’. It shall be recorded in the technical file whether the measured noise levels are ‘comparable’ or ‘non-comparable’.

The measured acoustic rail roughness values of the test track remain valid during a period starting 3 months before and ending 3 months after that measurement, provided that during that period no track maintenance has been performed which influences the rail acoustic roughness.

The measured track decay rate values of the test track shall remain valid during a period starting 1 year before and ending 1 year after that measurement, provided that during that period no track maintenance has been performed which influences the track decay rates.

Confirmation shall be provided in the technical file that the track data related to the type's pass-by noise measurement were valid during the day(s) of testing, e.g. by providing the date of last maintenance having an impact on noise.

Furthermore, it is permitted to carry out tests at speeds equal to or higher than 250 km/h on slab tracks. In that case the limit values shall be 2 dB higher than those set out in point 4.2.3.

The tests shall be carried out in accordance with the specification referenced in Appendix B, Index [1]. Any comparison against limit values shall be carried out with results rounded to the nearest integer decibel. Any normalisation shall be performed before rounding. The detailed assessment procedure is set out in points 6.2.2.3.2.1, 6.2.2.3.2.2 and 6.2.2.3.2.3.

For EMU, DMUs, locomotives and coaches three classes of maximum operational speed are distinguished:

(1)

If the maximum operational speed of the unit is lower than or equal to 80 km/h, the pass-by noise shall be measured at its maximum speed vmax. That value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.

(2)

If the maximum operational speed vmax of the unit is higher than 80 km/h and lower than 250 km/h, the pass-by noise shall be measured at 80 km/h and at its maximum speed. Both measured pass-by noise values LpAeq,Tp(Vtest) shall be normalised to the reference speed of 80 km/h LpAeq,Tp(80 km/h) using Formula (1). The normalised value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.

Formula (1):

LpAeq,Tp(80 km/h) = LpAeq,Tp(Vtest) – 30 * log (vtest/80 km/h)

vtest | = | Actual speed during the measurement

(3)

If the maximum operational speed vmax of the unit is equal to or higher than 250 km/h, the pass-by noise shall be measured at 80 km/h and at its maximum speed with an upper test speed limit of 320 km/h. The measured pass-by noise value LpAeq,Tp(Vtest) at 80 km/h shall be normalised to the reference speed of 80 km/h LpAeq,Tp(80 km/h) using Formula (1). The normalised value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3. The measured pass-by noise value at maximum speed LpAeq,Tp(Vtest) shall be normalised to the reference speed of 250 km/h LpAeq,Tp(250 km/h) using Formula (2). The normalised value shall not exceed the limit value LpAeq,Tp(250 km/h) as set out in point 4.2.3.

Formula (2):

LpAeq,Tp(250 km/h) = LpAeq,Tp(Vtest) – 50 * log(vtest/250 km/h)

vtest | = | Actual speed during the measurement

For wagons two classes of maximum operational speed are distinguished:

(1)

If the maximum operational speed vmax of the unit is lower than or equal to 80 km/h, the pass-by noise shall be measured at its maximum speed. The measured pass-by noise value LpAeq,Tp(Vtest) shall be normalised to a reference APL of 0,225 m-1 LpAeq,Tp (APLref) using Formula (3). That value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.

Formula (3):

LpAeq,Tp (APLref) = LpAeq,Tp(Vtest) – 10 * log(APLwag/0,225 m-1)

APLwag | = | Number of axles divided by the length over the buffers [m-1]

vtest | = | Actual speed during the measurement

(2)

If the maximum operational speed vmax of the unit is higher than 80 km/h, the pass-by noise shall be measured at 80 km/h and at its maximum speed. Both measured pass-by noise values LpAeq,Tp(Vtest) shall be normalised to the reference speed of 80 km/h and to a reference APL of 0,225 m-1 LpAeq,Tp(APL ref, 80 km/h) using Formula (4). The normalised value shall not exceed the limit value LpAeq,Tp(80 km/h) as set out in point 4.2.3.

Formula (4):

LpAeq,Tp (APLref, 80 km/h) = LpAeq,Tp(Vtest) – 10 * log(APLwag/0,225 m-1) — 30 * log(vtest/80 km/h)

APLwag | = | Number of axles divided by the length over the buffers [m-1]

vtest | = | Actual speed during the measurement

For special vehicles the same assessment procedure as set out in 6.2.2.3.2.1 applies. The measuring procedure shall be performed without additional trailer loads.

Special vehicles are deemed to comply with the pass-by noise level requirements in point 4.2.3 without measuring when they are:

solely braked by either composite brake blocks or disc brakes, and

equipped with composite scrubbers, if scrubber blocks are fitted.

The demonstration of conformity with the limit values on the driver's cab interior noise as set out in point 4.2.4 shall be carried out in accordance with the specification referenced in Appendix B, Index [2]. For special vehicles the measuring procedure shall be performed without additional trailer loads.

Instead of the test procedures as set out in point 6.2.2, it is permitted to substitute some or all of the tests by a simplified evaluation. The simplified evaluation consists of acoustically comparing the unit under assessment to an existing type (further referred to as the reference type) with documented noise characteristics.

The simplified evaluation may be used for each of the applicable basic parameters ‘stationary noise’, ‘starting noise’, ‘pass-by noise’ and ‘driver's cab interior noise’ autonomously and shall consist of providing evidence that the effects of the differences of the unit under assessment do not result in exceeding the limit values set out in point 4.2.

For the units under simplified evaluation, the proof of conformity shall include a detailed description of the noise relevant changes compared to the reference type. On the basis of that description, a simplified evaluation shall be performed. The estimated noise values shall include the uncertainties of the applied evaluation method. The simplified evaluation can either be a calculation and/or simplified measurement.

A unit certified on the basis of the simplified evaluation method shall not be used as a reference unit for a further evaluation.

If the simplified evaluation is applied for pass-by noise, the reference-type shall comply with at least one of the following:

Chapter 4 of this Annex and for which the pass-by noise results are marked ‘comparable’,

Chapter 4 of the Annex to Decision 2011/229/EU and for which the pass-by noise results are marked ‘comparable’,

Chapter 4 of the Annex to Decision 2006/66/EC,

This article is long: the rest is at the official publication.