Annex number | Annex title
C1 Vehicle construction and general type-approval requirements
I | List of UNECE regulations which apply on a compulsory basis
II | Requirements applying to powertrain tampering prevention (anti-tampering) measures
III | Requirements applying to arrangements for type-approval procedures
IV | Requirements applying to conformity of production (CoP)
V | Requirements applying to coupling devices and attachments
VI | Requirements applying to devices to prevent unauthorised use
VII | Requirements applying to electromagnetic compatibility (EMC)
VIII | Requirements applying to external projections
IX | Requirements applying to fuel storage
X | Requirements applying to load platforms
XI | Requirements applying to masses and dimensions
XII | Requirements applying to functional on-board diagnostics (OBD)
XIII | Requirements applying to passenger handholds and footrests
XIV | Requirements applying to the registration plate space
XV | Requirements applying to access to repair and maintenance information
XVI | Requirements applying to stands
C2 Requirements of technical services
XVII | Performance standards and assessment of technical services
UNECE regulation No | Subject | Series of amendments | OJ reference | Applicability
10 | Electromagnetic compatibility (EMC) | Supplement 1 to the 04 series of amendments | OJ L 254, 20.9.2012, p. 1. | L1e, L2e, L3e, L4e, L5e, L6e and L7e
62 | Protection against unauthorised use | Supplement 2 to the 00 series of amendments | OJ L 89, 27.3.2013, p. 37. | L1e, L2e, L3e, L4e, L5e, L6e and L7e
155 | Cyber security and cyber security management system | Supplement 3 to the 00 series of amendments | OJ L, 2025/5, 10.1.2025, ELI: http://data.europa.eu/eli/reg/2025/5/oj | L1e, L2e, L3e, L4e, L5e, L6e and L7e, except L1e category vehicles designed to pedal referred to in Article 3, point (94)(b), of Regulation (EU) No 168/2013
Explanatory note: The fact that a component is included in this list does not make its installation mandatory. For certain components, however, mandatory installation requirements are laid down in other annexes to this Regulation.
1.1.
The powertrain tampering prevention (anti-tampering) measures are aimed at ensuring that adverse changes to the vehicle's powertrain which have negative impacts on functional safety and/or on the environment are discouraged.
1.2.
The measures shall include special requirements on vehicle markings as regards maximum power, maximum design vehicle speed and stationary sound level on the statutory plate referred to in Article 39(1) of Regulation (EU) No 168/2013. The special marking of original and non-original components, separate technical units, parts and equipment affecting environmental and propulsion unit performance and functional safety shall comply with Article 39(2) and (3) of Regulation (EU) No 168/2013 in order to allow enforcement authorities to verify whether parts and equipment fitted to a vehicle in use are appropriate for the type-approved vehicle.
All L-category vehicles referred to in Article 2 of Regulation (EU) No 168/2013, with the exception of (sub)categories L3e-A3, L4e-A3 and L5e.
2.1.
The manufacturer shall ensure that the approval authority and technical service is provided with the necessary information and, where appropriate, the necessary vehicles, propulsions, components and separate technical units to enable them to verify that the requirements of this Annex have been met.
2.2.
The manufacturer shall declare in the application for the type-approval its commitment not to market interchangeable components which could enable an increase in propulsion unit performance applicable to the relevant (sub)category.
2.3.
Interchangeability of non-identical parts between type-approved vehicles:
2.3.1.
The interchangeability of the following parts in an individual or combined way, shall not result in an increase of the propulsion unit performance exceeding the values measured and reported at type-approval meaning that in any case the maximum design vehicle speed and/or the maximum continuous rated and/or net engine power of the relevant category shall remain within the conformity of production boundaries set out in point 4.1.4 of Annex IV:
2.3.1.1. for vehicles equipped with a two-stroke engine: cylinder, piston, carburettor or fuel injector(s), intake pipe, exhaust system;
2.3.1.2. for vehicles equipped with a four-stroke engine: cylinder head, camshaft, cylinder, piston, carburettor or fuel injector(s), intake pipe, exhaust system.
2.4.
In no case may the approved maximum design vehicle speed and/or the maximum continuous rated and/or net engine power of the relevant (sub)category, set out in Annex I to Regulation (EU) No 168/2013 may, be exceeded meaning that in any case the vehicle’s propulsion unit performance shall remain within the conformity of production boundaries set out in point 4.1.4 of Annex IV.
2.5.
In the case of chains or cogged belts, the number of teeth shall be displayed on the pinions.
2.6.
The manufacturer shall declare that manufacturer-facilitated modifications of the following characteristics will not increase the propulsion unit performance exceeding the conformity of production boundaries set out in point 4.1.4 of Annex IV: spark delivery of the ignition system if applicable, fuel feed and delivery system, air intake system including air filter(s) (modification or removal), propulsion battery configuration or electric power to the electric motor(s) if applicable, the drive train and the control unit(s) that control the powertrain of the vehicle.
2.7.
If the ignition timing is adjustable, the propulsion unit performance shall be measured with the ignition advance set within ± 5° of the value at which maximum engine power is achieved.
2.8.
The manufacturer shall ensure that the approved vehicle complies with the following provisions on electronic system security limiting the vehicle’s environmental and propulsion unit performance.
2.8.1.
For a vehicle equipped with (an) electrical/electronic device(s) which limit its propulsion unit performance, the vehicle manufacturer shall provide data and evidence to the test authorities to demonstrate that modification or disconnection of the device or its wiring system will not increase performance.
2.8.2.
Any vehicle equipped with electronic control shall include features to prevent modification, except as permitted by the manufacturer. The manufacturer shall permit modifications necessary for the diagnosis, servicing, inspection, retrofitting or repair of the vehicle.
2.8.3.
Any reprogrammable computer codes or operating parameter shall be resistant to tampering and afford a level of protection at least as high as the provisions in ISO 15031-7:2001, provided that the security exchange is conducted using the communication protocols and standardised diagnostic connector prescribed in Appendix 1 to Annex XII.
2.8.4.
To avoid increases in propulsion unit performance, computer-coded propulsion operating parameters shall not be changeable without the use of specialised tools and procedures, e.g. soldered or potted computer components, sealed or soldered computer enclosures.
2.8.5.
Any removable calibration memory chips shall be potted, encased in a sealed container or protected by electronic algorithms, and shall not be changeable without the use of specialised tools and procedures.
2.8.6.
Manufacturers using programmable computer code systems (e.g. electrical erasable programmable read-only memory, EEPROM) shall deter unauthorised reprogramming. They shall include enhanced tamper-protection strategies and write-protect features requiring electronic access to an off-site computer maintained by the manufacturer and to which independent operators shall also have access using the protection afforded in Annex XV. Methods giving an adequate level of tamper protection, such as seed and key security access as per Keyword 2000 protocol, shall be approved by the approval authority.
2.8.7.
Stored on-board diagnostic trouble codes (DTCs) in the powertrain or engine control unit(s) shall not be erased by disconnection of the on board computer from the vehicle power supply or by disconnection or failure of the vehicle battery or ground.
3.1.
The acceptable tolerance for maximum vehicle speed and/or power limitation of category L1e, L2e and L6e vehicles shall be ± 5 % of the maximum design vehicle speed and/or net and/or continuous rated power classification criteria referred to in Annex I to Regulation (EU) No 168/2013.
3.2.1.1. Each intake pipe shall be fixed with shear-bolts or bolts removable only using special tools. A restricted section, indicated on the outside, shall be located inside the pipes; at that point the wall shall be less than 4 mm in thickness, or 5 mm if composed of a flexible material such as rubber.
3.2.1.2. Any interference with the pipes aimed at modifying the restricted section shall lead to either the destruction of the pipes or complete and permanent malfunctioning of the engine until they are restored to their approved condition.
3.2.1.3. A marking with indication of the vehicle (sub-) category as defined in Articles 2 and 4 of, and Annex I to, Regulation (EU) No 168/2013 shall be legible on the pipes.
3.2.2.1. If an engine is equipped with (a) reed valve(s), it (they) shall be fixed with shear-bolts which prevent reuse of its support or bolts removable only using special tools.
3.2.2.2. After mounting, the maximum thickness of a cylinder-head gasket, if any, shall not exceed 1,3 mm.
3.2.2.3. Piston for two-stroke engines.
The piston, when in position at top dead centre, shall not cover the inlet port. This requirement does not apply to those parts of the transfer/scavenging port which coincide with the inlet port in the case of vehicles the engine of which is equipped with an induction system incorporating reed valve(s).
3.2.2.4. For two-stroke engines, rotation of the piston through 180° shall not increase engine performance.
3.2.2.5. For two-stroke engines, the maximum thickness of any gasket between the base of the cylinder and the crankcase, if any, may not exceed 0,5 mm, after mounting.
3.2.3.1. No artificial restriction is permitted in the exhaust system. The valve guides of a four-stroke engine are not to be considered artificial restrictions.
3.2.3.2. Removing the resonator tube, if installed, shall not result in an increase in propulsion unit performance.
3.2.3.3. The part(s) of the exhaust system inside the silencer(s) which determine(s) the effective length of the exhaust pipe shall be affixed to the silencer(s) or expansion box(es) in such a way that it (they) cannot be removed.
3.3.1. CVT Transmission covers, if available, shall be fixed by means of at a minimum 2 shear bolts or be disassembled only by using special tools.
3.3.2. The CVT mechanism intended to limit the drive ratio by limitation of the effective distance between two discs shall be fully integrated in one or both discs in such a way that it is impossible to modify the effective distance beyond a limit that would result in an increase of the maximum vehicle speed of more than 10 % of this maximum permissible vehicle speed without destroying the disc system. If the manufacturer employs interchangeable spacer rings in the CVT to adjust the maximum vehicle speed, the complete removal of these rings shall not increase the maximum vehicle speed with more than 10 %.
3.5.1.
CVT Transmission covers, if available, shall be fixed by means of at a minimum 2 shear bolts or be disassembled only by using special tools.
3.5.2.
The CVT mechanism intended to limit the drive ratio by limitation of the effective distance between two discs shall be fully integrated in one or both discs in such a way that it is impossible to modify the effective distance beyond a limit that would result in an increase of the maximum vehicle speed of more than 10 % of this maximum permissible vehicle speed without destroying the disc system. If the manufacturer employs interchangeable spacer rings in the CVT to adjust the maximum vehicle speed, the complete removal of these rings shall not increase the maximum vehicle speed with more than 10 %.
4.1.
Subcategory L3e-A1 and L4e-A1 vehicles shall comply with the requirements of either points 4.2. to 4.2.3., or points 4.3., 4.3.1. and 4.3.2., or points 4.4., 4.4.1. and 4.4.2., and with points 4.5., 4.6. and 4.7. In addition, they shall comply the requirements of points 3.2.2.1., 3.2.2.3., 3.2.2.4., 3.2.2.5., 3.2.3.1. and 3.2.3.3.
4.2.
An irremovable sleeve must be located in the inlet conduit. If such a sleeve is located in the intake pipe, the latter shall be fixed to the engine block by means of shear-bolts or bolts removable only using special tools.
4.2.1.
The sleeve shall have a minimum hardness of 60 HRC. In the restricted section it shall not exceed 4 mm in thickness.
4.2.2.
Any interference with the sleeve aimed at removing or modifying it shall lead to either the destruction of the sleeve and its support or complete and permanent malfunctioning of the engine until it is restored to its approved condition.
4.2.3.
A marking with indication of the vehicle (sub-) category as defined in Articles 2 and 4 of, and Annex I to, Regulation (EU) No 168/2013 shall be legible on the surface of the sleeve or not far from it.
4.2.4.
A marking with indication of the vehicle category or categories shall be legible on the surface of the sleeve or not far from it.
4.2.5.
Each intake pipe shall be fixed with shear-bolts or bolts removable only using special tools. A restricted section, indicated on the outside, shall be located inside the pipes; at that point the wall shall be less than 4 mm in thickness, or 5 mm if composed of a flexible material such as rubber.
4.2.6.
Any interference with the pipes aimed at modifying the restricted section shall lead to either the destruction of the pipes or complete and permanent malfunctioning of the engine until they are restored to their approved condition.
4.2.7.
A marking with indication of the vehicle (sub)category as defined in Articles 2 and 4 of, and Annex I to, Regulation (EU) No 168/2013 shall be legible on the pipes.
4.2.8.
The part of the inlet conduit located in the cylinder head shall have a restricted section. In the whole inlet passage, there shall not be a more restricted section (except the valve-seat section).
4.2.9.
Any interference with the conduit aimed at modifying the restricted section shall lead to either the destruction of the pipe or complete and permanent malfunctioning of the engine until it is restored to its approved condition.
4.2.10.
A marking with indication of the vehicle category as referred to in Article 39 of Regulation (EU) No 168/2013 shall be legible on the cylinder head.
4.2.11.
The diameter of the restricted sections referred to in point 4.2 may vary according to the (sub)category vehicle concerned.
4.2.12.
The manufacturer shall supply the diameter(s) of the restricted section(s) and demonstrate to the approval authority and technical service that this restricted section is the most critical for the passage of gases, and that there is no other section which, if modified, could increase propulsion unit performance.
4.3.
Each intake pipe shall be fixed with shear-bolts or bolts removable only using special tools. A restricted section, indicated on the outside, shall be located inside the pipes; at that point the wall shall be less than 4 mm in thickness, or 5 mm if composed of a flexible material such as rubber.
4.3.1.
Any interference with the pipes aimed at modifying the restricted section shall lead to either the destruction of the pipes or complete and permanent malfunctioning of the engine until they are restored to their approved condition.
4.3.2.
A marking with indication of the vehicle (sub-) category as defined in Articles 2 and 4 of, and Annex I to, Regulation (EU) No 168/2013 shall be legible on the pipes.
4.4.
The part of the inlet conduit located in the cylinder head shall have a restricted section. In the whole inlet passage, there shall not be a more restricted section (except the valve-seat section).
4.4.1.
Any interference with the conduit aimed at modifying the restricted section shall lead to either the destruction of the pipe or complete and permanent malfunctioning of the engine until it is restored to its approved condition.
4.4.2.
A marking with indication of the vehicle category as defined in Articles 2 and 4 of, and Annex I to, Regulation (EU) No 168/2013 shall be legible on the cylinder head.
4.5.
The diameter of the restricted sections referred to in point 4.2. may vary according to the (sub-) category vehicle concerned.
4.6.
The manufacturer shall supply the diameter(s) of the restricted section(s) and demonstrate to the approval authority and technical service that this restricted section is the most critical for the passage of gases, and that there is no other section which, if modified, could increase propulsion unit performance.
4.7.
After mounting, the maximum thickness of a cylinder-head gasket shall not exceed 1,6 mm.
5.1.
Any variant or version under the same type of vehicle of subcategory L3e-A2 or of subcategory L4e-A2 complying with the conversion requirements set out in point 4 of Annex III, shall not be derived from a L3e-A3 or L4e-A3 type, variant or version with a maximum net engine power and/or maximum continuous rated power more than twice the values set out in the classification of subcategories L3e-A2 or L4e-A2 in Annex I to Regulation (EU) No 168/2013 (e.g. 70 kW to 35 kW or lower, 50 kW to 35 kW or lower).
5.2.
The manufacturer shall declare that modifications and interchangeability of the characteristics and components listed below shall not lead to:
for vehicles of subcategory L3e-A2 and L4e-A2, exceeding the double of the net engine power or maximum continuous rated power, or
for vehicles of category L7e, exceeding the approved propulsion unit performance;
5.2.1.
spark delivery of the ignition system, if applicable;
5.2.2.
fuel feed and delivery system;
5.2.3.
air intake system including air filter(s) (modification or removal);
5.2.4.
the drive train;
5.2.5.
the control unit(s) that control(s) the propulsion unit performance of the powertrain;
5.2.6.
removal of any component (mechanical, electrical, structural, etc.) which limits full engine load leading to any change in the propulsion unit performance approved in accordance with Annex II(A) to Regulation (EU) No 168/2013;
5.2.7.
removal of any component (mechanical, electrical, structural, etc.) which limits full engine load leading to any change in the propulsion unit performance approved in accordance with Annex II(A) to Regulation (EU) No 168/2013.
6.1. The parts, equipment and components listed below shall be durably and indelibly marked with code number(s) and symbols assigned for identification purposes either by the vehicle manufacturer or by the manufacturer of such (replacement) parts, equipment or components. Such marking may take the form of a label provided that it remains legible in normal use and cannot be detached without being destroyed.
6.2. The marking referred to in point 6.1. shall in principle be visible without dismantling the part in question or other parts of the vehicle. Where the bodywork or other parts of the vehicle obscure a marking, the vehicle manufacturer shall provide the competent authorities with indications for opening or dismantling the parts in question and the location of the marking.
6.3. The characters, figures or symbols used shall be at least 2,5 mm in height and be easily legible.
6.4. The parts, equipment and components referred to in point 6.1. are the following, for all (sub)categories:
6.4.1. any electrical/electronic device for the purpose of combustion engine or electric propulsion motor management (ECU ignition module, injectors, intake air temperature etc.),
6.4.2. carburettor or equivalent device,
6.4.3. catalytic converter(s) (only if not integrated in the silencer),
6.4.4. crankcase,
6.4.5. cylinder,
6.4.6. cylinder head,
6.4.7. exhaust pipe(s) (if separate from the silencer),
6.4.8. inlet pipe (if cast separately from the carburettor or cylinder or crankcase),
6.4.9. intake silencer (air filter),
6.4.10. restricted section (sleeve or other),
6.4.11. noise abatement device (silencer(s)),
6.4.12. transmission driven part (rear chain wheel (sprocket) or pulley),
6.4.13. transmission driving part (front chain wheel (sprocket) or pulley).
6.5. In addition, for categories L1e, L2e, and L6e, the following parts, equipment and components shall be marked in accordance with point 6.1.:
6.5.1. transmission CVT,
6.5.2. transmission controller.
1.1. When receiving an application for vehicle type-approval, the approval authority shall:
1.1.1. verify that all EU type-approval certificates issued pursuant to the regulatory acts which are applicable for vehicle type-approval cover the vehicle type and correspond to the prescribed requirements;
1.1.2. by reference to the documentation make sure that the vehicle specifications and data contained in the vehicle information document are included in the data in the information packages and in the EU type-approval certificates in respect of the relevant regulatory acts;
1.1.3. when an item number in the information document is not included in the information package of any of the regulatory acts, confirm that the relevant part or characteristic conforms to the particulars in the information folder;
1.1.4. on a selected sample of vehicles from the type to be approved carry out or arrange to be carried out inspections of vehicle parts and systems to verify that the vehicle(s) is/are built in accordance with the relevant data contained in the authenticated information package in respect of the relevant EU type-approval certificates;
1.1.5. carry out or arrange to be carried out relevant installation checks in respect of separate technical units where applicable;
1.1.6. carry out or arrange to be carried out necessary checks in respect of the presence of the devices provided for in Annex II to Regulation (EU) No 168/2013;
1.1.7. carry out or arrange to be carried out necessary checks in order to ensure that the requirements regarding gaseous-fuel systems are fulfilled, if applicable.
2.1. The number of vehicles to be submitted shall be sufficient to permit the proper check of the various combinations to be type-approved according to the following criteria:
2.1.1. vehicle type, variants and versions;
2.1.2. vehicle and propulsion family;
2.1.3. transmission;
2.1.4. body style;
2.1.5. number of doors;
2.1.6. number of seating positions.
3.1. Where no approval certificates for any of the relevant regulatory acts are available, the approval authority shall:
3.1.1. arrange for the necessary tests and checks as required by each of the relevant regulatory acts;