1 LIST OF ANNEXES, Regulation (EU) No 168/2013 of the European Parliament and of the Council of 15 January…

In forcesince 20 Feb 2019

Category | Category name | Common classification criteria

L1e-L7e | All L-category vehicles |

(1)

length ≤ 4000 mm or ≤ 3000 mm for a L6e-B vehicle or ≤ 3700 mm for a L7e-C vehicle, and

(2)

width ≤ 2000 mm, or ≤ 1000 mm for a L1e vehicle, or ≤ 1500 mm for a L6e-B or a L7e-C vehicle and

(3)

height ≤ 2500 mm and

Category | Category name | Common classification criteria

L1e | Light two-wheel powered vehicle |

(4)

two wheels and powered by a propulsion as listed under Article 4(3) and

(5)

engine capacity ≤ 50 cm3 if a PI internal combustion engine forms part of the vehicle’s propulsion configuration and

(6)

maximum design vehicle speed ≤ 45 km/h and

(7)

maximum continuous rated or net power (1) ≤ 4000 W and

(8)

maximum masstechnically permissible mass declared by the manufacturer and

Sub-categories | Subcategory name | Supplemental sub-classification criteria

L1e-A | Powered cycle |

(9)

cycles designed to pedal equipped with an auxiliary propulsion with the primary aim to aid pedalling and

(10)

output of auxiliary propulsion is cut off at a vehicle speed ≤ 25 km/h and

(11)

maximum continuous rated or net power (1) ≤ 1000 W and

(12)

a powered three- or four-wheel cycle complying with supplemental specific sub-classification criteria (9) to (11) is classified as being technically equivalent to a two-wheel L1e-A vehicle.

L1e-B | Two-wheel moped |

(9)

any other vehicle of the L1e category that cannot be classified according to the criteria (9) to (12) of a L1e-A vehicle.

Category | Category name | Common classification criteria

L2e | Three-wheel moped |

(4)

three wheels and powered by a propulsion as listed under Article 4(3) and

(5)

engine capacity ≤ 50 cm3 if a PI internal combustion engine or engine capacity ≤ 500 cm3 if a CI combustion engine forms part of the vehicle’s propulsion configuration and

(6)

maximum design vehicle speed ≤ 45 km/h and

(7)

maximum continuous rated or net power (1) ≤ 4000 W and

(8)

mass in running order ≤ 270 kg and

(9)

equipped with a maximum of two seating positions, including the seating position for the driver and

Sub-categories | Subcategory name | Supplemental sub-classification criteria

L2e-P | Three-wheel moped for passenger transport |

(10)

L2e vehicle other than those complying with the specific classification criteria for a L2e-U vehicle.

L2e-U | Three-wheel moped for utility purposes |

(10)

exclusively designed for the carriage of goods with an open or enclosed, virtually even and horizontal loading bed that meets the following criteria:

(a)

lengthloading bedwidthloading bed0,3 Lengthvehiclemaximum Widthvehicle or

(b)

an equivalent loading bed area as defined above in order to install machines and/or equipment and

(c)

designed with a loading bed area which is clearly separated by a rigid partition from the area reserved for the vehicle occupants and

(d)

the loading bed area shall be able to carry a minimum volume represented by a 600 mm cube.

Category | Category name | Common classification criteria

L3e (2) | Two-wheel motorcycle |

(4)

two wheels and powered by propulsion as listed under Article 4(3) and

(5)

maximum masstechnically permissible mass declared by the manufacturer and

(6)

two-wheel vehicle that cannot be classified as category L1e.

Sub-categories | Subcategory name | Supplemental sub-classification criteria

L3e-A1 | Low-performance motorcycle |

(7)

engine capacity ≤ 125 cm3 and

(8)

maximum continuous rated or net power (1) ≤ 11 kW and

(9)

power (1)/weight ratio ≤ 0,1 kW/kg.

L3e-A2 | Medium-performance motorcycle |

(7)

maximum continuous rated or net power (1) ≤ 35 kW and

(8)

power (1)/weight ratio ≤ 0,2 kW/kg and

(9)

not derived from a vehicle equipped with an engine of more than double its power (1) and

(10)

L3e vehicle that cannot be classified under supplemental sub-classification criteria (7), (8) and (9) of a L3e-A1 vehicle.

L3e-A3 | High-performance motorcycle |

(7)

any other L3e vehicle that cannot be classified according to the classification criteria of a L3e-A1 or L3e-A2 vehicle.

Sub-sub-categories | Sub-Subcategory name | Sub-Sub-classification criteria in addition to the sub-classification criteria of L3e-A1, L3e-A2 or L3e-A3 vehicles

L3e-AxE

(x = 1, 2 or 3)

Enduro motorcycles |

(a)

seat height ≥ 900 mm and

(b)

ground clearance ≥ 310 mm and

(c)

overall gear ratio in highest gear (primary gear ratio × secondary gear ratio in the highest speed × final drive ratio) ≥ 6,0 and

(d)

mass in running order plus the mass of the propulsion battery in case of electric or hybrid electric propulsion ≤ 140 kg and

(e)

no seating position for a passenger.

L3e-AxT

(x = 1, 2 or 3)

Trial motorcycles |

(a)

seat height ≤ 700 mm and

(b)

ground clearance ≥ 280 mm and

(c)

fuel tank capacity ≤ 4 litres and

(d)

overall gear ratio in highest gear (primary gear ratio × secondary gear ratio in the highest speed × final drive ratio) ≥ 7,5 and

(e)

mass in running order ≤ 100 kg and

(f)

no seating position for a passenger.

Category | Category name | Common classification criteria

L4e | Two-wheel motorcycle with side-car |

(4)

base powered vehicle complying with the classification and subclassification criteria for a L3e vehicle and

(5)

base powered vehicle equipped with one side-car and

(6)

with a maximum of four seating positions including the driver on the motorcycle with side car and

(7)

a maximum of two seating positions for passengers in the side car and

(8)

maximum masstechnically permissible mass declared by the manufacturer.

Category | Category name | Common classification criteria

L5e | Powered tricycle |

(4)

three wheels and powered by a propulsion as listed under Article 4(3) and

(5)

mass in running order ≤ 1000 kg and

(6)

three-wheel vehicle that cannot be classified as a L2e vehicle and

Sub-categories | Subcategory name | Supplemental sub-classification criteria

L5e-A | Tricycle |

(7)

L5e vehicle other than those complying with the specific classification criteria for a L5e-B vehicle and

(8)

with a maximum of five seating positions, including the seating position of the driver.

L5e-B | Commercial tricycle |

(7)

designed as a utility vehicle and characterised by an enclosed driving and passenger compartment accessible by maximum three sides and

(8)

equipped with a maximum of two seating positions, including the seating position for the driver and

(9)

exclusively designed for the carriage of goods with an open or enclosed, virtually even and horizontal loading bed that meets the following criteria:

(a)

lengthloading bedwidthloading bed0,3LengthvehicleWidthvehicle or

(b)

an equivalent loading bed area as defined above designed to install machines and/or equipment and

(c)

designed with a loading bed area which is clearly separated by a rigid partition from the area reserved for the vehicle occupants and

(d)

the loading bed area shall be able to carry a minimum volume represented by a 600 mm cube.

Category | Category name | Common classification criteria

L6e | Light quadricycle |

(4)

four wheels and powered by a propulsion as listed under Article 4(3) and

(5)

maximum design vehicle speed ≤ 45 km/h and

(6)

the mass in running order ≤ 425 kg and

(7)

engine capacity ≤ 50 cm3 if a PI engine or engine capacity ≤ 500 cm3 if a CI engine forms part of the vehicle’s propulsion configuration and

(8)

equipped with a maximum of two seating positions, including the seating position for the driver and

Sub-categories | Subcategory name | Supplemental sub-classification criteria

L6e-A | Light on-road quad |

(9)

L6e vehicle not complying with the specific classification criteria for a L6e-B vehicle and

(10)

maximum continuous rated or net power (1) ≤ 4000 W.

L6e-B | Light quadri-mobile |

(9)

enclosed driving and passenger compartment accessible by maximum three sides and

(10)

maximum continuous rated or net power (1) ≤ 6000 W and

Sub-sub-categories | Sub-subcategory name | Sub-sub-classification criteria in addition to the sub-classification criteria of a L6e-B vehicle

L6e-BP | Light quadri-mobile for passenger transport |

(11)

L6e-B vehicle mainly designed for passenger transport and

(12)

L6e-B vehicle other than those complying with the specific classification criterion for a L6e-BU vehicle.

L6e-BU | Light quadri-mobile for utility purposes |

(11)

exclusively designed for the carriage of goods with an open or enclosed, virtually even and horizontal loading bed that meets the following criteria:

(a)

lengthloading bedwidthloading bed0,3LengthvehicleWidthvehicle or

(b)

an equivalent loading bed area as defined above in order to install machines and/or equipment and

(c)

designed with a loading bed area which is clearly separated by a rigid partition from the area reserved for the vehicle occupants and

(d)

the loading bed area shall be able to carry a minimum volume represented by a 600 mm cube.

Category | Category name | Common classification criteria

L7e | Heavy quadricycle |

(4)

four wheels and powered by a propulsion as listed under Article 4(3) and

(5)

mass in running order:

(a)

≤ 450 kg for transport of passengers;

(b)

≤ 600 kg for transport of goods.

and

(6)

L7e vehicle that cannot be classified as a L6e vehicle and

Sub-categories | Subcategory name | Supplemental sub-classification criteria

L7e-A | Heavy on-road quad |

(7)

L7e vehicle not complying with the specific classification criteria for a L7e-B or a L7e-C vehicle and

(8)

vehicle designed for the transport of passengers only and

(9)

maximum continuous rated or net power (1) ≤ 15 kW and

Sub-Sub categories | Sub-Sub category name | Supplemental sub-classification criteria

L7e-A1 | A1 heavy on-road quad |

(10)

maximum two straddle seating positions, including the seating position for the rider and

(11)

handlebar to steer.

L7e-A2 | A2 heavy on-road quad |

(10)

L7e-A vehicle not complying with the specific classification criteria for a L7e-A1 vehicle and

(11)

maximum two non-straddle seating positions, including the seating position for the driver.

Sub-category | Subcategory name | Supplemental sub-classification criteria

L7e-B | Heavy all terrain quad |

(7)

L7e vehicle not complying with the specific classification criteria for a L7e-C vehicle and

(8)

ground clearance ≥180 mm and

Sub-Sub categories | Sub-Sub category name | Supplemental sub-classification criteria

L7e-B1 | All terrain quad |

(9)

maximum two straddle seating positions, including the seating position for the rider and

(10)

equipped with a handlebar to steer and

(11)

maximum design vehicle speed ≤ 90 km/h and

(12)

wheelbase to ground clearance ratio ≤ 6.

L7e-B2 | Side-by-side buggy |

(9)

L7e-B vehicle other than a L7e-B1 vehicle and

(10)

maximum three non-straddle seats of which two positioned side-by-side, including the seating position for the driver and

(11)

maximum continuous rated or net power (1) ≤ 15 kW and

(12)

wheelbase to ground clearance ratio ≤ 8.

Sub-category | Subcategory name | Supplemental sub-classification criteria

L7e-C | Heavy quadri-mobile |

(7)

L7e vehicle not complying with the specific classification criteria for a L7e-B vehicle and

(8)

maximum continuous rated or net power (1) ≤ 15 kW and

(9)

maximum design vehicle speed ≤ 90 km/h and

(10)

enclosed driving and passenger compartment accessible via maximum three sides and

Sub-sub-categories | Sub-subcategory name | Sub-sub-classification criteria in addition to the sub-classification criteria of a L7e-C vehicle

L7e-CP | Heavy quadri-mobile for passenger transport |

(11)

L7e-C vehicle not complying with the specific classification criteria for a L7e-CU vehicle and

(12)

maximum four non-straddle seats, including the seating position for the driver.

L7e-CU | Heavy quadri-mobile for utility purposes |

(11)

exclusively designed for the carriage of goods with an open or enclosed, virtually even and horizontal loading bed that meets the following criteria:

(a)

lengthloading bedwidthloading bed0,3 LengthvehicleWidthvehicle or

(b)

an equivalent loading bed area as defined above designed to install machines and/or equipment and

(c)

designed with a loading bed area which is clearly separated by a rigid partition from the area reserved for the vehicle occupants and

(d)

the loading bed area shall be able to carry a minimum volume represented by a 600 mm cube and

(12)

maximum two non-straddle seats, including the seating position for the driver.

NB: refer to the end of Annex VIII for an overview of the notes to the Annexes.

No | Article | Subject | Regulatory act reference | Vehicle Categories

L1e-A | L1e-B | L2e | L3e | L4e | L5e-A | L5e-B | L6e-A | L6e-B | L7e-A | L7e-B | L7e-C

A | ENVIRONMENTAL AND PROPULSION PERFORMANCE REQUIREMENTS

1 | 23 & 24 | environmental test procedures related to exhaust emissions, evaporative emissions, greenhouse gas emissions, fuel consumption and reference fuels | | X | X | X | X | X | X | X | X | X | X | X | X

2 | maximum design vehicle speed, maximum torque, maximum continuous total engine power of propulsion | X | X | X | X | X | X | X | X | X | X | X | X

3 | test procedures related to sound | X | X | X | X | X | X | X | X | X | X | X | X

No | Article | Subject | Regulatory act reference | Vehicle Categories

L1e-A | L1e-B | L2e | L3e | L4e | L5e-A | L5e-B | L6e-A | L6e-B | L7e-A1 | L7e-A2 | L7e-B1 | L7e-B2 | L7e-C

B | VEHICLE FUNCTIONAL SAFETY REQUIREMENTS

1 | 22 | audible warning devices | | | X | X | X | X | X | X | X | X | X | X | X | X | X

2 | braking, including anti-lock and combined brake systems | X | X | X | X | X | X | X | X | X | X | X | X | X | X

3 | electrical safety | X | X | X | X | X | X | X | X | X | X | X | X | X | X

4 | manufacturer declaration requirements regarding endurance testing of functional safety systems, parts and equipment | X | X | X | X | X | X | X | X | X | X | X | X | X | X

5 | front and rear protective structures | | | IF | | | IF | IF | IF | IF | IF | IF | IF | IF | IF

6 | glazing, windscreen wipers and washers, defrosting and demisting devices | | IF | IF | IF | IF | IF | X | IF | X | IF | IF | IF | IF | X

7 | driver-operated controls including identification of controls, tell-tales and indicators | | X | X | X | X | X | X | X | X | X | X | X | X | X

8 | installation of lighting and light signalling devices, including automatic switching-on of lighting | X | X | X | X | X | X | X | X | X | X | X | X | X | X

9 | rearward visibility | | X | X | X | X | X | X | X | X | X | X | X | X | X

10 | rollover protective structure (ROPS) | | | | | | | | | | | | | X |

11 | safety belt anchorages and safety belts | | | IF | | | | X | IF | IF | IF | X | | X | X

12 | seating position (saddles and seats) | X | X | X | X | X | X | X | X | X | X | X | X | X | X

13 | steer-ability, cornering properties and turn-ability | X | X | X | X | X | X | X | X | X | X | X | X | X | X

14 | installation of tyres | X | X | X | X | X | X | X | X | X | X | X | X | X | X

15 | vehicle maximum speed limitation plate and location on vehicle | | | IF | | | | IF | IF | IF | IF | IF | X | X | IF

16 | vehicle occupant protection, including interior fittings, head restraint and vehicle doors | | | IF | | | IF | IF | IF | IF | | IF | | IF | IF

17 | maximum continuous rated or net power and/or vehicle speed limitation by design | X | X | X | IF | IF | | | X | X | X | X | X | X | X

18 | vehicle structure integrity | X | X | X | X | X | X | X | X | X | X | X | X | X | X

No | Article | Subject | Regulatory act reference | Vehicle Categories

L1e-A | L1e-B | L2e | L3e | L4e | L5e-A | L5e-B | L6e-A | L6e-B | L7e-A1 | L7e-A2 | L7e-B1 | L7e-B2 | L7e-C

C1 | VEHICLE CONSTRUCTION AND GENERAL TYPE-APPROVAL REQUIREMENTS

1 | 20 | anti-tampering measures | | X | X | X | X | X | X | X | X | X | X | X | X | X | X

2 | 25 | arrangements for type-approval procedures | X | X | X | X | X | X | X | X | X | X | X | X | X | X

3 | 33 | conformity of production requirements | X | X | X | X | X | X | X | X | X | X | X | X | X | X

4 | 18 | coupling devices and attachments | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF

5 | 18 | devices to prevent unauthorised use | X | X | X | X | X | X | X | X | X | X | X | X | X | X

6 | 18 | electromagnetic compatibility (EMC) | X | X | X | X | X | X | X | X | X | X | X | X | X | X

7 | 18 | external projections | X | X | X | X | X | X | X | X | X | X | X | X | X | X

8 | 18 | fuel storage | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF | IF

9 | 18 | load platforms | | | IF | | | | X | | IF | | | IF | IF | IF

10 | 18 | masses and dimensions | X | X | X | X | X | X | X | X | X | X | X | X | X | X

11 | 21 | on-board diagnostics | | | | X | X | X | X | X | X | X | X | X | X | X

12 | 18 | passenger handholds and footrests | | X | IF | IF | IF | IF | IF | X | | IF | IF | IF | IF |

13 | 18 | registration plate space | X | X | X | X | X | X | X | X | X | X | X | X | X | X

14 | 18 | repair and maintenance information | X | X | X | X | X | X | X | X | X | X | X | X | X | X

15 | 18 | stands | X | X | | X | | | | | | | | | |

C2 | REQUIREMENTS OF TECHNICAL SERVICES

16 | 65 | performance standards and assessment of technical services | |

NB: refer to the end of Annex VIII for an overview of the notes to the Annexes.

Vehicle (Sub-)category | Vehicle (Sub-)category name |

Small series

(units for each type made available on the market, registered and entered into service per year)

L1e-A | Powered cycle | 50

L1e-B | Two-wheel moped

L2e | Three-wheel moped

L3e | Two-wheel motorcycle | 75

L4e | Two-wheel motorcycle with side-car | 150

L5e-A | Tricycle | 75

L5e-B | Commercial tricycle | 150

L6e-A | Light on-road quad | 30

L6e-B | Light quadri-mobile | 150

L7e-A | Heavy on-road quad | 30

L7e-B | Heavy all terrain quad | 50

L7e-C | Heavy quadri-mobile | 150

Point | Description | (Sub-)category | New types of vehicles obligatory | Existing types of vehicles obligatory | Last date of registration of compliant vehicles

1.

| Application of delegated act on environmental and propulsion performance requirements, items as listed in Annex II (A) | | | |

1.1. | Test type I, tailpipe emission test after cold start | — | — | — | —

1.1.1. | Test cycle | — | — | — | —

1.1.1.1. | Test type I, ECE R 47 test cycle | L1e, L2e, L6e | 1.1.2017 | 1.1.2018 | 31.12.2020

1.1.1.2. | Test type I, ECE R 40 (with extra urban driving cycle if applicable) | L5e-B, L7e-B, L7e-C | 1.1.2016 | 1.1.2017 | 31.12.2020

1.1.1.3. | Test type I, WMTC, stage 2 | L3e, L4e, L5e-A, L7e-A | 1.1.2016 | 1.1.2017 | 31.12.2020

1.1.1.4. | Test type I, revised WMTC based test cycle | L1e-L7e | 1.1.2020 | 1.1.2021 |

1.1.2. | Test type I, tailpipe emission limits | | — | — | —

1.1.2.1. | Euro 4: Annex VI A1 | L1e, L2e, L6e | 1.1.2017 | 1.1.2018 | 31.12.2020; for L2e-U and L6e-B: 31.12.2024

1.1.2.2. | Euro 4: Annex VI A1 | L3e, L4e, L5e, L7e | 1.1.2016 | 1.1.2017 | 31.12.2020; for L3e-AxE and L3e-AxT 31.12.2024

1.1.2.3. | Euro 5: Annex VI A2 | L1e-L7e |

1.1.2020;

for L2e-U, L3e-AxE, L3e-AxT and L6e-B: 1.1.2024

1.1.2021;

for L2e-U, L3e-AxE, L3e-AxT and L6e-B: 1.1.2025

1.2. | Test type II, emissions test at (increased) idle/free acceleration | | | |

1.2.1. | Test type II, emissions test at (increased) idle/free acceleration | L1e, L2e, L6e | 1.1.2017 | 1.1.2018 |

1.2.2. | Test type II, emissions test at (increased) idle/free acceleration | L3e, L4e, L5e, L7e | 1.1.2016 | 1.1.2017 |

1.3. | Test type III, zero crankcase gas emissions | | | |

1.3.1. | Test type III, zero crankcase gas emissions | L1e, L2e, L6e | 1.1.2017 | 1.1.2018 |

1.3.2. | Test type III, zero crankcase gas emissions | L3e, L4e, L5e, L7e | 1.1.2016 | 1.1.2017 |

1.4. | Test type IV, evaporative emissions | | — | — | —

1.4.1. | Fuel tank permeability test | L1e, L2e, L6e | 1.1.2017 | 1.1.2017 |

1.4.2. | Fuel tank permeability test | L3e, L4e, L5e, L7e | 1.1.2016 | 1.1.2016 |

1.4.3. | SHED test procedure | L3e, L4e, L5e-A, L7e-A | 1.1.2016 | 1.1.2017 |

1.4.4. | SHED test procedure | L6e-A | 1.1.2017 | 1.1.2018 |

1.4.5. | SHED test limits, Annex VI (C1) | L3e, L4e, L5e-A, L7e-A | 1.1.2016 | 1.1.2017 | 31.12.2020

1.4.6. | SHED test limits, Annex VI (C1) | L6e-A | 1.1.2017 | 1.1.2018 | 31.12.2020

1.4.7. | SHED test or fuel permeation test, pending study results referred to in Article 23(4) and (5) | L1e-A, L1e-B, L2e, L5e-B, L6e-B, L7e-B, L7e-C | 1.1.2020 | 1.1.2021 |

1.4.8. | SHED test limits, Annex VI (C2), pending study results referred to in Article 23(4) and (5) | L1e-L7e | 1.1.2020 | 1.1.2021 |

1.5. | Test type V, durability testing (3) | | | |

1.5.1. | Euro 4 durability mileage, Annexes VII (A) and (B) | L1e, L2e, L6e | 1.1.2017 | 1.1.2018 | 31.12.2020

1.5.2. | Euro 4 durability mileage, Annexes VII (A) and (B) | L3e, L4e, L5e, L7e | 1.1.2016 | 1.1.2017 | 31.12.2020

1.5.3. | Euro 5, durability mileage, Annexes VII (A) and (B) | L1e-L7e | 1.1.2020 | 1.1.2021 |

1.6. | A test type VI has not been attributed | — | — | — | —

1.7. | Test type VII, greenhouse gas emissions/fuel or energy consumption determination and reporting | | | — |

1.7.1. | Test type VII, greenhouse gas emissions/fuel or energy consumption determination and reporting | L1e, L2e, L6e | 1.1.2017 | 1.1.2018 |

1.7.2. | Test type VII, greenhouse gas emissions/fuel or energy consumption determination and reporting | L3e, L4e, L5e, L7e | 1.1.2016 | 1.1.2017 |

1.8. | Test type VIII, OBD environmental test | | — | — |

1.8.1. | OBD stage I functional requirements | L3e, L4e, L5e-A, L7e-A | 1.1.2016 | 1.1.2017 | 31.12.2020

OBD stage I environmental test procedure (test type VIII)

OBD stage I environmental test thresholds, Annex VI (B1)

1.8.2. | OBD stage I functional requirements including any operating mode which significantly reduces engine torque | L3e, L4e, L5e, L7e | 1.1.2020 | 1.1.2021 | 31.12.2024

OBD stage I environmental test procedure (test type VIII)

OBD stage I environmental test thresholds, Annex VI (B1)

1.8.3. | OBD stage I functional requirements including any operating mode which significantly reduces engine torque | L3e, L4e, L5e, L7e | 1.1.2024 | 1.1.2025 |

OBD stage I environmental test procedure (test type VIII)

OBD stage I environmental test thresholds, Annex VI (B2)

1.8.4. | OBD stage II functional requirements with the exception of catalyst monitoring | L3e (except L3e-AxE and L3e-AxT), L4e, L5e-A, L7e-A | 1.1.2020 | 1.1.2021 | 31.12.2024

OBD stage II environmental test procedures (test type VIII)

OBD stage II environmental test thresholds, Annex VI (B1)

1.8.5. | OBD stage II functional requirements, | L3e (except L3e-AxE and L3e-AxT), L4e, L5e-A, L7e-A | 1.1.2024 | 1.1.2025 |

OBD stage II environmental test procedures (test type VIII),

OBD stage II environmental test thresholds, Annex VI (B2)

1.9. | Test type IX, sound level (3) | | | |

1.9.1. | Sound level test procedure and limit values Annex VI (D) | L1e, L2e, L6e | 1.1.2017 | 1.1.2018 |

1.9.2. | Sound level test procedure and limit values (3), Annex VI (D) | L3e, L4e, L5e, L7e | 1.1.2016 | 1.1.2017 |

This article is long: the rest is at the official publication.