For the purpose of this Part, the competent authority shall be the authority designated by the Member State where a person applies for the issue of a cabin crew attestation.
This Part establishes the requirements for the issue of cabin crew attestations and the conditions for their validity and use by their holders.
The application for a cabin crew attestation shall be made in a form and manner established by the competent authority.
The applicant for a cabin crew attestation shall be at least 18 years of age.
The privileges of holders of a cabin crew attestation are to act as cabin crew members in commercial air transport operation of aircraft referred to in Article 4(1)(b) and (c) of Regulation (EC) No 216/2008.
Cabin crew members may exercise the privileges specified in (a) only if they:
hold a valid cabin crew attestation as specified in CC.CCA.105; and
comply with CC.GEN.030, CC.TRA.225 and the applicable requirements of Part-MED.
To show compliance with the applicable requirements as specified in CC.GEN.025(b), each holder shall keep, and provide upon request, the cabin crew attestation, the list and the training and checking records of his/her aircraft type or variant qualification(s), unless the operator employing his/her services keeps such records and can make them readily available upon request by a competent authority or by the holder.
Cabin crew attestations shall only be issued to applicants who have passed the examination following completion of the initial training course in accordance with this Part.
Cabin crew attestations shall be issued:
by the competent authority; and/or
by an organisation approved to do so by the competent authority.
The cabin crew attestation shall be issued with unlimited duration and shall remain valid unless:
it is suspended or revoked by the competent authority; or
its holder has not exercised the associated privileges during the preceding 60 months on at least one aircraft type.
If holders do not comply with this Part, their cabin crew attestation may be suspended or revoked by the competent authority.
In case of suspension or revocation of their cabin crew attestation by the competent authority, holders shall:
be informed in writing of this decision, and of their right of appeal in accordance with national law;
not exercise the privileges granted by their cabin crew attestation;
inform, without undue delay, the operator(s) employing their services; and
return their attestation in accordance with the applicable procedure established by the competent authority.
Training required in this Part shall be:
provided by training organisations or commercial air transport operators approved to do so by the competent authority;
performed by personnel suitably experienced and qualified for the training elements to be covered; and
conducted according to a training programme and syllabus documented in the organisation's approval.
Applicants for a cabin crew attestation shall complete an initial training course to familiarise themselves with the aviation environment and to acquire sufficient general knowledge and basic proficiency required to perform the duties and discharge the responsibilities related to the safety of passengers and flight during normal, abnormal and emergency operations.
The programme of the initial training course shall cover at least the elements specified in Appendix 1 to this Part. It shall include theoretical and practical training.
Applicants for a cabin crew attestation shall undergo an examination covering all elements of the training programme specified in (b), except CRM training, to demonstrate that they have attained the level of knowledge and proficiency required in (a).
Holders of a valid cabin crew attestation shall only operate on an aircraft if they are qualified in accordance with the applicable requirements of Part-ORO.
To be qualified for an aircraft type or a variant, the holder:
shall comply with the applicable training, checking and validity requirements, covering as relevant to the aircraft to be operated:
aircraft-type specific training, operator conversion training and familiarisation;
differences training;
recurrent training; and
shall have operated within the preceding 6 months on the aircraft type, or shall have completed the relevant refresher training and checking before operating again on that aircraft type.
The training programme of the initial training course shall include at least the following:
1.1. aviation terminology, theory of flight, passenger distribution, areas of operation, meteorology and effects of aircraft surface contamination;
1.2. aviation regulations relevant to cabin crew and the role of the competent authority;
1.3. duties and responsibilities of cabin crew during operations and the need to respond promptly and effectively to emergency situations;
1.4. continuing competence and fitness to operate as a cabin crew member, including as regards flight and duty time limitations and rest requirements;
1.5. the importance of ensuring that relevant documents and manuals are kept up-to-date, with amendments provided by the operator as applicable;
1.6. the importance of cabin crew performing their duties in accordance with the operations manual of the operator;
1.7. the importance of the cabin crew’s pre-flight briefing and the provision of necessary safety information with regards to their specific duties; and
1.8. the importance of identifying when cabin crew members have the authority and responsibility to initiate an evacuation and other emergency procedures.
During training, emphasis shall be placed on the importance of effective communication between cabin crew and flight crew, including communication techniques, common language and terminology.
This course shall be conducted by at least one cabin crew CRM instructor. The training elements shall be covered in depth and shall include at least the following:
3.1. General: human factors in aviation, general instructions on CRM principles and objectives, human performance and limitations;
3.2. Relevant to the individual cabin crew member: personality awareness, human error and reliability, attitudes and behaviours, self-assessment; stress and stress management; fatigue and vigilance; assertiveness; situation awareness, information acquisition and processing.
4.1. the importance of correct seat allocation with reference to aeroplane mass and balance, special categories of passengers and the necessity of seating able-bodied passengers adjacent to unsupervised exits;
4.2. rules covering the safe stowage of cabin baggage and cabin service items and the risk of it becoming a hazard to occupants of the passenger compartment or otherwise obstruction or damaging emergency equipment or exits;
4.3. advice on the recognition and management of passengers who are, or become, intoxicated with alcohol or are under the influence of drugs or are aggressive;
4.4. precautions to be taken when live animals are carried in the passenger compartment;
4.5. duties to be undertaken in the event of turbulence, including securing the passenger compartment; and
4.6. methods used to motivate passengers and the crowd control necessary to expedite an emergency evacuation.
5.1. general instruction on aero-medical aspects and survival;
5.2. the physiological effects of flying with particular emphasis on hypoxia, oxygen requirements, Eustachian tubal function and barotraumas;
5.3. basic first-aid, including care of:
air sickness;
gastro-intestinal disturbances;
hyperventilation;
burns;
wounds;
the unconscious; and
fractures and soft tissue injuries;
5.4. in-flight medical emergencies and associated first-aid covering at least:
asthma;
stress and allergic reactions;
shock;
diabetes;
choking;
epilepsy;
childbirth;
stroke; and
heart attack;
5.5. the use of appropriate equipment including first-aid oxygen, first-aid kits and emergency medical kits and their contents;
5.6. practical cardio-pulmonary resuscitation training by each cabin crew member using a specifically designed dummy and taking account of the characteristics of an aircraft environment; and
5.7. travel health and hygiene, including:
hygiene on board;
risk of contact with infectious diseases and means to reduce such risks;
handling of clinical waste;
aircraft disinsection;
handling of death on board; and
alertness management, physiological effects of fatigue, sleep physiology, circadian rhythm and time zone changes.
8.1. emphasis on the responsibility of cabin crew to deal promptly with emergencies involving fire and smoke and, in particular, emphasis on the importance of identifying the actual source of the fire;
8.2. the importance of informing the flight crew immediately, as well as the specific actions necessary for coordination and assistance, when fire or smoke is discovered;
8.3. the necessity for frequent checking of potential fire-risk areas including toilets, and the associated smoke detectors;
8.4. the classification of fires and the appropriate type of extinguishing agents and procedures for particular fire situations;
8.5. the techniques of application of extinguishing agents, the consequences of misapplication, and of use in a confined space including practical training in fire-fighting and in the donning and use of smoke protection equipment used in aviation; and
8.6. the general procedures of ground-based emergency services at aerodromes.
9.1. principles of survival in hostile environments (e.g. polar, desert, jungle, sea); and
9.2. water survival training which shall include the actual donning and use of personal flotation equipment in water and the use of slide-rafts or similar equipment, as well as actual practice in water.
For the purposes of this Part and of Part-ORA, the following definitions apply:
“Acceptable Means of Compliance (AMC)” are non-binding standards adopted by the Agency to illustrate means to establish compliance with the Basic Regulation and its Implementing Rules;
“Alternative means of compliance” are those that propose an alternative to an existing AMC or those that propose new means to establish compliance with Regulation (EC) No 216/2008 and its Implementing Rules for which no associated AMC have been adopted by the Agency;
“Approved training organisation (ATO)” means an organisation qualified for the issue or continuation of an approval to provide training for pilot licences and associated ratings and certificates;
“Basic instrument training device model (BITD model)” means a defined hardware and software combination, which has obtained a BITD qualification;
“Certification specifications (CS)” are technical standards adopted by the Agency indicating means to show compliance with the Basic Regulation and its Implementing Rules and which can be used by organisation for the purpose of certification;
“Flight instructor (FI)” means an instructor with the privileges to provide training in an aircraft, in accordance with Part-FCL;
“Flight simulation training device (FSTD)” means a training device which is:
in the case of aeroplanes, a full flight simulator (FFS), a flight training device (FTD), a flight and navigation procedures trainer (FNPT), or a basic instrument training device (BITD);
in the case of helicopters, a full flight simulator (FFS), a flight training device (FTD) or a flight and navigation procedures trainer (FNPT);
“FSTD qualification” means the level of technical ability of an FSTD as defined in the compliance document;
“FSTD user” means the organisation or person requesting training, checking or testing through the use of an FSTD to an ATO;
“Grounding” means the formal prohibition of an aircraft to take-off and the taking of such steps as are necessary to detain it;
“Guidance Material (GM)” means non-binding material developed by the Agency that helps to illustrate the meaning of a requirement or specification and is used to support the interpretation of the Basic Regulation, its Implementing Rules and AMC;
“ARO.RAMP” means the Subpart RAMP of Annex II to the Regulation on Air Operations;
“Other training device (OTD)” means an aid used for pilot training other than an FSTD that provides for training where a complete flight deck or cockpit environment is not necessary;
“Part-ARA” means Annex VI to the Regulation on Civil Aviation Aircrew;
“Part-ORO” means Annex III to the Regulation on Air Operations;
“Part-CC” means Annex V to the Regulation on Civil Aviation Aircrew;
“Part-FCL” means Annex I to the Regulation on Civil Aviation Aircrew;
“Part-MED” means Annex IV to the Regulation on Civil Aviation Aircrew;
“Part-ORA” means Annex VII to the Regulation on Civil Aviation Aircrew;
“Principal place of business” means the head office or registered office of the organisation within which the principal financial functions and operational control of the activities referred to in this Regulation are exercised;
“Qualification test guide (QTG)” means a document designed to demonstrate that the performance and handling qualities of an FSTD represent those of the aircraft, class of aeroplane or type of helicopter, simulated within prescribed limits and that all applicable requirements have been met. The QTG includes both the data of the aircraft, class of aeroplane or type of helicopter and FSTD data used to support the validation.
The competent authority shall provide all legislative acts, standards, rules, technical publications and related documents to relevant personnel in order to allow them to perform their tasks and to discharge their responsibilities.
The Agency shall develop Acceptable Means of Compliance (AMC) that may be used to establish compliance with Regulation (EC) No 216/2008 and its Implementing Rules. When the AMC are complied with, the related requirements of the Implementing Rules are met.
Alternative means of compliance may be used to establish compliance with the Implementing Rules.
The competent authority shall establish a system to consistently evaluate that all alternative means of compliance used by itself or by organisations and persons under its oversight allow the establishment of compliance with Regulation (EC) No 216/2008 and its Implementing Rules.
The competent authority shall evaluate all alternative means of compliance proposed by an organisation in accordance with ORA.GEN.120 by analysing the documentation provided and, if considered necessary, conducting an inspection of the organisation.
When the competent authority finds that the alternative means of compliance are in accordance with the Implementing Rules, it shall without undue delay:
notify the applicant that the alternative means of compliance may be implemented and, if applicable, amend the approval or certificate of the applicant accordingly; and
notify the Agency of their content, including copies of all relevant documentation;
inform other MS about alternative means of compliance that were accepted.
When the competent authority itself uses alternative means of compliance to achieve compliance with Regulation (EC) No 216/2008 and its Implementing Rules it shall:
make them available to all organisations and persons under its oversight; and
without undue delay notify the Agency.
The competent authority shall provide the Agency with a full description of the alternative means of compliance, including any revisions to procedures that may be relevant, as well as an assessment demonstrating that the Implementing Rules are met.
The competent authority shall without undue delay notify the Agency in case of any significant problems with the implementation of Regulation (EC) No 216/2008 and its Implementing Rules.
The competent authority shall provide the Agency with safety-significant information stemming from the occurrence reports it has received.
Without prejudice to Directive 2003/42/EC of the European Parliament and of the Council [OJ L 167, 4.7.2003, p. 23.] the competent authority shall implement a system to appropriately collect, analyse and disseminate safety information.
The Agency shall implement a system to appropriately analyse any relevant safety information received and without undue delay provide to Member States and the Commission any information, including recommendations or corrective actions to be taken, necessary for them to react in a timely manner to a safety problem involving products, parts, appliances, persons or organisations subject to Regulation (EC) No 216/2008 and its Implementing Rules.
Upon receiving the information referred to in (a) and (b), the competent authority shall take adequate measures to address the safety problem.
Measures taken under (c) shall immediately be notified to all persons or organisations which need to comply with them under Regulation (EC) No 216/2008 and its Implementing Rules. The competent authority shall also notify those measures to the Agency and, when combined action is required, the other Member States concerned.
The competent authority shall establish and maintain a management system, including as a minimum:
documented policies and procedures to describe its organisation, means and methods to achieve compliance with Regulation (EC) No 216/2008 and its Implementing Rules. The procedures shall be kept up-to-date and serve as the basic working documents within that competent authority for all related tasks;
a sufficient number of personnel to perform its tasks and discharge its responsibilities. Such personnel shall be qualified to perform their allocated tasks and have the necessary knowledge, experience, initial and recurrent training to ensure continuing competence. A system shall be in place to plan the availability of personnel, in order to ensure the proper completion of all tasks;
adequate facilities and office accommodation to perform the allocated tasks;
a function to monitor compliance of the management system with the relevant requirements and adequacy of the procedures including the establishment of an internal audit process and a safety risk management process. Compliance monitoring shall include a feedback system of audit findings to the senior management of the competent authority to ensure implementation of corrective actions as necessary; and
a person or group of persons, ultimately responsible to the senior management of the competent authority for the compliance monitoring function.
The competent authority shall, for each field of activity including management system, appoint one or more persons with the overall responsibility for the management of the relevant task(s).
The competent authority shall establish procedures for participation in a mutual exchange of all necessary information and assistance with other competent authorities concerned including on all findings raised and follow-up actions taken as a result of oversight of persons and organisations exercising activities in the territory of a Member State, but certified by the competent authority of another Member State or the Agency.
A copy of the procedures related to the management system and their amendments shall be made available to the Agency for the purpose of standardisation.
Tasks related to the initial certification or continuing oversight of persons or organisations subject to Regulation (EC) No 216/2008 and its Implementing Rules shall be allocated by Member States only to qualified entities. When allocating tasks, the competent authority shall ensure that it has:
a system in place to initially and continuously assess that the qualified entity complies with Annex V to Regulation (EC) No 216/2008.
This system and the results of the assessments shall be documented;
established a documented agreement with a the qualified entity, approved by both parties at the appropriate management level, which clearly defines:
the tasks to be performed;
the declarations, reports and records to be provided;
the technical conditions to be met in performing such tasks;
the related liability coverage; and
the protection given to information acquired in carrying out such tasks.
The competent authority shall ensure that the internal audit process and a safety risk management process required by ARA.GEN.200(a)(4) cover all certification or continuing oversight tasks performed on its behalf.
The competent authority shall have a system in place to identify changes that affect its capability to perform its tasks and discharge its responsibilities as defined in Regulation (EC) No 216/2008 and its Implementing Rules. This system shall enable it to take action as appropriate to ensure that its management system remains adequate and effective.
The competent authority shall update its management system to reflect any change to Regulation (EC) No 216/2008 and its Implementing Rules in a timely manner, so as to ensure effective implementation.
The competent authority shall notify the Agency of changes affecting its capability to perform its tasks and discharge its responsibilities as defined in Regulation (EC) No 216/2008 and its Implementing Rules.
The competent authority shall establish a system of record-keeping providing for adequate storage, accessibility and reliable traceability of:
the management system’s documented policies and procedures;
training, qualification and authorisation of its personnel;
the allocation of tasks, covering the elements required by ARA.GEN.205 as well as the details of tasks allocated;
certification processes and continuing oversight of certified organisations;
processes for issuing personnel licences, ratings, certificates and attestations and for the continuing oversight of the holders of those licences, ratings, certificates and attestations;
processes for issuing FSTD qualification certificates and for the continuing oversight of the FSTD and of the organisation operating it;
oversight of persons and organisations exercising activities within the territory of the Member State, but overseen or certified by the competent authority of another Member State or the Agency, as agreed between these authorities;
the evaluation and notification to the Agency of alternative means of compliance proposed by organisations and the assessment of alternative means of compliance used by the competent authority itself;
findings, corrective actions and date of action closure;
enforcement measures taken;
safety information and follow-up measures; and
the use of flexibility provisions in accordance with Article 14 of Regulation (EC) No 216/2008.