1 ANNEX, Commission Regulation (EU) No 231/2012 of 9 March 2012 laying down specifications for fo…

In forcesince 8 Nov 2026

Ethylene oxide may not be used for sterilising purposes in food additives.

No residue above 0,1 mg/kg, irrespective of its origin, of ethylene oxide (sum of ethylene oxide and 2-chloro-ethanol expressed as ethylene oxide [i.e. ethylene oxide + 0,55* 2-chloroethanol.]) shall be present in food additives listed in Annexes II and III to Regulation (EC) No 1333/2008, including mixtures of food additives.

Aluminium lakes for use in colours only where explicitly stated.

Definition: | Aluminium lakes are prepared by reacting colours complying with the purity criteria set out in the appropriate specification monograph with alumina under aqueous conditions. The alumina is usually freshly prepared undried material made by reacting aluminium sulphate or chloride with sodium or calcium carbonate or bicarbonate or ammonia. Following lake formation, the product is filtered, washed with water and dried. Unreacted alumina may also be present in the finished product.

HCl insoluble matter | Not more than 0,5 %

ΝaΟΗ insoluble matter | Νot more than 0,5 %, for Ε 127 erythrosine only

Ether extractable matter |

Not more than 0,2 % (under neutral conditions)

Specific purity criteria for the corresponding colours are applicable.

Synonyms | CI Natural Yellow 3; Turmeric Yellow; Diferoyl Methane

Definition |

Curcumin is obtained by solvent extraction of turmeric i.e. the ground rhizomes of strains of Curcuma longa L. In order to obtain a concentrated curcumin powder, the extract is purified by crystallization. The product consists essentially of curcumins; i.e. the colouring principle (1,7-bis(4-hydroxy-3-methoxyphenyl)hepta-1,6-dien-3,5-dione) and its two desmethoxy derivatives in varying proportions. Minor amounts of oils and resins naturally occurring in turmeric may be present.

Curcumin is also used as the aluminium lake; the aluminium content is less than 30 %.

Only the following solvents may be used in the extraction: ethylacetate, acetone, carbon dioxide, dichloromethane, n-butanol, methanol, ethanol, hexane, propan-2-ol.

Colour Index No | 75300

Einecs | 207-280-5

Chemical name |

I 1,7-Bis(4-hydroxy-3-methoxyphenyl)hepta-1,6-diene-3,5-dione

II 1-(4-Hydroxyphenyl)-7-(4-hydroxy-3-methoxy-phenyl-)hepta-1,6-diene-3,5-dione

III 1,7-Bis(4-hydroxyphenyl)hepta-1,6-diene-3,5-dione

Chemical formula |

I C21H20O6

II C20H18O5

III C19H16O4

Molecular weight |

I.

368,39

II.

338,39

III.

308,39

Assay |

Content not less than 90 % total colouring matters

E1cm1%1607 at ca. 426 nm in ethanol

Description | Orange-yellow crystalline powder

Identification

Spectrometry | Maximum in ethanol at ca. 426 nm

Melting range | 179 °C-182 °C

Purity

Solvent residues | Ethylacetate | Not more than 50 mg/kg, singly or in combination

Acetone

n-butanol

Methanol

Ethanol

Hexane

Propan-2-ol

Dichloromethane: not more than 10 mg/kg

Arsenic | Not more than 3 mg/kg

Lead | Not more than 10 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | Lactoflavin;

Definition

Colour Index No |

Einecs | 201-507-1

Chemical name | 7,8-Dimethyl-10-(D-ribo-2,3,4,5-tetrahydroxypentyl)benzo(g)pteridine-2,4(3H,10H)-dione; 7,8-dimethyl-10-(1′-D-ribityl)isoalloxazine

Chemical formula | C17H20N4O6

Molecular weight | 376,37

Assay |

Content not less than 98 % on the anhydrous basis

E1cm1% 328 at ca. 444 nm in aqueous solution

Description | Yellow to orange-yellow crystalline powder, with slight odour

Identification

Spectrometry | The ratio A375/A267 is between 0,31 and 0,33 | in aqueous solution

The ratio A444/A267 is between 0,36 and 0,39

Maximum in water at ca. 375 nm

Specific rotation | [α]D20 between – 115° and – 140° in a 0,05 N sodium hydroxide solution

Purity

Loss on drying | Not more than 1,5 % (105 °C, 4 hours)

Sulphated ash | Not more than 0,1 %

Primary aromatic amines | Not more than 100 mg/kg (calculated as aniline)

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | Riboflavin-5′-phosphate sodium

Definition | These specifications apply to riboflavin 5′-phosphate together with minor amounts of free riboflavin and riboflavin diphosphate.

Colour Index No |

Einecs | 204-988-6

Chemical name | Monosodium(2R,3R,4S)-5-(3′)10′-dihydro-7′,8′-dimethyl-2′,4′-dioxo-10′-benzo[γ]pteridinyl)-2,3,4-trihydroxypentyl phosphate; monosodium salt of 5′-monophosphate ester of riboflavin

Chemical formula | For the dihydrate form: C17H20N4NaO9P · 2H2O

For the anhydrous form: C17H20N4NaO9P

Molecular weight | 514,36

Assay |

Content not less than 95 % total colouring matters calculated as C17H20N4NaO9P.2H2O

E1cm1% 250 at ca. 375 nm in aqueous solution

Description | Yellow to orange crystalline hygroscopic powder, with slight odour

Identification

Spectrometry | The ratio A375/A267 is between 0,30 and 0,34 | in aqueous solution

The ratio A444/A267 is between 0,35 and 0,40

Maximum in water at ca. 375 nm

Specific rotation | [α]D20 between + 38° and + 42° in a 5 molar HCl solution

Purity

Loss on drying | Not more than 8 % (100 °C, 5 hours in vacuum over P2O5) for the dihydrate form

Sulphated ash | Not more than 25 %

Inorganic phosphate | Not more than 1,0 % (calculated as PO4 on the anhydrous basis)

Subsidiary colouring matters |

Riboflavin (free): Not more than 6 %

Riboflavine diphosphate: Not more than 6 %

Primary aromatic amines | Not more than 70 mg/kg (calculated as aniline)

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Food Yellow 4

Definition |

Tartrazine is prepared from 4-amino-benzenesulphonic acid, which is diazotized using hydrochloric acid and sodium nitrite. The diazo compound is then coupled with 4,5-dihydro-5-oxo-1-(4sulphophenyl)-1H-pyrazole-3-carboxylic acid or with the methyl ester, the ethyl ester, or a salt of this carboxylic acid. The resulting dye is purified and isolated as the sodium salt. Tartrazine consists essentially of trisodium 5-hydroxy-1-(4-sulfonatophenyl)-4-(4-sulfonatophenylazo)-H-pyrazole-3-carboxylate and subsidiary colouring matters together with sodium chloride and/or sodium sulphate as the principal uncoloured components.

Tartrazine is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 19140

Einecs | 217-699-5

Chemical name | Trisodium-5-hydroxy-1-(4-sulfonatophenyl)-4-(4-sulfonatophenylazo)-H-pyrazole-3-carboxylate

Chemical formula | C16H9N4Na3O9S2

Molecular weight | 534,37

Assay |

Content not less than 85 % total colouring matters calculated as the sodium salt

E1cm1% 530 at ca. 426 nm in aqueous solution

Description | Light orange powder or granules

Appearance of the aqueous solution | Yellow

Identification

Spectrometry | Maximum in water at ca. 426 nm

Purity

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters | Not more than 1,0 %

Organic compounds other than colouring matters: |

4-hydrazinobenzene sulfonic acid | Total not more than 0,5 %

4-aminobenzene-1-sulfonic acid

5-oxo-1-(4-sulfophenyl)-2-pyrazoline-3-carboxylic acid

4,4′-diazoaminodi(benzene sulfonic acid)

Tetrahydroxysuccinic acid

Unsulfonated primary aromatic amines | Not more than 0,01 % (calculated as aniline)

Ether extractable matter | Not more than 0,2 % under neutral conditions

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Food Yellow 13

Definition |

Quinoline Yellow is prepared by sulfonating 2-(2-quinolyl) indan-1,3-dione or a mixture containing about two thirds 2-(2-quinolyl)indane-1,3-dione and one third 2-(2-(6-methylquinolyl))indane-1,3-dione. Quinoline Yellow consists essentially of sodium salts of a mixture of disulfonates (principally), monosulfonates and trisulfonates of the above compound and subsidiary colouring matters together with sodium chloride and/or sodium sulphate as the principal uncoloured components.

Quinoline Yellow is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 47005

Einecs | 305-897-5

Chemical name | The disodium salts of the disulfonates of 2-(2-quinolyl) indan-1,3-dione (principal component)

Chemical formula | C18H9N Na2O8S2 (principal component)

Molecular weight | 477,38 (principal component)

Assay |

Content not less than 70 % total colouring matters calculated as the sodium salt

Quinoline Yellow shall have the following composition:

Of the total colouring matters present:

not less than 80 % shall be disodium 2-(2-quinolyl) indan-1,3-dione-disulfonates

not more than 15 % shall be sodium 2-(2-quinolyl) indan-1,3-dione-monosulfonates

not more than 7,0 % shall be trisodium 2-(2-quinolyl) indan-1,3-dione-trisulfonate

E1cm1% 865 (principal component) at ca. 411 nm in aqueous acetic acid solution

Description | Yellow powder or granules

Appearance of the aqueous solution | Yellow

Identification

Spectrometry | Maximum in aqueous acetic acid solution of pH 5 at ca. 411 nm

Purity

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters | Not more than 4,0 %

Organic compounds other than colouring matters: |

2-methylquinoline | Total not more than 0,5 %

2-methylquinoline-sulfonic acid

Phthalic acid

2,6-dimethyl quinoline

2,6-dimethyl quinoline sulfonic acid

2-(2-quinolyl)indan-1,3-dione | Not more than 4 mg/kg

Unsulfonated primary aromatic amines | Not more than 0,01 % (calculated as aniline)

Ether extractable matter | Not more than 0,2 % under neutral conditions

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Food Yellow 3; Orange Yellow S

Definition |

Sunset Yellow FCF consists essentially of disodium 2-hydroxy-1-(4-sulfonatophenylazo) naphthalene-6-sulfonate and subsidiary colouring matters together with sodium chloride and/or sodium sulphate as the principal uncoloured components. Sunset Yellow FCF is manufactured by diazotizing 4-aminobenzenesulphonic acid using hydrochloric acid and sodium nitrite or sulphuric acid and sodium nitrite. The diazo compound is coupled with 6-hydroxy-2-naphthalene-sulphonic acid. The dye is isolated as the sodium salt and dried.

Sunset Yellow FCF is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 15985

Einecs | 220-491-7

Chemical name | Disodium 2-hydroxy-1-(4-sulfonatophenylazo)naphthalene-6-sulfonate

Chemical formula | C16H10N2Na2O7S2

Molecular weight | 452,37

Assay |

Content not less than 85 % total colouring matters calculated as the sodium salt

E1cm1% 555 at ca. 485 nm in aqueous solution at pH 7

Description | Orange-red powder or granules

Appearance of the aqueous solution | Orange

Identification

Spectrometry | Maximum in water at ca. 485 nm at pH 7

Purity

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters | Not more than 5,0 %

1-(Phenylazo)-2-naphthalenol (Sudan I) | Not more than 0,5 mg/kg

Organic compounds other than colouring matters: |

4-aminobenzene-1-sulfonic acid | Total not more than 0,5 %

3-hydroxynaphthalene-2,7-disulfonic acid

6-hydroxynaphthalene-2-sulfonic acid

7-hydroxynaphthalene-1,3-disulfonic acid

4,4′-diazoaminodi(benzene sulfonic acid)

6,6′-oxydi(naphthalene-2-sulfonic acid)

Unsulfonated primary aromatic amines | Not more than 0,01 % (calculated as aniline)

Ether extractable matter | Not more than 0,2 % under neutral conditions

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Natural Red 4

Definition |

Carminic acid is obtained from aqueous, aqueous alcoholic or alcoholic extracts from Cochineal, which consists of the dried bodies of the female insect Dactylopius coccus Costa.

Carmines are aluminium lakes of carminic acid in which aluminium and carminic acid are thought to be present in the molar ratio 1:2.

The colouring principle is carminic acid. Minor amounts of its aminated form 4-aminocarminic acid may also be present.

In commercial products the colouring principle carminic acid may be present in association with ammonium, calcium, potassium or sodium cations, singly or in combination, and these cations may also be present in excess. Commercial products may also contain proteinaceous material derived from the source insect.

Colour Index No | 75470

Einecs | Carminic acid: 215-023-3; carmines: 215-724-4

Chemical name | 7-β-D-glucopyranosyl-3,5,6,8-tetrahydroxy-1-methyl-9,10-dioxoanthracene-2-carboxylic acid (carminic acid); carmine is the hydrated aluminium chelate of this acid

Chemical formula | C22H20O13 (carminic acid)

Molecular weight | 492,39 (carminic acid)

Assay | Content not less than 90 % carminic acid; not less than 50 % carminic acid in the chelates.

Description | Red to dark red, friable, solid or powder

Identification |

Spectrometry |

Carminic acid:

Maximum in aqueous ammonia solution at ca. 518 nm

Maximum in dilute hydrochloric solution at ca. 494 nm

E 1 %/1 cm 139 at peak around 494 nm in dilute hydrochloric acid

4-aminocarminic acid:

Maximum in aqueous ammonia solution at 535 nm

Maximum in dilute hydrochloric solution at 530 nm

E 1 %/1 cm 260 at peak around 535 nm in aqueous ammonia solution, pH 9,5

In commercial products carminic acid may be differentiated from its amine by HPLC

Purity |

Solvent residues |

Ethanol:

Methanol:

Not more than 150 mg/kg

Not more than 50 mg/kg

Total ash |

Carminic acid:

Carmine:

Not more than 5 %

Not more than 12 %

Protein (N × 6,25) |

Carminic acid:

Carmine:

Not more than 2,2 %

Not more than 25 %

4-aminocarminic acid | Not more than 3 % relative to carminic acid

Matter insoluble in dilute ammonia | Carmine: Not more than 1 %

Arsenic | Not more than 1 mg/kg

Lead | Not more than 1,5 mg/kg

Mercury | Not more than 0,5 mg/kg

Cadmium | Not more than 0,1 mg/kg

Microbiological criteria |

Salmonella spp. | Absent in 10 g

Aluminium lakes of this colour may be used.

Synonyms | CI Food Red 3

Definition |

Azorubine consists essentially of disodium 4-hydroxy-3-(4-sulfonato-1-naphthylazo) naphthalene-1-sulfonate and subsidiary colouring matters together with sodium chloride and/or sodium sulphate as the principal uncoloured components.

Azorubine is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 14720

Einecs | 222-657-4

Chemical name | Disodium 4-hydroxy-3-(4-sulfonato-1-naphthylazo) naphthalene-1-sulfonate

Chemical formula | C20H12N2Na2O7S2

Molecular weight | 502,44

Assay |

Content not less than 85 % total colouring matters, calculated as the sodium salt

E1cm1% 510 at ca. 516 nm in aqueous solution

Description | Red to maroon powder or granules

Appearance of the aqueous solution | Red

Identification

Spectrometry | Maximum in water at ca. 516 nm

Purity

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters | Not more than 1 %

Organic compounds other than colouring matters: |

4-aminonaphthalene-1-sulfonic acid | Total not more than 0,5 %

4-hydroxynaphthalene-1-sulfonic acid

Unsulfonated primary aromatic amines | Not more than 0,01 % (calculated as aniline)

Ether extractable matter | Not more than 0,2 % under neutral conditions

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Food Red 9

Definition |

Amaranth consists essentially of trisodium 2-hydroxy-1-(4-sulfonato-1-naphthylazo) naphthalene-3,6-disulfonate and subsidiary colouring matters together with sodium chloride and/or sodium sulphate as the principal uncoloured components. Amaranth is manufactured by coupling 4-amino-1-naphthalenesulphonic acid with 3-hydroxy-2,7-naphthalenedisulphonic acid.

Amaranth is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 16185

Einecs | 213-022-2

Chemical name | Trisodium 2-hydroxy-1-(4-sulfonato-1-naphthylazo) naphthalene-3,6-disulfonate

Chemical formula | C20H11N2Na3O10S3

Molecular weight | 604,48

Assay |

Content not less than 85 % total colouring matters, calculated as the sodium salt

E1cm1% 440 at ca. 520 nm in aqueous solution

Description | Reddish-brown powder or granules

Appearance of the aqueous solution | Red

Identification

Spectrometry | Maximum in water at ca. 520 nm

Purity

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters | Not more than 3,0 %

Organic compounds other than colouring matters: |

4-aminonaphthalene-1-sulfonic acid | Total not more than 0,5 %

3-hydroxynaphthalene-2,7-disulfonic acid

6-hydroxynaphthalene-2-sulfonic acid

7-hydroxynaphthalene-1,3-disulfonic acid

7-hydroxynaphthalene-1,3-6-trisulfonic acid

Unsulfonated primary aromatic amines | Not more than 0,01 % (calculated as aniline)

Ether extractable matter | Not more than 0,2 % under neutral conditions

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Food Red 7; New Coccine

Definition |

Ponceau 4R consists essentially of trisodium 2-hydroxy-1-(4-sulfonato-1-naphthylazo) naphthalene-6,8-disulfonate and subsidiary colouring matters together with sodium chloride and/or sodium sulphate as the principal uncoloured components. Ponceau 4R is manufactured by coupling diazotized naphthionic acid to G acid (2-naphthol-6,8- disulphonic acid) and converting the coupling product to the trisodium salt.

Ponceau 4R is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 16255

Einecs | 220-036-2

Chemical name | Trisodium 2-hydroxy-1-(4-sulfonato-1-naphthylazo) naphthalene-6,8-disulfonate

Chemical formula | C20H11N2Na3O10S3

Molecular weight | 604,48

Assay |

Content not less than 80 % total colouring matters, calculated as the sodium salt.

E1cm1% 430 at ca. 505 nm in aqueous solution

Description | Reddish powder or granules

Appearance of the aqueous solution | Red

Identification

Spectrometry | Maximum in water at ca. 505 nm

Purity

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters | Not more than 1,0 %

Organic compounds other than colouring matters: |

4-aminonaphthalene-1-sulfonic acid | Total not more than 0,5 %

7-hydroxynaphthalene-1,3-disulfonic acid

3-hydroxynaphthalene-2,7-disulfonic acid

6-hydroxynaphthalene-2-sulfonic acid

7-hydroxynaphthalene-1,3-6-trisulfonic acid

Unsulfonated primary aromatic amines | Not more than 0,01 % (calculated as aniline)

Ether extractable matter | Not more than 0,2 % under neutral conditions

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Food Red 14

Definition |

Erythrosine consists essentially of disodium 2-(2,4,5,7-tetraiodo-3-oxido-6-oxoxanthen-9-yl) benzoate monohydrate and subsidiary colouring matters together with water, sodium chloride and/or sodium sulphate as the principal uncoloured components. Erythrosine is manufactured by iodination of fluorescein, the condensation product of resorcinol and phthalic anhydride

Erythrosine is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 45430

Einecs | 240-474-8

Chemical name | Disodium 2-(2,4,5,7-tetraiodo-3-oxido-6-oxoxanthen-9-yl)benzoate monohydrate

Chemical formula | C20H6I4Na2O5 H2O

Molecular weight | 897,88

Assay |

Content not less than 87 % total colouring matters, calculated as the anhydrous sodium salt

E1cm1%1100 at ca. 526 nm in aqueous solution at pH 7

Description | Red powder or granules.

Appearance of the aqueous solution | Red

Identification

Spectrometry | Maximum in water at ca. 526 nm at pH 7

Purity

Inorganic iodides | Not more than 0,1 % (calculated as sodium iodide)

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters (except fluorescein) | Not more than 4,0 %

Fluorescein | Not more than 20 mg/kg

Organic compounds other than colouring matters: |

Tri-iodoresorcinol | Not more than 0,2 %

2-(2,4-dihydroxy-3,5-diiodobenzoyl) benzoic acid | Not more than 0,2 %

Ether extractable matter | From a solution of pH from 7 through 8, not more than 0,2 %

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium Lakes of this colour may be used.

Synonyms | CI Food Red 17

Definition |

Allura Red AC consists essentially of disodium 2-hydroxy-1-(2-methoxy-5-methyl-4-sulfonato-phenylazo) naphthalene-6-sulfonate and subsidiary colouring matters together with sodium chloride and/or sodium sulphate as the principal uncoloured components. Allura Red AC is manufactured by coupling diazotized 5-amino-4-methoxy-2-toluenesulphonic acid with 6-hydroxy-2-naphthalene sulphonic acid

Allura Red AC is described as the sodium salt. The calcium and the potassium salt are also permitted.

Colour Index No | 16035

Einecs | 247-368-0

Chemical name | Disodium 2-hydroxy-1-(2-methoxy-5-methyl-4-sulfonatophenylazo) naphthalene-6-sulfonate

Chemical formula | C18H14N2Na2O8S2

Molecular weight | 496,42

Assay |

Content not less than 85 % total colouring matters, calculated as the sodium salt

E1cm1% 540 at ca. 504 nm in aqueous solution at pH 7

Description | Dark red powder or granules

Appearance of the aqueous solution | Red

Identification

Spectrometry | Maximum in water at ca. 504 nm

Purity

Water insoluble matter | Not more than 0,2 %

Subsidiary colouring matters | Not more than 3,0 %

Organic compounds other than colouring matters: |

6-hydroxy-2-naphthalene sulfonic acid, sodium salt | Not more than 0,3 %

4-amino-5-methoxy-2-methylbenezene sulfonic acid | Not more than 0,2 %

6,6-oxybis (2-naphthalene sulfonic acid) disodium salt | Not more than 1,0 %

Unsulfonated primary aromatic amines | Not more than 0,01 % (calculated as aniline)

Ether extractable matter | From a solution of pH 7, not more than 0,2 %

Arsenic | Not more than 3 mg/kg

Lead | Not more than 2 mg/kg

Mercury | Not more than 1 mg/kg

Cadmium | Not more than 1 mg/kg

Aluminium lakes of this colour may be used.

Synonyms | CI Food Blue 5

Definition |

Patent Blue V consists essentially of the calcium or sodium compound of [4-(α-(4-diethylaminophenyl)-5-hydroxy-2,4-disulfophenyl-methylidene)2,5-cyclohexadien-1-ylidene] diethylammonium hydroxide inner salt and subsidiary colouring matters together with sodium chloride and/or sodium sulphate and/or calcium sulphate as the principal uncoloured components.

The potassium salt is also permitted.

Colour Index No | 42051

This article is long: the rest is at the official publication.