1 ANNEX PARAMETERS REFERRED TO IN ARTICLE 2(1), Decision_act (EU) 2012/688

In forcesince 19 May 2020

Active antenna systems (AAS) means a base station and an antenna system where the amplitude and/or phase between antenna elements is continually adjusted resulting in an antenna pattern that varies in response to short term changes in the radio environment. This excludes long-term beam shaping such as fixed electrical down tilt. In AAS base stations the antenna system is integrated as part of the base station system or product.

Non-active antenna systems (non-AAS) means a base station and an antenna system that provides one or more antenna connectors, which are connected to one or more separately designed passive antenna elements to radiate radio waves. The amplitude and phase of the signals to the antenna elements is not continually adjusted in response to short term changes in the radio environment.

Equivalent isotropically radiated power (EIRP) is the product of the power supplied to the antenna and the antenna gain in a given direction relative to an isotropic antenna (absolute or isotropic gain).

Total radiated power (TRP) is a measure of how much power a composite antenna radiates. It equals the total conducted power input into the antenna array system less any losses in the antenna array system. TRP means the integral of the power transmitted in different directions over the entire radiation sphere as shown in the formula:

where P(θ,φ) is the power radiated by an antenna array system in direction (θ,φ) given by the formula:

P(θ, φ) = PTxg(θ, φ)

where PTx denotes the conducted power (measured in Watts), which is input into the array system, and g(θ,φ) denotes the array system’s directional gain along the (θ, φ) direction.

Within the paired terrestrial 2 GHz band, the frequency arrangement shall be as follows:

(1)

The duplex mode of operation is Frequency Division Duplex (FDD). The duplex spacing shall be 190 MHz with terminal station transmission (FDD uplink) located in the lower part of the band starting at 1920 MHz and finishing at 1980 MHz (‘lower band’) and base station transmission (FDD downlink) located in the upper part of the band starting at 2110 MHz and finishing at 2170 MHz (‘upper band’).

(2)

The assigned block size shall be in multiples of 5 MHz [As the UMTS channel spacing is 200 kHz, the centre frequency of an assigned block used for UMTS can be offset 100 kHz from the centre of the block in the frequency arrangement.]. The lower frequency limit of an assigned block in the lower band of 1 920-1 980 MHz shall be aligned with or spaced at multiples of 5 MHz from its lower edge of 1920 MHz. The lower frequency limit of an assigned block in the upper band of 2 110-2 170 MHz shall be aligned with or spaced at multiples of 5 MHz from its lower edge of 2110 MHz. An assigned block may also have a size in the range of 4,8-5 MHz as long as it fits within the boundaries of a 5 MHz block as defined above.

(3)

The lower band of 1 920-1 980 MHz or portions thereof, can be used for uplink-only operation [Such as Supplemental UpLink (SUL)] without paired spectrum within the upper band of 2 110-2 170 MHz.

(4)

The upper band of 2 110-2 170 MHz or portions thereof, can be used for downlink-only operation [Such as Supplemental DownLink (SDL)] without paired spectrum within the lower band of 1 920-1 980 MHz.

(5)

Base station and terminal station transmission shall be in compliance with the technical conditions specified in Part C and Part D, respectively.

The following technical parameters for base stations called Block Edge Mask (BEM) are an essential component of conditions necessary to ensure coexistence between neighbouring networks, in the absence of bilateral or multilateral agreements between operators of such neighbouring networks. Less stringent technical parameters, if agreed among all affected operators of such networks, may also be used provided that these operators continue to comply with the technical conditions applicable for the protection of other services, applications or networks and with obligations resulting from cross-border coordination.

The BEM consists of several elements given in Table 1. The in-block power limit is applied to a block assigned to an operator. The baseline power limit, designed to protect the spectrum of other operators, and the transitional region power limit, enabling filter roll-off from the in-block to the baseline power limit represent out-of-block elements.

Power limits are provided separately for non-AAS and AAS. For non-AAS, the power limits apply to the mean EIRP. For AAS, the power limits apply to the mean TRP [TRP is a measure of how much power the antenna actually radiates. EIRP and TRP are equivalent for isotropic antennas]. The mean EIRP or mean TRP are measured by averaging over a time interval and over a measurement frequency bandwidth. In the time domain, the mean EIRP or mean TRP is averaged over the active portions of signal bursts and corresponds to a single power control setting. In the frequency domain, the mean EIRP or mean TRP is determined over the measurement frequency bandwidth as given in Tables 2, 3 and 4 below [The actual measurement bandwidth of the measurement equipment used for purposes of compliance testing may be smaller than the measurement bandwidth provided in those tables.]. In general, and unless stated otherwise, the BEM power limits correspond to the aggregate power radiated by the relevant device including all transmit antennas, except in the case of baseline and transition requirements for non-AAS base stations, which are specified per antenna.

BEM element | Definition

In-block | Refers to a block for which the BEM is derived.

Baseline | Spectrum within the FDD downlink frequency band used for WBB ECS, with the exception of block assigned to the operator and the corresponding transitional regions.

Transitional region | Spectrum within the FDD downlink within 0 to 10 MHz below and 0 to 10 MHz above the block assigned to the operator. The transitional regions do not apply below 2110 MHz or above 2170 MHz.

[In a multi-sector base station, the AAS radiated power limit applies to each one of the individual sectors.]

BEM element | Frequency range | Non-AAS EIRP limit | AAS TRP limit

In-block | Block assigned to the operator |

Not obligatory.

In case an upper bound is set by a Member State, a value of 65 dBm/(5 MHz) per antenna may be applied.

Not obligatory.

In case an upper bound is set by a Member State, a value of 57 dBm/(5 MHz) per cell may be applied.

The corresponding in-block TRP limit is determined following guidelines given in ETSI TS 138104 V15.6.0, Annex F, sections F.2 and F.3, on the basis of an antenna gain of 17 dBi and a total of eight beam forming antenna elements (scaling factor of 9 dB):

65 dBm/(5 MHz) – 17 dBi + 9 dB = 57 dBm/(5 MHz).

[The non-AAS BEM level is defined per antenna and applicable to base station configuration with up to four antennas per sector.] [In a multi-sector base station, the AAS radiated power limit applies to each one of the individual sectors.]

BEM element | Frequency range within FDD downlink | Non-AAS mean EIRP limit per antenna | AAS mean TRP limit per cell | Measurement bandwidth

Baseline | Frequencies spaced more than 10 MHz from the lower or upper block edge | 9 dBm | 1 dBm | 5 MHz

[The non-AAS BEM level is defined per antenna and applicable to base station configuration with up to four antennas per sector] [In a multi-sector base station, the AAS radiated power limit applies to each one of the individual sectors.]

BEM element | Frequency range within FDD downlink | Non-AAS mean EIRP limit per antenna | AAS mean TRP limit per cell | Measurement bandwidth

Transitional region | – 10 to – 5 MHz from lower block edge | 11 dBm | 3 dBm | 5 MHz

–

5 to 0 MHz from lower block edge | 16,3 dBm | 8 dBm | 5 MHz

0 to + 5 MHz from upper block edge | 16,3 dBm | 8 dBm | 5 MHz

+ 5 to + 10 MHz from upper block edge | 11 dBm | 3 dBm | 5 MHz

In alignment with the standardisation of unwanted emission conducted power (TRP) for AAS base stations in ETSI TS 138104 (V15.6.0), Annex F, sections F.2 and F.3, the out-of-block TRP limits are set to a value that corresponds to a total of eight beam forming antenna elements, resulting in 8 dB difference between AAS and non-AAS as for the in-block case.

[This power limit is specified as EIRP for terminal stations designed to be fixed or installed and as TRP for terminal stations designed to be mobile or nomadic. EIRP and TRP are equivalent for isotropic antennas. It is recognised that this value may be subject to a tolerance defined in the harmonised standards to take account of operation under extreme environmental conditions and production spread.]

Maximum mean in-block power | 24 dBm

Member States may relax this limit for specific deployments, e.g. fixed terminal stations in rural areas provided that protection of other services, networks and applications is not compromised and cross-border obligations are fulfilled.

Changed on 19 May 2020

The technical conditions presented in this Annex are in the form of frequency arrangements and block-edge masks (BEMs). A BEM is an emission mask that is defined, as a function of frequency, relative to the edge of a block of spectrum for which rights of use are granted to an operator. It consists of in-block and out-of-block components which specify the permitted emission levels over frequencies inside and outside the licensed block of spectrum, respectively. The BEM levels are built up by combining the values listed in the tables below in such a way that the limit at any frequency is given by the highest (least stringent) value of (a) the baseline requirements, (b) the transition requirements, and (c) the in-block requirements (where appropriate). The BEMs are presented as upper limits on the mean equivalentActive antenna systems (AAS) means a base station and an antenna system where the amplitude and/or phase between antenna elements is continually adjusted resulting in an antenna pattern that varies in response to short term changes in the radio environment. This excludes long-term beam shaping such as fixed electrical down tilt. In AAS base stations the antenna system is integrated as part of the base station system or product. Non-active antenna systems (non-AAS) means a base station and an antenna system that provides one or more antenna connectors, which are connected to one or more separately designed passive antenna elements to radiate radio waves. The amplitude and phase of the signals to the antenna elements is not continually adjusted in response to short term changes in the radio environment. Equivalent isotropically radiated power (EIRP) or total radiated power (TRP) [TRP is a measure of how much is the product of the power the antenna actually radiates. The TRP is defined as the integral of the power transmitted in different directions over the entire radiation sphere. EIRP and TRP are equivalent for supplied to the antenna and the antenna gain in a given direction relative to an isotropic antenna (absolute or isotropic antennas.] over an averaging time interval, and over a measurement frequency bandwidth. In the time domain, the EIRP or TRP is averaged over the active portions of signal bursts and corresponds to a single power control setting. In the frequency domain, the EIRP or TRP is determined over the measurement bandwidth specified in point B(2), Tables 1, 2 and 3 [The actual measurement bandwidthgain). Total radiated power (TRP) is a measure of how much power a composite antenna radiates. It equals the total conducted power input into the antenna array system less any losses in the antenna array system. TRP means the integral of the measurement equipment used for purposes of compliance testing may be smaller than the measurement bandwidth provided power transmitted in different directions over the entire radiation sphere as shown in the tables.]. In general, and unless stated otherwise, the BEM levels correspond to the aggregate formula: where P(θ,φ) is the power radiated by the relevant device including all transmit antennas, except in the case of baseline and transition requirements for base stations, which are specified per antenna. BEMs shall be applied as an essential component of the technical conditions necessary to ensure coexistence between services at national level. However, it should be understood that the derived BEMs do not always provide the required level of protection of victim services and additional mitigation techniques would need to be applied in a proportionate manner at national level in order to resolve any remaining cases of interference, also with respect to adjacent bands. Member States shall also ensure that operators of terrestrial systems capable of providing electronic communications services can use less stringent technical parameters than those set out below in points A, B and C provided that the use of these parameters is agreed among all affected parties and that these operators continue to comply with the technical conditions applicable for the protection of other services, applications or networks and with obligations resulting from cross-border coordination. Equipment operating in this band may also make use of power limits other than those set out below provided that appropriate mitigation techniques are applied which comply with Directive 1999/5/EC and which offer at least an equivalent level of protection to that provided by these technical parameters.an antenna array system in direction (θ,φ) given by the formula: P(θ, φ) = PTxg(θ, φ) where PTx denotes the conducted power (measured in Watts), which is input into the array system, and g(θ,φ) denotes the array system’s directional gain along the (θ, φ) direction.

(1) The duplex mode of operation shall be is Frequency Division Duplex (FDD). The duplex spacing shall be 190 MHz with terminal station transmission (FDD uplink) located in the lower part of the band starting at 1920 MHz and finishing at 1980 MHz (‘lower band’) and base station transmission (FDD downlink) located in the upper part of the band starting at 2110 MHz and finishing at 2170 MHz (‘upper band’). (2) The spectrumassigned block edge nearest to 1920 MHz starts at size shall be in multiples of 5 MHz [As the UMTS channel spacing is 200 kHz, the centre frequency of an assigned block used for UMTS can be offset 100 kHz from the centre of the block in the frequency arrangement.]. The lower frequency limit of an assigned block in the lower band of 1 920-1 980 MHz shall be aligned with or spaced at multiples of 5 MHz from its lower edge of 1920,3 MHz or above [Member States may decide to reduce this frequency to 1920,0 MHz for consistency with conditions of existing authorisations.]. The spectrum block edge nearest to 1980 MHz ends at 1979,7 MHz or below [Member States may decide to increase this frequency to 1980,0 MHz for consistency MHz. The lower frequency limit of an assigned block in the upper band of 2 110-2 170 MHz shall be aligned with or spaced at multiples of 5 MHz from its lower edge of 2110 MHz. An assigned block may also have a size in the range of 4,8-5 MHz as long as it fits within the boundaries of a 5 MHz block as defined above. (3) The lower band of 1 920-1 980 MHz or portions thereof, can be used for uplink-only operation [Such as Supplemental UpLink (SUL)] without paired spectrum within the upper band of 2 110-2 170 MHz. (4) The upper band of 2 110-2 170 MHz or portions thereof, can be used for downlink-only operation [Such as Supplemental DownLink (SDL)] without paired spectrum within the lower band of 1 920-1 980 MHz. (5) Base station and terminal station transmission shall be in compliance with the technical conditions of existing authorisations.]. The spectrum block edge nearest to 2110 MHz starts at 2110,3 MHz or above [Member States may decide to reduce this frequency to 2110,0 MHz for consistency specified in Part C and Part D, respectively. The following technical parameters for base stations called Block Edge Mask (BEM) are an essential component of conditions necessary to ensure coexistence between neighbouring networks, in the absence of bilateral or multilateral agreements between operators of such neighbouring networks. Less stringent technical parameters, if agreed among all affected operators of such networks, may also be used provided that these operators continue to comply with the technical conditions of existing authorisations.]. The spectrum applicable for the protection of other services, applications or networks and with obligations resulting from cross-border coordination. The BEM consists of several elements given in Table 1. The in-block edge nearest to 2170 MHz ends at 2169,7 MHz or below [Member States may decide to increase this frequency to 2170,0 MHz for consistency with conditions of existing authorisations.]. Base station and terminal station transmission within the paired terrestrial 2 GHz band shall be in compliance with the BEMs in this Annex. An inpower limit is applied to a block assigned to an operator. The baseline power limit, designed to protect the spectrum of other operators, and the transitional region power limit, enabling filter roll-off from the in-block to the baseline power limit represent out-of-block elements. Power limits are provided separately for non-AAS and AAS. For non-AAS, the power limits apply to the mean EIRP. For AAS, the power limits apply to the mean TRP [TRP is a measure of how much power the antenna actually radiates. EIRP and TRP are equivalent for isotropic antennas]. The mean EIRP or mean TRP are measured by averaging over a time interval and over a measurement frequency bandwidth. In the time domain, the mean EIRP or mean TRP is averaged over the active portions of signal bursts and corresponds to a single power control setting. In the frequency domain, the mean EIRP or mean TRP is determined over the measurement frequency bandwidth as given in Tables 2, 3 and 4 below [The actual measurement bandwidth of the measurement equipment used for purposes of compliance testing may be smaller than the measurement bandwidth provided in those tables.]. In general, and unless stated otherwise, the BEM power limits correspond to the aggregate power radiated by the relevant device including all transmit antennas, except in the case of baseline and transition requirements for non-AAS base stations, which are specified per antenna. BEM element | Definition In-block EIRP limit for base stations is not obligatory. However, Member States may set an | Refers to a block for which the BEM is derived. Baseline | Spectrum within the FDD downlink frequency band used for WBB ECS, with the exception of block assigned to the operator and the corresponding transitional regions. Transitional region | Spectrum within the FDD downlink within 0 to 10 MHz below and 0 to 10 MHz above the block assigned to the operator. The transitional regions do not apply below 2110 MHz or above 2170 MHz. [In a multi-sector base station, the AAS radiated power limit applies to each one of the individual sectors.] BEM element | Frequency range | Non-AAS EIRP limit of between 61 | AAS TRP limit In-block | Block assigned to the operator | Not obligatory. In case an upper bound is set by a Member State, a value of 65 dBm/(5 MHz and 65 ) per antenna may be applied. Not obligatory. In case an upper bound is set by a Member State, a value of 57 dBm/(5 MHz in the FDD downlink band, noting that this) per cell may be applied. The corresponding in-block TRP limit can be increased for specific deployments, e.g. in areas of low population density provided that this does not significantly increase the risk of terminal station receiver blockingis determined following guidelines given in ETSI TS 138104 V15.6.0, Annex F, sections F.2 and F.3, on the basis of an antenna gain of 17 dBi and a total of eight beam forming antenna elements (scaling factor of 9 dB): 65 dBm/(5 MHz) – 17 dBi + 9 dB = 57 dBm/(5 MHz). [The non-AAS BEM level is defined per antenna and applicable to base station configuration with up to four antennas per sector.] Frequency range of out-of-block emissions of [In a multi-sector base station, the AAS radiated power limit applies to each one of the individual sectors.] BEM element | Frequency range within FDD downlink | MaximumNon-AAS mean out-of-block EIRP | limit per antenna | AAS mean TRP limit per cell | Measurement bandwidth Baseline | Frequencies spaced more than 10 MHz from the lower or upper block edge | 9 dBm | 1 dBm | 5 MHz [The non-AAS BEM level is defined per antenna and applicable to base station configuration with up to four antennas per sector.] ] [In a multi-sector base station, the AAS radiated power limit applies to each one of the individual sectors.] BEM element | Frequency range of out-of-block emissions of FDD downlink | Maximumwithin FDD downlink | Non-AAS mean EIRP limit per antenna | AAS mean out-of-block EIRP TRP limit per cell | Measurement bandwidth –Transitional region | – 10 to – 5 MHz from lower block edge | 11 dBm | 3 dBm | 5 MHz – 5 to 0 MHz from lower block edge | 16,3 dBm | 8 dBm | 5 MHz 0 to + 5 MHz from upper block edge | 16,3 dBm | 8 dBm | 5 MHz + 5 to + 10 MHz from upper block edge | 11 dBm | 3 dBm | 5 MHz In alignment with the standardisation of unwanted emission conducted power (TRP) for AAS base stations in ETSI TS 138104 (V15.6.0), Annex F, sections F.2 and F.3, the out-of-block TRP limits are set to a value that corresponds to a total of eight beam forming antenna elements, resulting in 8 dB difference between AAS and non-AAS as for the in-block case. [This power limit is specified as EIRP for terminal stations designed to be fixed or installed and as TRP for terminal stations designed to be mobile or nomadic. EIRP and TRP are equivalent for isotropic antennas. It is recognised that this value may be subject to a tolerance defined in the harmonised standards to take account of operation under extreme environmental conditions and production spread.] [For the determination of out of band emissions of terminals in CEPT Report 39 the maximum conducted transmit power of 23 dBm has been used as a reference.]

Member States may relax thethis limit set out in Table 3 for specific deployments, e.g. fixed terminal stations in rural areas provided that protection of other services, networks and applications is not compromised and cross-border obligations are fulfilled.

  1. 19 May 2020 – todayin force
  2. 5 Nov 2012 – 19 May 2020earlier wording

Versions are held from 5 Nov 2012; the article may be older.