1 ANNEX, Decision_act (EU) 2011/303

In forcesince 20 May 2011
1.

The rules provided for in this Part shall apply when the grading of pig carcasses is carried out by means of the apparatus known as ‘Hennessy Grading Probe (HGP 7)’.

2.

The apparatus shall be equipped with a probe of 5,95 mm diameter (and have abutting 6,3 mm of blade on either side of the probe at its head) containing a photodiode (Siemens LED of the type LYU 260-EO and photodetector of the type 58 MR) and having an operating distance of between 0 and 120 mm. The results of the measurements shall be converted into estimated lean-meat content by means of the HGP 7 itself as well as a computer linked to it.

3.

The lean-meat content of the carcass shall be calculated according to the following formula:

LMP = 65,92 – 0,6337 * Fat + 0,0446 * Muscle

where:

LMPthe estimated percentage of lean meat in the carcass,

Fatthe HGP7 fat depth measurement (including rind) in millimetres, as measured at the third to fourth rib from last rib position, 6 centimetres from the dorsal midline,

Musclethe HGP7 muscle depth measurement (including rind) in millimetres, as measured at the same time and in the same place as Fat.

This formula shall be valid for carcasses weighing between 73,5 and 107,5 kilograms.

1.

The rules provided for in this Part shall apply when the grading of pig carcasses is carried out by means of the apparatus known as ‘Capteur Gras/Maigre — Sydel (CGM)’.

2.

The apparatus shall be equipped with a high-definition Sydel probe 8 mm in diameter, a light-emitting infra-red diode (Honeywell) and two light sensors (Honeywell). The operating distance shall be between 0 and 95 mm.

The results of the measurements shall be converted into estimated lean-meat content by the CGM itself.

3.

The lean-meat content of carcasses shall be calculated using the following formula:

LMP = 66,86 – 0,6549 * Fat + 0,0207 * Muscle

where:

LMPthe estimated percentage of lean meat in the carcass,

Fatthe CGM fat depth measurement (including rind) in millimetres, as measured at the third to fourth rib from last rib position, 6 centimetres from the dorsal midline,

Musclethe CGM muscle depth measurement (including rind) in millimetres, as measured at the same time and in the same place as Fat.

This formula shall be valid for carcasses weighing between 73,5 and 107,5 kilograms.

1.

The rules provided for in this Part shall apply when the grading of pig carcasses is carried out by means of the apparatus known as ‘CSB Image-Meater (CSB)’.

2.

The CSB Image-Meater consists in particular of a video camera, a PC equipped with an image-analysis card, a screen, a printer, a command mechanism, a rate mechanism and interfaces. The Image-Meater variables (16) are all measured at the split line in the ham area (around M. gluteus medius):

The results of the measurements shall be converted into estimates of the percentage of lean meat by using a computer.

3.

The lean-meat content of carcasses shall be calculated according to the following formula:

LMP = 65,2212 – 0,2741 S + 0,0160 F – 0,0302 ML – 0,2648 MS + 0,0831 MF – 0,1002 WL – 0,0509 WaS + 0,0172 WaF – 0,0169 WbS + 0,0006 WbF + 0,0341 WcS – 0,0097 WcF + 0,0223 WdS – 0,0008 WdF + 0,0132 ES – 0,0124 IS,

where the 16 objective CSB measurements, taken at the split line, are:

LMPthe estimated percentage of lean meat in the carcass,

Sfat depth, minimal fat depth over muscle gluteus medius (mm),

Fmuscle depth, minimal muscle depth between anterior extremity of muscle gluteus medius and the dorsal part of the medullar canal (mm),

MLlength of muscle gluteus medius (mm),

MSmean bacon width below muscle gluteus medius (mm),

MFmean lean-meat width below muscle gluteus medius (mm),

WLmean length of vertebrae including spinal discs (mm),

Wa,b,c,dSmean bacon width below 1st measured vertebra (a) and three other vertebrae (b, c, d) (mm),

Wa,b,c,dFmean lean-meat width below 1st measured vertebra (a), and three other vertebrae (b, c, d) (mm),

ESmean external bacon width above the four measured vertebrae (mm),

ISmean internal bacon width above the four measured vertebrae (mm).

4.

The measuring points are described in Part II of the Protocol presented to the Commission by the Netherlands in accordance with Article 23(4) of Regulation (EC) No 1249/2008.

This formula shall be valid for carcasses weighing between 73,5 and 107,5 kilograms.

  • celex=32008R1249