1 ANNEX, Decision_act (EU) 2008/411

In forcesince 8 Feb 2019

Active antenna systems (AAS) means a base station and an antenna system where the amplitude and/or phase between antenna elements is continually adjusted resulting in an antenna pattern that varies in response to short term changes in the radio environment. This excludes long-term beam shaping such as fixed electrical down tilt. In AAS base stations the antenna system is integrated as part of the base station system or product.

Synchronised operation means operation of two or more different time division duplex (TDD) networks, where simultaneous uplink (UL) and downlink (DL) transmissions do not occur, that is at any given moment in time either all networks transmit in downlink or all networks transmit in uplink. This requires the alignment of all DL and UL transmissions for all TDD networks involved as well as synchronising the beginning of the frame across all networks.

Unsynchronised operation means operation of two or more different TDD networks, where at any given moment in time at least one network transmits in DL while at least one network transmits in UL. This might happen if the TDD networks either do not align all DL and UL transmissions or do not synchronise at the beginning of the frame.

Semi-synchronised operation means operation of two or more different TDD networks, where part of the frame is consistent with synchronised operation, while the remaining portion of the frame is consistent with unsynchronised operation. This requires the adoption of a frame structure for all TDD networks involved, including slots where the UL/DL direction is not specified, as well as synchronising the beginning of the frame across all networks.

Total radiated power (TRP) is a measure of how much power a composite antenna radiates. It equals the total conducted power input into the antenna array system less any losses in the antenna array system. TRP means the integral of the power transmitted in different directions over the entire radiation sphere as shown in the formula:

where P(, φ) is the power radiated by an antenna array system in direction (, φ) given by the formula:

P(, φ) = PTxg(, φ)

where PTx denotes the conducted power (measured in Watts), which is input to the array system, and g(, φ) denotes the array systems directional gain along the (, φ) direction.

Within the 3400-3800 MHz frequency band:

1.

the duplex mode of operation shall be time division duplex (TDD);

2.

the assigned block sizes shall be in multiples of 5 MHz. The lower frequency limit of an assigned block shall be aligned with or spaced at multiples of 5 MHz from the lower band edge of 3400 MHz [If assigned blocks need to be offset to accommodate other existent users, a raster of 100 kHz must be used. Narrower blocks can be defined adjacent to other users, to allow efficient use of spectrum.];

3.

there shall be spectrum available providing the opportunity to access sufficiently large portions of contiguous spectrum, preferably 80-100 MHz, for wireless broadband electronic communications services;

4.

base stations and terminal stations transmission shall be in compliance with the technical conditions specified in Part C and Part D, respectively.

The following technical parameters for base stations called block edge mask (BEM) are an essential component of conditions necessary to ensure coexistence between neighbouring networks, in the absence of bilateral or multilateral agreements between operators of such neighbouring networks. Less stringent technical parameters, if agreed among the operators of such networks, may also be used.

The BEM consists of several elements given in Table 1. The in-block power limit is applied to a block owned by an operator. The baseline power limit, designed to protect the spectrum of other operators, the transitional region power limit, enabling filter roll-off from the in-block to the baseline power limit, and the restricted baseline power limit applicable to cases of unsynchronised or semi-synchronised operation represent out-of-block elements. The additional baseline power limit is an out-of-band power limit which is used either for the protection of radar operation below 3400 MHz or for the protection of fixed satellite services (FSS) and fixed services (FS) above 3800 MHz.

Tables 2 to 7 contain the power limits for the different BEM elements for TDD networks providing wireless broadband (WBB) electronic communications services (ECS). Power limits are provided for synchronised, unsynchronised and semi-synchronised WBB ECS networks.

In Tables 3 and 4, the power level PMax is the maximum carrier power in dBm for the base station in question. PMax is defined and measured as the equivalent isotropically radiated power (e.i.r.p.) per antenna for base stations with non-active antenna systems (non-AAS). For AAS, base stations PMax is defined as the maximum mean carrier power in dBm for the base station and measured as TRP per carrier in a given cell.

In Tables 3, 4, and 7 the power limits are determined relative to a fixed upper limit by means of the formula Min(PMax – A, B), which sets the lower (or stricter) of two values: (1) (PMax – A) expressing the maximum carrier power PMax minus a relative offset A, and (2) the fixed upper limit B.

To obtain a BEM for a specific block, the BEM elements that are defined in Table 1 are combined in the following steps:

1.

in-block power limit is used for the block assigned to the operator;

2.

transitional regions are determined, and corresponding power limits are used;

3.

baseline power limit is used in the case of synchronised WBB ECS networks for spectrum within the band except from the operator's block in question and the corresponding transitional regions;

4.

restricted baseline power limits are used in the case of unsynchronised and semi-synchronised WBB ECS networks;

5.

for spectrum below 3400 MHz the respective additional baseline power limit is used;

6.

for coexistence with FSS/FS above 3800 MHz an additional baseline power limit is used.

The Figure below provides an example of the combination of different BEM elements.

BEM element | Definition

In-block | Refers to a block for which the BEM is derived.

Baseline | Spectrum within 3400-3800 MHz used for WBB ECS, with the exception of the block assigned to the operator and the corresponding transitional regions.

Transitional region | Spectrum within 0 to 10 MHz below and 0 to 10 MHz above the block assigned to the operator. Transitional regions do not apply to TDD blocks assigned to other operators, unless networks are synchronised. The transitional regions do not apply below 3400 MHz or above 3800 MHz.

Additional baseline | Spectrum below 3400 MHz and above 3800 MHz.

Restricted baseline | Spectrum used for WBB ECS by networks unsynchronised or semi-synchronised with the operator's block in question.

The BEM elements are applicable to base stations with different power levels, typically referred to as macro, micro, pico, and femto base stations [These terms are not uniquely defined and refer to cellular base stations with different power levels, which decrease in the following order: macro, micro, pico, femto. In particular, femto cells are small base stations with the lowest power levels, which are typically used indoors.].

BEM element | Frequency range | Power limit for non-AAS and AAS base stations

In-block | Block assigned to the operator | Not obligatory.

In the specific case of femto base stations, power control shall be applied to minimize interference to adjacent channels. The requirement on power control for femto base stations results from the need to reduce interference from equipment that may be deployed by consumers and may thus not be coordinated with surrounding networks. Member States wishing to include a limit in their authorisation or to use a limit for coordination purposes may define such limits on a national basis.

[PMax is the maximum mean carrier power in dBm for the base station measured as e.i.r.p. per carrier per antenna] [PMax′ is the maximum mean carrier power in dBm for the base station measured as TRP per carrier in a given cell] [In a multi-sector base station, the radiated power limit applies to each one of the individual sectors.]

BEM element | Frequency range | Non-AAS e.i.r.p limit | AAS TRP limit

Baseline |

Below – 10 MHz offset from lower block edge

Above 10 MHz offset from upper block edge

Within 3400-3800 MHz

Min(PMax – 43, 13) dBm/(5 MHz) per antenna | Min(PMax′ – 43, 1) dBm/(5 MHz) per cell

The applied fixed upper limit (13 dBm/(5 MHz) for non-AAS or 1 dBm/(5 MHz) for AAS) provides an upper bound on the interference from a base station. When two TDD blocks are synchronised, there will be no interference between base stations.

[PMax is the maximum mean carrier power in dBm for the base station measured as e.i.r.p. per carrier per antenna] [PMax′ is the maximum mean carrier power in dBm for the base station measured as TRP per carrier in a given cell] [In a multi-sector base station, the radiated power limit applies to each one of the individual sectors.]

BEM element | Frequency range | Non-AAS e.i.r.p limit | AAS TRP limit

Transitional region |

–

5 to 0 MHz offset from lower block edge or

0 to 5 MHz offset from upper block edge

Min(PMax – 40, 21) dBm/(5 MHz) per antenna | Min(PMax′ – 40, 16) dBm/(5 MHz) per cell

Transitional region |

–

10 to – 5 MHz offset from lower block edge or

5 to 10 MHz offset from upper block edge

Min(PMax – 43, 15) dBm/(5 MHz) per antenna | Min(PMax′ – 43, 12) dBm/(5 MHz) per cell

[In a multi-sector base station, the radiated power limit applies to each one of the individual sectors.]

BEM element | Frequency range | Non AAS e.i.r.p limit | AAS TRP limit

Restricted baseline | Unsynchronised and semi synchronised blocks, below the lower block edge and above the upper block edge, within 3400-3800 MHz | – 34 dBm/(5 MHz) per cell | – 43 dBm/(5 MHz) per cell

These restricted power limits are used for unsynchronised and semi-synchronised operations of base stations, if no geographic separation is available. In addition, depending on national circumstances, Member States may define a relaxed alternative restricted baseline power limit applying to specific implementation cases to ensure a more efficient usage of spectrum.

[Alternative measures may be required on a case by case basis for indoor AAS base stations on a national basis.] [In cases where Member States have already implemented a guard band when issuing licences for terrestrial systems capable of providing WBB ECS before the adoption of this Decision and in accordance with Commission Decision 2008/411/EC, those Member States may apply the additional baseline only below such guard band, provided it complies with the protection of radars in the adjacent band and with cross-border obligations.] [In a multi-sector base station, the radiated power limit applies to each one of the individual sectors]

Case | BEM element | Frequency range | Non-AAS e.i.r.p limit | AAS TRP limit

A | Member States with military radiolocation systems below 3400 MHz | Additional baseline | Below 3400 MHz | – 59 dBm/MHz per antenna | – 52 dBm/MHz per cell

B | Member States with military radiolocation systems below 3400 MHz | Additional baseline | Below 3400 MHz | – 50 dBm/MHz per antenna

C | Member States without adjacent band usage or with usage that does not need extra protection | Additional baseline | Below 3400 MHz | Not applicable | Not applicable

The additional baseline power limits reflect the need for protection of military radiolocation in some countries. Member States may select the limits from case A or B for non AAS depending on the level of protection required for the radar in the region in question. A coordination zone of up to 12 km around fixed terrestrial radars, based on AAS TRP limit of – 52 dBm/MHz per cell, may be required. Such coordination is under responsibility of the relevant Member State.

Other mitigation measures like geographical separation, coordination on a case-by-case basis or an additional guard band may be necessary. In case of indoor deployments, Member States may define a relaxed limit applying to specific implementation cases.

[PMax is the maximum mean carrier power in dBm for the base station measured as e.i.r.p. per carrier per antenna] [PMax′ is the maximum mean carrier power in dBm for the base station measured as TRP per carrier in a given cell] [In a multi-sector base station, the radiated power limit refers to the level corresponding to each one of the individual sectors]

BEM element | Frequency range | Non-AAS e.i.r.p limit | AAS TRP power limit

Additional baseline | 3800-3805 MHz | Min(PMax – 40, 21) dBm/(5 MHz) per antenna | Min(PMax′ – 40, 16) dBm/(5 MHz) per cell

3805-3810 MHz | Min(PMax – 43, 15) dBm/(5 MHz) per antenna | Min(PMax′ – 43, 12) dBm/(5 MHz) per cell

3810-3840 MHz | Min(PMax – 43, 13) dBm/(5 MHz) per antenna | Min(PMax′ – 43, 1) dBm/(5 MHz) per cell

Above 3840 MHz | – 2 dBm/(5 MHz) per antenna | – 14 dBm/(5 MHz) per cell

The additional baseline power limits are applied at the 3800 MHz band edge to support the coordination process to be carried out at national level.

Maximum in-block power | 28 dBm TRP

The inblock radiated power limit for fixed/nomadic terminal stations may exceed the limit in Table 8 provided cross-border obligations are fulfilled. For such terminal stations mitigation measures to protect radar below 3400 MHz may be necessary, for example, geographical separation or an additional guard band.

Changed on 8 Feb 2019

1. The preferred duplex mode of operation in the 3400-3600 MHz sub-band shall be Time Division Duplex (TDD). 2. Member States may alternatively implement Frequency Division Duplex (FDD) mode of operation in the 3400-3600 MHz sub-band for the purpose of: (a) ensuring greater efficiency of spectrum use, such as when sharing with existing rights of use during a co-existence period or implementing market-based spectrum management; or (b) protecting existing uses or avoiding interference; or (c) coordination Active antenna systems (AAS) means a base station and an antenna system where the amplitude and/or phase between antenna elements is continually adjusted resulting in an antenna pattern that varies in response to short term changes in the radio environment. This excludes long-term beam shaping such as fixed electrical down tilt. In AAS base stations the antenna system is integrated as part of the base station system or product. Synchronised operation means operation of two or more different time division duplex (TDD) networks, where simultaneous uplink (UL) and downlink (DL) transmissions do not occur, that is at any given moment in time either all networks transmit in downlink or all networks transmit in uplink. This requires the alignment of all DL and UL transmissions for all TDD networks involved as well as synchronising the beginning of the frame across all networks. Unsynchronised operation means operation of two or more different TDD networks, where at any given moment in time at least one network transmits in DL while at least one network transmits in UL. This might happen if the TDD networks either do not align all DL and UL transmissions or do not synchronise at the beginning of the frame. Semi-synchronised operation means operation of two or more different TDD networks, where part of the frame is consistent with non-EU countries. Where the FDD mode of operation is implemented, the duplex spacing shall be 100 MHz with terminal station transmission (FDD uplink) located synchronised operation, while the remaining portion of the frame is consistent with unsynchronised operation. This requires the adoption of a frame structure for all TDD networks involved, including slots where the UL/DL direction is not specified, as well as synchronising the beginning of the frame across all networks. Total radiated power (TRP) is a measure of how much power a composite antenna radiates. It equals the total conducted power input into the antenna array system less any losses in the lower part antenna array system. TRP means the integral of the band starting at 3410 MHz and finishing at 3490 MHz and base station transmission (FDD downlink) located in the upper part of the band starting at 3510 MHz and finishing at 3590 MHz. 3. The duplex mode of operation in the 3600power transmitted in different directions over the entire radiation sphere as shown in the formula: where P(, φ) is the power radiated by an antenna array system in direction (, φ) given by the formula: P(, φ) = PTxg(, φ) where PTx denotes the conducted power (measured in Watts), which is input to the array system, and g(, φ) denotes the array systems directional gain along the (, φ) direction. Within the 3400-3800 MHz sub-frequency band : 1. the duplex mode of operation shall be Time Division Duplex. 4. Thetime division duplex (TDD); 2. the assigned block sizes shall be in multiples of 5 MHz. The lower frequency limit of an assigned block shall be aligned with or spaced at multiples of 5 MHz from the relevant sub-lower band edge of 3400 MHz [If assigned blocks need to be offset to accommodate other existingexistent users, a raster of 100 kHz must be used. Narrower blocks can be defined adjacent to other users, to allow efficient use of spectrum.]. Depending on the duplex mode of operation the relevant sub-band edges are: 3400 MHz and 3600 MHz for TDD; 3410 MHz and 3510 MHz for FDD. 5. Base station; 3. there shall be spectrum available providing the opportunity to access sufficiently large portions of contiguous spectrum, preferably 80-100 MHz, for wireless broadband electronic communications services; 4. base stations and terminal stationstations transmission within the 3400-3800 MHz band shall be in compliance with the Block Edge Mask in this Annextechnical conditions specified in Part C and Part D, respectively. The following technical parameters for base stations called block edge mask (BEM) are an essential component of conditions necessary to ensure coexistence between neighbouring networks, in the absence of bilateral or multilateral agreements between operators of such neighbouring networks. Less stringent technical parameters, if agreed among the operators of such networks, may also be used. The BEM consists of several elements given in Table 1, both for the 3400-3600 MHz and the 3600-3800 MHz sub-band. The in-block power limit is applied to a block owned by an operator. The baseline power limit, designed to protect the spectrum of other operators, and the transitional region power limitslimit, enabling filter roll-off from the in-block to the baseline power limit , and the restricted baseline power limit applicable to cases of unsynchronised or semi-synchronised operation represent out-of-block elements. The guard bands apply only in the case of using FDD in the additional baseline power limit is an out-of-band power limit which is used either for the protection of radar operation below 3400-3600 MHz sub-band. The BEM is applicable to base stations with different power levels (typically referred to as macro, micro, pico and femto base stations [These terms are not uniquely defined and refer to cellular base stations with different power levels, which decrease in the following order: macro, micro, pico, femto, In particular, femto cells are small base stations with the lowest MHz or for the protection of fixed satellite services (FSS) and fixed services (FS) above 3800 MHz. Tables 2 to 7 contain the power limits for the different BEM elements for TDD networks providing wireless broadband (WBB) electronic communications services (ECS). Power limits are provided for synchronised, unsynchronised and semi-synchronised WBB ECS networks. In Tables 3 and 4, the power level PMax is the maximum carrier power levels, which are typically used indoors.]). Tables 2 to 6 contain the power limits for the different BEM elements. The in-block in dBm for the base station in question. PMax is defined and measured as the equivalent isotropically radiated power limit is applied to a block owned by an operator. Power limits are provided also for guard bands and for the protection of radar operation below 3400 MHz. The frequency ranges in Tables 1 to 6 depend on the duplex mode chosen for the 3400-3600 MHz sub-band (TDD or alternatively FDD). PMax is the maximum carrier power for the base station in question, measured as EIRP [Equivalent Isotropic Radiated Power.]. Synchronized operation means operation of TDD in two different networks where no simultaneous uplink and downlink transmissions occur, as defined in applicable standards(e.i.r.p.) per antenna for base stations with non-active antenna systems (non-AAS). For AAS, base stations PMax is defined as the maximum mean carrier power in dBm for the base station and measured as TRP per carrier in a given cell. In Tables 3, 4, and 7 the power limits are determined relative to a fixed upper limit by means of the formula Min(PMax – A, B), which sets the lower (or stricter) of two values: (1) (PMax – A) expressing the maximum carrier power PMax minus a relative offset A, and (2) the fixed upper limit B.

1. Inin-block power limit is used for the block assigned to the operator. 2. Transitional; 2. transitional regions are determined, and corresponding power limits are used. The transitional regions may overlap with guard bands, in which case transitional region power limits are used. 3. For the remaining spectrum assigned to FDD or TDD, ; 3. baseline power limit is used in the case of synchronised WBB ECS networks for spectrum within the band except from the operator's block in question and the corresponding transitional regions; 4. restricted baseline power limits are used. 4. For the remaining guard band spectrum, guard band power limits are used. 5. For in the case of unsynchronised and semi-synchronised WBB ECS networks; 5. for spectrum below 3400 MHz, one of the the respective additional baseline power limitslimit is used. The Figure provides an example of the combination of different BEM elements. In the case of unsynchronized TDD networks, the compliance of two adjacent operators ; 6. for coexistence with the BEM requirements could be achieved by introducing frequency separation (e.g. through the authorisation process at national level) between the block edges of both operators. As another option, the so-called restricted blocks may be introduced for two adjacent operators which would require them to FSS/FS above 3800 MHz an additional baseline power limit the power level is used in the upper- or lowermost portions of their assigned spectrum blocks [A recommended value for such limited power level is 4 dBm/5 MHz EIRP per cell applied to the upper- or lowermost 5 MHz of an operator's assigned spectrum block.].. The Figure below provides an example of the combination of different BEM elements.

Baseline | Spectrum used for TDD, FDD uplink or FDD downlinkwithin 3400-3800 MHz used for WBB ECS, with the exception of the block assigned to the operator and the corresponding transitional regions. Transitional region | For FDD downlink blocks, the transitional region applies Spectrum within 0 to 10 MHz below and 0 to 10 MHz above the block assigned to the operator. For Transitional regions do not apply to TDD blocks, the transitional region applies 0 to 10 MHz below and 0 to 10 MHz above the block assigned to the operator. The transitional region applies to adjacent TDD blocks assigned to other operators if networks are synchronised, or to spectrum in-between adjacent TDD blocks that are separated by 5 or 10 MHz. Transitional regions do not apply to adjacent TDD blocks assigned to other operators, if networks are not synchronised. The transitional region does not apply below 3400 MHz or above 3800 MHz. Guard bands | The following guard bands apply in case of an FDD allocation: 3400-3410, 3490-3510 (duplex gap) and 3590-3600 MHz In case of overlap between transitional regions and guard bands, transitional assigned to other operators, unless networks are synchronised. The transitional regions do not apply below 3400 MHz or above 3800 MHz. Additional baseline | Spectrum below 3400 MHz and above 3800 MHz. Restricted baseline | Spectrum used for WBB ECS by networks unsynchronised or semi-synchronised with the operator's block in question. The BEM elements are applicable to base stations with different power levels, typically referred to as macro, micro, pico, and femto base stations [These terms are not uniquely defined and refer to cellular base stations with different power levels, which decrease in the following order: macro, micro, pico, femto. In particular, femto cells are small base stations with the lowest power limits are levels, which are typically used. Additional baseline | Spectrum below 3400 MHz. indoors.]. BEM element | Frequency range | Power limit for non-AAS and AAS base stations In-block | Block assigned to the operator | Not obligatory. In case an upper bound is desired by an administration, a value must be applied which does not exceed 68 dBm/5 MHz per antenna. For the specific case of femto base stations, power control shouldshall be applied to minimize interference to adjacent channels. The requirement on power control for femto base stations results from the need to reduce interference from equipment that may be deployed by consumers and may thus not be coordinated with surrounding networks. [An exception for this baseline can be negotiated between adjacent operators for femto base stations in the case when there is no risk for interference to macro Member States wishing to include a limit in their authorisation or to use a limit for coordination purposes may define such limits on a national basis. [PMax is the maximum mean carrier power in dBm for the base stations. In that case – 25 dBm/5MHz EIRP per station measured as e.i.r.p. per carrier per antenna] [PMax′ is the maximum mean carrier power in dBm for the base station measured as TRP per carrier in a given cell may be used] [In a multi-sector base station, the radiated power limit applies to each one of the individual sectors.] BEM element | Frequency range | Power Non-AAS e.i.r.p limit | AAS TRP limit

FDD downlink (3510-3590 MHz). Synchronized TDD blocks (3400-3800 MHz or 3600Below – 10 MHz offset from lower block edge Above 10 MHz offset from upper block edge Within 3400-3800 MHz). Min(PMax — 43,– 43, 13) dBm/(5 MHz EIRP ) per antenna Baseline | FDD uplink (3410-3490 MHz). Unsynchronised TDD blocks (3400-3800 MHz or 3600-3800 MHz). – 34 | Min(PMax′ – 43, 1) dBm/(5 MHz EIRP ) per cell The baseline for FDD downlink and synchronised TDD is expressed by combining attenuation relative to the maximum carrier power with a applied fixed upper limit. The stricter of the two requirements applies. The fixed level (13 dBm/(5 MHz) for non-AAS or 1 dBm/(5 MHz) for AAS) provides an upper bound on the interference from a base station. When two TDD blocks are synchronizedsynchronised, there will be no interference between base stations. In this case, the same baseline as [PMax is the maximum mean carrier power in dBm for the FDD downlink region is used. The baseline base station measured as e.i.r.p. per carrier per antenna] [PMax′ is the maximum mean carrier power limit for FDD uplink and unsynchronised TDD is expressed as a fixed in dBm for the base station measured as TRP per carrier in a given cell] [In a multi-sector base station, the radiated power limit only.applies to each one of the individual sectors.] BEM element | Frequency range | Power Non-AAS e.i.r.p limit | AAS TRP limit

Min(PMax — 40,– 40, 21) dBm/(5 MHz EIRP ) per antenna | Min(PMax′ – 40, 16) dBm/(5 MHz) per cell

Min(PMax — 43,– 43, 15) dBm/(5 MHz EIRP ) per antenna The transitional region power limits are defined to enable the reduction of power from the in-block level to the baseline or guard band levels. The requirements are expressed as attenuation relative to the maximum carrier power, combined with a fixed upper limit. The stricter of the two requirements applies. BEM element | Frequency range | Power limit Guard band | | Min(PMax′ – 43, 12) dBm/(5 MHz) per cell [In a multi-sector base station, the radiated power limit applies to each one of the individual sectors.] BEM element | Frequency range | Non AAS e.i.r.p limit | AAS TRP limit Restricted baseline | Unsynchronised and semi synchronised blocks, below the lower block edge and above the upper block edge, within 3400-34103800 MHz | – 34 dBm/(5 MHz EIRP ) per cell Guard band | 3490-3500 MHz | – 23 | – 43 dBm/(5 MHz per antenna port Guard band | 3500-3510 MHz | Min(PMax — 43,13) dBm/5 MHz EIRP per antenna Guard band | 3590-3600 MHz | Min(PMax — 43,13) dBm/5 MHz EIRP per antenna For the guard band 3400-3410 MHz, the ) per cell These restricted power limits are used for unsynchronised and semi-synchronised operations of base stations, if no geographic separation is available. In addition, depending on national circumstances, Member States may define a relaxed alternative restricted baseline power limit is chosen to be the same as the baseline in the adjacent FDD uplink (3410-3490 MHz). For the guard bands 3500-3510 MHz and 3590-3600 MHz, the power limit is chosen to be the same as the baseline in the adjacent FDD downlink (3510-3590 MHz). For the applying to specific implementation cases to ensure a more efficient usage of spectrum. [Alternative measures may be required on a case by case basis for indoor AAS base stations on a national basis.] [In cases where Member States have already implemented a guard band 3490-3500 MHz, the power limit is based on the spurious emission requirement of – 30 dBm/MHz at the antenna port converted to 5 MHz bandwidth. [Administrations may choose to have a guard band when issuing licences for terrestrial systems capable of providing WBB ECS before the adoption of this Decision and in accordance with Commission Decision 2008/411/EC, those Member States may apply the additional baseline only below 3400 MHz. In that case the power limit may apply below the guardsuch guard band, provided it complies with the protection of radars in the adjacent band onlyand with cross-border obligations.] [Administrations may select the limit from case A or B depending on the level of protection required for the radar in the region in question.In a multi-sector base station, the radiated power limit applies to each one of the individual sectors] Case | BEM element | Frequency range | Power Non-AAS e.i.r.p limit A | Union countries | AAS TRP limit A | Member States with military radiolocation systems below 3400 MHz | Additional Baselinebaseline | Below 3400 MHz for both TDD and FDD designation | – 59| – 59 dBm/MHz per antenna | – 52 dBm/MHz EIRP B | Union countriesper cell B | Member States with military radiolocation systems below 3400 MHz | Additional Baselinebaseline | Below 3400 MHz for both TDD and FDD designation | – 50 dBm/MHz EIRP C | Union countriesper antenna C | Member States without adjacent band usage or with usage that does not need extra protection | Additional Baselinebaseline | Below 3400 MHz for both TDD and FDD designation | Not applicable | Not applicable The additional baseline power limits reflect the need for protection forof military radiolocation in some countries. Cases A, B and C can be applied per region or country so that the adjacent band may have different levels of protection in different geographical areas or countries, depending on the deployment of the adjacent band systems. Member States may select the limits from case A or B for non AAS depending on the level of protection required for the radar in the region in question. A coordination zone of up to 12 km around fixed terrestrial radars, based on AAS TRP limit of – 52 dBm/MHz per cell, may be required. Such coordination is under responsibility of the relevant Member State. Other mitigation measures like geographical separation, coordination on a case-by-case basis or an additional guard band may be necessary for a TDD mode of operation. The additional baseline power limits given in Table 6 are applicable only to outdoor cells. In the case of an indoor cell, the . In case of indoor deployments, Member States may define a relaxed limit applying to specific implementation cases. [PMax is the maximum mean carrier power limits can be relaxed on a case by case basis. For terminal stations, other mitigation measures may be necessary such as geographical separation or an additional guard band for both the FDD and TDD mode of operation. [Note in particular that different baseline levels are defined for different parts of the spectrum and that the power limit in dBm for the base station measured as e.i.r.p. per carrier per antenna] [PMax′ is the maximum mean carrier power in dBm for the base station measured as TRP per carrier in a given cell] [In a multi-sector base station, the radiated power limit refers to the level corresponding to each one of the lower transitional region is used in a part of the guard band 3490–3510 MHz. Spectrum below 3400 MHz has not been included in the Figure, although the BEM element ‘additional baseline’ may be applied to protect military radiolocation.] [This power limit is specified as EIRP for terminal stations designed to be fixed or installed and as total radiated power (TRP) for terminal stations designed to be mobile or nomadic. EIRP and TRP are equivalent for isotropic antennas. It is recognised that this value may be subject to a tolerance (of up to 2 dB) defined in the harmonised standards to take account of operation under extreme environmental conditions and production spread.]individual sectors] BEM element | Frequency range | Non-AAS e.i.r.p limit | AAS TRP power limit Additional baseline | 3800-3805 MHz | Min(PMax – 40, 21) dBm/(5 MHz) per antenna | Min(PMax′ – 40, 16) dBm/(5 MHz) per cell 3805-3810 MHz | Min(PMax – 43, 15) dBm/(5 MHz) per antenna | Min(PMax′ – 43, 12) dBm/(5 MHz) per cell 3810-3840 MHz | Min(PMax – 43, 13) dBm/(5 MHz) per antenna | Min(PMax′ – 43, 1) dBm/(5 MHz) per cell Above 3840 MHz | – 2 dBm/(5 MHz) per antenna | – 14 dBm/(5 MHz) per cell The additional baseline power limits are applied at the 3800 MHz band edge to support the coordination process to be carried out at national level. Maximum in-block power | 25 dBm Member States may relax the 28 dBm TRP The inblock radiated power limit set out in Table 7 under certain circumstances, for example fixed terminal stations, provided that protection and continued operation of other existing use in the for fixed/nomadic terminal stations may exceed the limit in Table 8 provided cross-border obligations are fulfilled. For such terminal stations mitigation measures to protect radar below 3400-3800 MHz band is not compromised and cross-border obligations are fulfilled MHz may be necessary, for example, geographical separation or an additional guard band.

  1. 8 Feb 2019 – todayin force
  2. 14 May 2014 – 8 Feb 2019earlier wording
  3. 21 May 2008 – 14 May 2014earlier wording