The tables set out in this Annex, list construction products and/or materials which satisfy all of the requirements for the performance characteristic reaction to fire without need for testing.
[Mounted in accordance with EN ISO 9239-1, on a substrate of at least Class D - s2, d0 and with minimum density of 400 kg/m3 or with an air gap underneath.] [An interlayer of at least Class E and with maximum thickness 3 mm may be included in applications without an air gap, for parquet products with 14 mm thickness or more and for veneered floor coverings.] [Class as provided for in Commission Decision 2000/147/EC Annex Table 2.] [Type and quantity of surface coatings included are acrylic, polyurethane or soap, 50 - 100 g/m2, and oil, 20 - 60 g/m2.] [Conditioned according to EN 13238 (50 % RH 23 oC).] [Substrate at least Class A2 - s1, d0.] [Applies also to steps of stairs.]
Material, | Product detail |
Minimum mean density
(kg/m3)
Minimum overall thickness
(mm)
End-use condition | Class for floorings
Wood flooring and parquet | Solid flooring of oak or beech with surface coating |
Beech: 680
Oak: 650
8 | Glued to substrate | Cfl - s1
Solid flooring of oak, beech or spruce and with surface coating |
Beech: 680
Oak: 650
Spruce: 450
20 | With or without air gap underneath
Solid wood flooring with surface coating and not specified above | 390 | 8 | Without air gap underneath | Dfl - s1
20 | With or without air gap underneath
Wood parquet | Multilayer parquet with a top layer of oak of at least 5 mm thickness and with surface coating |
650
(top layer)
10 | Glued to substrate | Cfl - s1
14 | With or without air gap underneath
Multilayer parquet with surface coating and not specified above | 500 | 8 | Glued to substrate | Dfl - s1
10 | Without air gap underneath
14 | With or without air gap underneath
Veneered floor covering | Veneered floor covering with surface coating | 800 | 6 | Without air gap underneath | Dfl - s1
[Mounted mechanically on a wood batten support frame, with the gap closed or filled with a substrate of at least class A2 – s1, d0 with minimum density of 10 kg/m3 or filled with a substrate of cellulose insulation material of at least class E and with or without a vapour barrier behind. The wood product shall be designed to be mounted without open joints.] [Mounted mechanically on a wood batten support frame, with or without an open air gap behind. The wood product shall be designed to be mounted without open joints.] [Class as provided for in Table 1 of Annex to Delegated Regulation (EU) 2016/364.] [An open air gap may include possibility for ventilation behind the product, while a closed air gap will exclude such ventilation. The substrate behind the air gap must be of at least class A2 – s1, d0 with a minimum density of 10 kg/m3. Behind a closed air gap of maximum 20 mm and with vertical wood pieces, the substrate may be of at least class D – s2, d0.] [Joints include all types of joints e.g., butt joints and tongue and groove joints; Untreated wood is a wooden material that was not coated and was not subject to any kind of treatment other than kiln drying (physical, chemical, impregnation, or other treatments).] [Conditioned according to EN 13238.] [As illustrated in Figure a. Profiled area of the exposed side of the panel not more than 20 % of the plane area, or 25 % if measured at both exposed and unexposed side of the panel. For butt joints, the larger thickness applies at the joint interface.] [Rectangular wood pieces, with or without rounded corners, mounted horizontally or vertically on a support frame and surrounded by air on all sides, mainly used close to other building elements, both in interior and exterior applications.] [Maximum exposed area (all sides of rectangular wood pieces and wood support frame) not more than 110 % of the total plane area, see Figure b.] [Other building elements closer than 100 mm from the wood ribbon element (excluding its support frame) must be of at least class A2 – s1, d0, at distances 100–300 mm of at least class B – s1, d0 and at distances more than 300 mm of at least class D – s2, d0.] [Applies also to staircase risers.]
Product | Product detail | Minimum mean density (kg/m3) | Minimum thicknesses, total/minimum (mm) | End-use condition | Class
Panelling and cladding | Untreated wood pieces with or without tongue and groove and with or without profiled surface | 390 | 9/6 | Without air gap or with closed air gap behind | D – s2, d2
12/8 | D – s2, d0
Panelling and cladding | Untreated wood pieces with or without tongue and groove and with or without profiled surface | 390 | 9/6 | With open air gap ≤ 20 mm behind | D – s2, d0
18/12 | Without air gap or with open air gap behind
Wood ribbon elements | Untreated wood pieces mounted on a support frame | 390 | 18 | Surrounded by open air on all sides | D – s2, d0
nnumber of wood pieces per metre
tthickness of each wood piece, in metre
wwidth of each wood piece, in metre
aexposed area of wood support frame (if any), in m2, per m2 of wood ribbon element