Introduction
This Annex lays down the uniform waste classification and acceptance procedure according to Annex II to Directive 1999/31/EC on the landfill of waste (the "Landfill Directive").
In accordance with Article 176 of the Treaty, Member States are not prevented from maintaining or introducing more stringent protective measures than those established in this Annex, provided that such measures are compatible with the Treaty. Such measures shall be notified to the Commission. This could be of particular relevance with reference to the limit values for cadmium and mercury in section 2. Member States may also introduce limit values for components not included in section 2.
Section 1 of this Annex lays down the procedure to determine the acceptability of waste at landfills. This procedure consists of the basic characterisation, compliance testing and on-site verification as defined in section 3 of Annex II to the Landfill Directive.
Section 2 of this Annex lays down the acceptance criteria for each landfill class. Waste may be accepted at a landfill only if it fulfils the acceptance criteria of the relevant landfill class as laid down in section 2 of this Annex.
Section 3 of this Annex lists the methods to be used for the sampling and testing of waste.
Appendix A defines the safety assessment to be carried out for underground storage.
Appendix B is an informative Annex providing an overview of the landfill options available within the Directive and examples of possible subcategorisation of landfills' non-hazardous waste.
PROCEDURE FOR THE ACCEPTANCE OF WASTE AT LANDFILLS
1.1. Basic characterisation
Basic characterisation is the first step in the acceptance procedure and constitutes a full characterisation of the waste by gathering all the necessary information for a safe disposal of the waste in the long term. Basic characterisation is required for each type of waste.
1.1.1. Functions of basic characterisation
Basic information on the waste (type and origin, composition, consistency, leachability and - where necessary and available - other characteristic properties)
Basic information for understanding the behaviour of waste in landfills and options for treatment as laid out in Article 6(a) of the Landfill Directive
Assessing waste against limit values
Detection of key variables (critical parameters) for compliance testing and options for simplification of compliance testing (leading to a significant decrease of constituents to be measured, but only after demonstration of relevant information). Characterisation may deliver ratios between basic characterisation and results of simplified test procedures as well as frequency for compliance testing.
If the basic characterisation of waste shows that the waste fulfils the criteria for a landfill class as laid down in section 2 of this Annex, the waste is deemed to be acceptable at this landfill class. If this is not the case, the waste is not acceptable at this landfill class.
The producer of the waste or, in default, the person responsible for its management, is responsible for ensuring that the characterisation information is correct.
The operator shall keep records of the required information for a period to be defined by the Member State.
1.1.2. Fundamental requirements for basic characterisation of the waste
Source and origin of the waste
Information on the process producing the waste (description and characteristics of raw materials and products)
Description of the waste treatment applied in compliance with Article 6(a) of the Landfill Directive, or a statement of reasons why such treatment is not considered necessary
Data on the composition of the waste and the leaching behaviour, where relevant
Appearance of the waste (smell, colour, physical form)
Code according to the European waste list (Commission Decision 2001/118/EC)(1)
For hazardous waste in case of mirror entries: the relevant hazard properties according to Annex III to Council Directive 91/689/EEC of 12 December 1991 on hazardous waste(2)
Information to prove that the waste does not fall under the exclusions of Article 5(3) of the Landfill Directive
The landfill class at which the waste may be accepted
If necessary, additional precautions to be taken at the landfill
Check if the waste can be recycled or recovered.
1.1.3. Testing
As a general rule waste must be tested to obtain the above information. In addition to the leaching behaviour, the composition of the waste must be known or determined by testing. The tests used for basic characterisation must always include those to be used for compliance testing.
The content of the characterisation, the extent of laboratory testing required and the relationship between basic characterisation and compliance checking depends on the type of waste. A differentiation can be made between:
wastes that are regularly generated in the same process;
wastes that are not regularly generated.
The characterisations outlined in points (a) and (b) will provide information that can be directly compared with acceptance criteria for the relevant class of landfill and, in addition, descriptive information can be supplied (e.g. the consequences of depositing with municipal waste).
Wastes regularly generated in the same process
These are individual and consistent wastes regularly generated in the same process, where:
the installation and the process generating the waste are well known and the input materials to the process and the process itself are well defined,
the operator of the installation provides all necessary information and informs the operator of the landfill of changes to the process (especially changes to the input material).
The process will often be at a single installation. The waste can also be from different installations, if it can be identified as single stream with common characteristics within known boundaries (e.g. bottom ash from the incineration of municipal waste).
For these wastes the basic characterisation will comprise the fundamental requirements listed in section 1.1.2 and especially the following:
compositional range for the individual wastes,
range and variability of characteristic properties,
if required, the leachability of the wastes determined by a batch leaching test and/or a percolation test and/or a pH dependence test,
key variables to be tested on a regular basis.
If the waste is produced in the same process in different installations, information must be given on the scope of the evaluation. Consequently, a sufficient number of measurements must be taken to show the range and variability of the characteristic properties of the waste. The waste can then be considered characterised and shall subsequently be subject to compliance testing only, unless significant change in the generation processes occur.
For wastes from the same process in the same installation, the results of the measurements may show only minor variations of the properties of the waste in comparison with the appropriate limit values. The waste can then be considered characterised, and shall subsequently be subject to compliance testing only, unless significant changes in the generation process occur.
Waste from facilities for the bulking or mixing of waste, from waste transfer stations or mixed waste streams from waste collectors, can vary considerably in their properties. This must be taken into consideration in the basic characterisation. Such wastes may fall under case (b).
Wastes that are not regularly generated
These wastes are not regularly generated in the same process in the same installation and are not part of a well-characterised waste stream. Each batch produced of such waste will need to be characterised. The basic characterisation shall include the fundamental requirements for basic characterisation. As each batch produced has to be characterised, no compliance testing is needed.
1.1.4. Cases where testing is not required
Testing for basic characterisation can be dispensed with in the following cases:
the waste is on a list of wastes not requiring testing as laid down in section 2 of this Annex;
all the necessary information, for the basic characterisation, is known and duly justified to the full satisfaction of the competent authority;
certain waste types where testing is impractical or where appropriate testing procedures and acceptance criteria are unavailable. This must be justified and documented, including the reasons why the waste is deemed acceptable at this landfill class.
1.2. Compliance testing
When waste has been deemed acceptable for a landfill class on the basis of a basic characterisation pursuant to section 1, it shall subsequently be subject to compliance testing to determine if it complies with the results of the basic characterisation and the relevant acceptance criteria as laid down in section 2.
The function of compliance testing is periodically to check regularly arising waste streams.
The relevant parameters to be tested are determined in the basic characterisation. Parameters should be related to basic characterisation information; only a check on critical parameters (key variables), as determined in the basic characterisation, is necessary. The check has to show that the waste meets the limit values for the critical parameters.
The tests used for compliance testing shall be one or more of those used in the basic characterisation. The testing shall consist at least of a batch leaching test. For this purpose the methods listed under section 3 shall be used.
Wastes that are exempted from the testing requirements for basic characterisation in section 1.1.4(a) and section 1.1.4(c) are also exempted from compliance testing. They will, however, need checking for compliance with basic characterisation information other than testing.
Compliance testing shall be carried out at least once a year and the operator must, in any event, ensure that compliance testing is carried out in the scope and frequency determined by basic characterisation.
Records of the test results shall be kept for a period that will be determined by the Member State.
1.3. On-site verification
Each load of waste delivered to a landfill shall be visually inspected before and after unloading. The required documentation shall be checked.
For waste deposited by the waste producer at a landfill in his control, this verification may be made at the point of dispatch.
The waste may be accepted at the landfill, if it is the same as that which has been subjected to basic characterisation and compliance testing and which is described in the accompanying documents. If this is not the case, the waste must not be accepted.
Member States shall determine the testing requirements for on-site verification, including where appropriate rapid test methods.
Upon delivery, samples shall be taken periodically. The samples taken shall be kept after acceptance of the waste for a period that will be determined by the Member State (not less than one month; see Article 11(b) of the Landfill Directive.
WASTE ACCEPTANCE CRITERIA
This section sets out the criteria for the acceptance of waste at each landfill class, including criteria for underground storage.
In certain circumstances, up to three times higher limit values for specific parameters listed in this section (other than dissolved organic carbon (DOC) in sections 2.1.2.1, 2.2.2, 2.3.1 and 2.4.1, BTEX, PCBs and mineral oil in section 2.1.2.2, total organic carbon (TOC) and pH in section 2.3.2 and loss on ignition (LOI) and/or TOC in section 2.4.2, and restricting the possible increase of the limit value for TOC in section 2.1.2.2 to only two times the limit value) are acceptable, if
the competent authority gives a permit for specified wastes on a case-by-case basis for the recipient landfill, taking into account the characteristics of the landfill and its surroundings, and
emissions (including leachate) from the landfill, taking into account the limits for those specific parameters in this section, will present no additional risk to the environment according to a risk assessment.
Member States shall report to the Commission on the annual number of permits issued under this provision. The reports shall be sent to the Commission at intervals of three years as part of the reporting on the implementation of the Landfill Directive in accordance with the specifications laid down in Article 15 thereof.
Member States shall define criteria for compliance with the limit values set out in this section.
2.1. Criteria for landfills for inert waste
2.1.1. List of wastes acceptable at landfills for inert waste without testing
Wastes on the following short list are assumed to fulfil the criteria as set out in the definition of inert waste in Article 2(e) of the Landfill Directive and the criteria listed in section 2.1.2. The wastes can be admitted without testing at a landfill for inert waste.
The waste must be a single stream (only one source) of a single waste type. Different wastes contained in the list may be accepted together, provided they are from the same source.
In case of suspicion of contamination (either from visual inspection or from knowledge of the origin of the waste) testing should be applied or the waste refused. If the listed wastes are contaminated or contain other material or substances such as metals, asbestos, plastics, chemicals, etc. to an extent which increases the risk associated with the waste sufficiently to justify their disposal in other classes of landfills, they may not be accepted in a landfill for inert waste.
If there is a doubt that the waste fulfils the definition of inert waste according to Article 2(e) of the Landfill Directive and the criteria listed in section 2.1.2 or about the lack of contamination of the waste, testing must be applied. For this purpose the methods listed under section 3 shall be used.
>TABLE>
Waste not appearing on this list must be subject to testing as laid down under section 1 to determine if it fulfils the criteria for waste acceptable at landfills for inert waste as set out in section 2.1.2.
2.1.2. Limit values for waste acceptable at landfills for inert waste
2.1.2.1. Leaching limit values
The following leaching limit values apply for waste acceptable at landfills for inert waste, calculated at liquid to solid ratios (L/S) of 2 l/kg and 10 l/kg for total release and directly expressed in mg/l for C0 (the first eluate of percolation test at L/S = 0,1 l/kg). Member States shall determine which of the test methods (see section 3) and corresponding limit values in the table should be used.
>TABLE>
2.1.2.2. Limit values for total content of organic parameters
In addition to the leaching limit values under section 2.1.2.1, inert wastes must meet the following additional limit values:
>TABLE>
2.2. Criteria for landfills for non-hazardous waste
Member States may create subcategories of landfills for non-hazardous waste.
In this Annex limit values are laid down only for non-hazardous waste, which is landfilled in the same cell with stable, non-reactive hazardous waste.
2.2.1. Wastes acceptable at landfills for non-hazardous waste without testing
Municipal waste as defined in Article 2(b) of the Landfill Directive that is classified as non-hazardous in Chapter 20 of the European waste list, separately collected non-hazardous fractions of household wastes and the same non-hazardous materials from other origins can be admitted without testing at landfills for non-hazardous waste.
The wastes may not be admitted if they have not been subjected to prior treatment according to Article 6(a) of the Landfill Directive, or if they are contaminated to an extent which increases the risk associated with the waste sufficiently to justify their disposal in other facilities.
They may not be accepted in cells, where stable, non-reactive hazardous waste is accepted pursuant to Article 6(c)(iii) of the Landfill Directive.
2.2.2. Limit values for non-hazardous waste
The following limit values apply to granular non-hazardous waste accepted in the same cell as stable, non-reactive hazardous waste, calculated at L/S = 2 and 10 l/kg for total release and directly expressed in mg/l for C0 (in the first eluate of percolation test at L/S = 0,1 l/kg). Granular wastes include all wastes that are not monolithic. Member States shall determine which of the test methods (see section 3) and corresponding limit values in the table should be used.
>TABLE>
Member States shall set criteria for monolithic waste to provide the same level of environmental protection given by the above limit values.
2.2.3. Gypsum waste
Non-hazardous gypsum-based materials should be disposed of only in landfills for non-hazardous waste in cells where no biodegradable waste is accepted. The limit values for TOC and DOC given in sections 2.3.2 and 2.3.1 shall apply to wastes landfilled together with gypsum-based materials.
2.3. Criteria for hazardous waste acceptable at landfills for non-hazardous waste pursuant to Article 6(c)(iii)
Stable, non-reactive means that the leaching behaviour of the waste will not change adversely in the long-term, under landfill design conditions or foreseeable accidents:
in the waste alone (for example, by biodegradation),
under the impact of long-term ambient conditions (for example, water, air, temperature, mechanical constraints),
by the impact of other wastes (including waste products such as leachate and gas).
2.3.1. Leaching limit values
The following leaching limit values apply to granular hazardous waste acceptable at landfills for non-hazardous waste, calculated at L/S = 2 and 10 l/kg for total release and directly expressed in mg/l for C0 ( the first eluate of percolation test at L/S = 0,1 l/kg). Granular wastes include all wastes that are not monolithic. Member States shall determine which of the test methods and corresponding limit values should be used.
>TABLE>
Member States shall set criteria for monolithic waste to provide the same level of environmental protection given by the above limit values.
2.3.2. Other criteria
In addition to the leaching limit values under section 2.3.1, granular wastes must meet the following additional criteria:
>TABLE>
Member States must set criteria to ensure that the waste will have sufficient physical stability and bearing capacity.
Member States shall set criteria to ensure that hazardous monolithic wastes are stable and non-reactive before acceptance in landfills for non-hazardous waste.
2.3.3. Asbestos waste
Construction materials containing asbestos and other suitable asbestos waste may be landfilled at landfills for non-hazardous waste in accordance with Article 6(c)(iii) of the Landfill Directive without testing.
For landfills receiving construction materials containing asbestos and other suitable asbestos waste the following requirements must be fulfilled:
the waste contains no other hazardous substances than bound asbestos, including fibres bound by a binding agent or packed in plastic,
the landfill accepts only construction material containing asbestos and other suitable asbestos waste. These wastes may also be landfilled in a separate cell of a landfill for non-hazardous waste, if the cell is sufficiently self-contained,
in order to avoid dispersion of fibres, the zone of deposit is covered daily and before each compacting operation with appropriate material and, if the waste is not packed, it is regularly sprinkled,
a final top cover is put on the landfill/cell in order to avoid the dispersion of fibres,
no works are carried out on the landfill/cell that could lead to a release of fibres (e.g. drilling of holes),
after closure a plan is kept of the location of the landfill/cell indicating that asbestos wastes have been deposited,
appropriate measures are taken to limit the possible uses of the land after closure of the landfill in order to avoid human contact with the waste.
For landfills receiving only construction material containing asbestos, the requirements set out in Annex I, point 3.2 and 3.3 of the Landfill Directive can be reduced, if the above requirements are fulfilled.
2.4. Criteria for waste acceptable at landfills for hazardous waste
2.4.1. Leaching limit values
The following leaching limit values apply for granular waste acceptable at landfills for hazardous waste, calculated at L/S = 2 and 10 l/kg for total release and directly expressed in mg/l for C0 (in the first eluate of percolation test at L/S = 0,1 l/kg). Granular wastes include all wastes that are not monolithic. Member States shall determine which of the test methods and corresponding limit values in the table should be used.
>TABLE>
Member States shall set criteria for monolithic waste to provide the same level of environmental protection given by the above limit values.
2.4.2. Other criteria
In addition to the leaching limit values under section 2.4.1, hazardous wastes must meet the following additional criteria:
>TABLE>
2.5. Criteria for underground storage
For the acceptance of waste in underground storage sites, a site-specific safety assessment as defined in Annex A must be carried out. Waste may be accepted only if it is compatible with the site-specific safety assessment.
At underground storage sites for inert waste, only waste that fulfils the criteria set out in section 2.1 may be accepted.
At underground storage sites for non-hazardous waste, only waste that fulfils the criteria set out in section 2.2 or in section 2.3 may be accepted.
At underground storage sites for hazardous waste, waste may be accepted only if it is compatible with the site-specific safety assessment. In this case, the criteria set out in section 2.4 do not apply. However, the waste must be subject to the acceptance procedure as set out in section 1.
SAMPLING AND TEST METHODS
Sampling and testing for basic characterisation and compliance testing shall be carried out by independent and qualified persons and institutions. Laboratories shall have proven experience in waste testing and analysis and an efficient quality assurance system.
Member States may decide that:
the sampling may be carried out by producers of waste or operators under the condition that sufficient supervision of independent and qualified persons or institutions ensures that the objectives set out in this Decision are achieved;
the testing of the waste may be carried out by producers of waste or operators if they have set up an appropriate quality assurance system including periodic independent checking.
As long as a CEN standard is not available as formal EN, Member States will use either national standards or procedures or the draft CEN standard, when it has reached the prEN stage.
The following methods shall be used.
Sampling
For the sampling of waste - for basic characterisation, compliance testing and on-site verification testing - a sampling plan shall be developed according to part 1 of the sampling standard currently developed by CEN.