This TSI concerns the rolling stock subsystem, which is one of the subsystems listed in Annex II(1) to Directive 96/48/EC.
This TSI is part of a set of six TSIs, which cover all the eight subsystems defined in the Directive. The specifications concerning the ‘users’ and ‘environment’ subsystems, which are necessary to ensure interoperability of the trans-European high-speed rail system in compliance with the essential requirements, are set out in the TSIs concerned.
This TSI is applicable to trains running at a speed of at least 250 km/h on the lines specially built for high speed and at a speed of the order of 200 km/h on existing lines which have been or are to be specially upgraded. As far as trains running on upgraded lines at a speed of the order of 200 km/h and on other conventional lines are concerned, Article 2 of the present TSI Decision is applicable as long as this case is not covered in the TSI revision process.
More information about the rolling stock subsystem is given in Chapter 2.
The geographical scope of this TSI is the trans-European high-speed rail system as described in Annex I to Directive 96/48/EC.
Reference shall be made in particular to the lines of the trans-European rail network described in European Parliament and Council Decision No 1692/96/EC of 23 July 1996 on Community guidelines for the development of the trans-European transport network or in any update to the same Decision as a result of the revision provided for in Article 21 of that Decision.
In accordance with Article 5(3) and with Annex I(1)b of Directive 96/48/EC, this TSI:
specifies the essential requirements for the subsystems and their interfaces (Chapter 2);
establishes the basic parameters described in Annex II(3) to that Directive, which are necessary to meet the essential requirements (Chapter 4);
establishes the conditions to be complied with to achieve the specified performances for each of the following categories of line (Chapter 4):
category I: specially built high-speed lines equipped for speeds generally equal to or greater than 250 km/h,
category II: specially upgraded high-speed lines equipped for speeds of the order of 200 km/h,
category III: specially upgraded high-speed lines which have special features as a result of topographical, relief or town-planning constraints, on which the speed must be adapted to each case;
establishes implementing provisions in certain specific cases (Chapter 7);
determines the interoperability constituents and interfaces which must be covered by European Specifications, including European standards, which are needed in order to achieve interoperability within the trans-European high-speed rail system while meeting the essential requirements (Chapter 5);
states, in each case under consideration, which of the modules defined in Decision 93/465/EEC or, where appropriate, which specific procedures are to be used in order to assess either the conformity or the suitability for use of the interoperability constituents, as well as ‘EC’ verification of the subsystems (Chapter 6).
‘The characteristics of the rolling stock must be such as to allow it to travel on any line on which it is expected to operate. (Council Directive 96/48/EC, Annex III, essential requirement 2.4.3)’.
Trains that meet the technical requirements stated in this TSI are able to serve the lines mentioned in Annex I(1)b to Directive 96/48/EC.
The rolling stock subsystem does not include the control-command, operation or power supply subsystems since these subsystems are specified in their own TSIs.
In addition, rolling stock does not include the train staff (driver and other on-board train crew).
The rolling stock shall fulfil the following functions:
carry and protect the passengers and train crew
accelerate, maintain speed, brake and stop
keep the train driver informed, provide a view ahead, and allow proper control
support and guide the train on the track
signal the presence of the train to others
function safely even in the event of incidents
respect the environment.
Trains shall ensure the required level of safety for passengers and train crew during access to and egress from the trains, and during their journey. Trains shall also be sensitive to the special needs of persons of reduced mobility.
The performance defined in the TSI will allow vehicles to fit into the timetable slots on the sections or stretches of the trans-European high-speed network for which the rolling stock is designed.
The driver shall be provided with a clear view of the line ahead. All instruments and controls relating to train operation and the control-command subsystem shall be clearly marked, work in real-time, and be unambiguous for the driver.
The different needs of this subsystem are defined by standards for the wheels that comprise the interface with the rail in the infrastructure subsystem.
The contact geometry is such that the stability of the train with all its equipment in good working order is ensured at the highest operating speed specified for the trainset. This aspect allows the interface with the many parameters within the infrastructure subsystem such as the track gauge, cant deficiency and equivalent conicity, to be defined.
Trains are provided with equipment which enables them to indicate their presence in an audible, visual and/or electronic form acceptable to all parts of the interoperable network and its traffic management systems.
Trains are provided with safety devices to fulfil their functions in the event of possible incidents, reducing the effects of such incidents, and allowing their elimination whenever possible.
The materials selected for use on rolling stock shall minimise the emission of harmful and dangerous fumes or gases during use of the trains. The limits set for exterior noise and electromagnetic interference shall result in minimal environmental impact.
As national railways are equipped with various electrification systems, electric trains shall be able to use the available voltage and frequency, and have the correct pantograph to handle the catenary geometry.
These requirements for traction supply are defined in the energy subsystem TSI.
Pantograph: despite being installed on rolling stock, the pantographs are considered to be a part of the Energy subsystem as an important device the proper current-collection function of which is directly linked to the characteristics of the overhead line. The interface characteristics of the pantographs are specified and described in the energy TSI.
The interfaces and characteristics of the on-board ERTMS signalling equipment and the radio system are entirely specified and described in the control-command TSI.
Major maintenance work that allows the required reliability and availability targets to be met are the responsibility of the railway undertaking that operates the vehicles. The specific technical needs for undertaking tasks appropriate to interoperability in facilities on the interoperable network that do not belong to the rolling stock operator are specified in the maintenance TSI.
3.1.
Under Article 4(1) of Directive 96/48/EC, the trans-European high-speed rail system, subsystems and their interoperability constituents shall meet the essential requirements set out in general terms in Annex III to the Directive.
3.2.
The essential requirements relate to:
safety,
reliability and availability,
health,
environmental protection,
technical compatibility.
According to Directive 96/48/EC, the essential requirements can be generally applied to the whole trans-European high-speed rail system or be specific to particular aspects of each subsystem and its constituents.
3.3.
In the case of the rolling stock subsystem, the specific aspects, in addition to the considerations contained in Annex III to the Directive, are as follows:
‘The design, construction or assembly, maintenance and monitoring of safety-critical components, and more particularly of the components involved in train movements must be such as to guarantee safety at the level corresponding to the aims laid down for the network, including those for specific degraded situations’.
This safety requirement is of universal application; as specified in Chapter 1, Section 1.3, this document is limited to the definition of those conditions relating to interoperability. In this regard, this essential requirement is satisfied when all the basic criteria that define the rolling stock in Chapter 4 of this TSI are met.
‘The parameters involved in the wheel-rail contact must meet the stability requirements needed in order to guarantee safe movement at the maximum authorised speed’.
In order to satisfy this requirement, the wheel profiles, the allowable profile wear and the components affecting running stability shall be specified in Section 4.2.10 in such a way as to be completely compatible with the track criteria defined in the infrastructure subsystem.
Bearing in mind the importance of maintaining these parameters to guarantee safe operation, it is necessary to make arrangements to monitor these parameters on a continuous or periodic basis to prevent their deterioration over time.
‘The components used must withstand any normal or exceptional stresses that have been specified during their period in service. The safety repercussions of any accidental failures must be limited by appropriate means’.
The components concerned in respect of each requirement correspond to the constituents and elements for which the characteristics are given in this TSI, together with their monitoring devices. The main characteristics for this requirement are:
the static resistance of the vehicle structures,
wheel-wear criteria as defined by the choice of material,
the hot-box detection,
the environmental conditions for which the rolling stock equipment is specified,
the windscreen characteristics.
The relevant characteristics to validate in respect of this TSI are defined in Sections 4.1.7, 4.2.10, 4.3.12 and 4.3.19.
In addition, some characteristics are given in order to meet this requirement in the context of their interface with the infrastructure subsystem:
maximum track forces,
heat transmitted to the rail,
effects of crosswinds.
The relevant characteristics to validate in respect of this TSI are defined in Sections 4.1.1, 4.2.15 and 4.2.14.
‘The design of fixed installation and rolling stock and the choice of the materials used must be aimed at limiting the generation, propagation and effects of fire and smoke fumes in the event of a fire.’
This requirement is met by Section 4.3.11 which covers fire protection.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.3.11.
‘Any devices intended to be handled by users must be so designed as not to impair their safety if used foreseeably in a manner not in accordance with the posted instructions.’
The present design of trains already takes these risks into account. There is no need to define any specific characteristics purely for interoperability.
‘The rolling stock structures and those of the links between vehicles must be designed in such a way as to protect the passenger and driving compartments in the event of collision or derailment.’
In order to meet this requirement, the vehicle structures are designed with passive safety provisions. The basic principle envisages the possibility of a collision with an obstacle such as a heavy lorry on a level crossing or a rock fall, where the compartments that contain the passengers and driver are subject to minimal deformation. Collision energy shall be absorbed in unoccupied crumple zones designed for such eventualities, which limit deceleration forces and prevent overriding of the vehicle bodies.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.1.7.
‘The electrical equipment must not impair the safety and functioning of the control and command and signalling installations.’
This requirement is met by the criteria defined in the control command TSI, in the paragraph dealing with the electromagnetic compatibility of the rolling stock and the signalling system.
The constraints to operation over existing infrastructure are dealt with on a case-by-case basis. It is imperative to respect the limits defined for existing installations. To find out the different infrastructure characteristics, refer to the ‘Register of infrastructure’ in which the information is given on a line by line basis.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.1.9.
‘The braking techniques and the stresses exerted must be compatible with the design of the tracks, engineering structures and signalling systems’.
For the present TSI, this requirement is dealt with by two basic parameters.
the braking performances defined in Section 4.1.5,
the maximum longitudinal force, defined in Section 4.1.1c, to be applied to the track without exceeding the maximum acceptable longitudinal force on the infrastructure.
Furthermore, the particular case of brake systems independent of wheel rail adhesion that use electromagnetic effects in the rail (eddy current brakes) rather than wheel/rail adhesion is tackled separately in Section 4.2.15 in order to evaluate the consequences of thermal effects in the rails.
‘Steps must be taken to prevent access to electrically-live constituents in order not to endanger the safety of persons’.
To satisfy this requirement, the rolling stock may also be manufactured using European standards relating to protection against electric shock.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.3.17.
‘In the event of danger, devices must enable passengers to inform the driver and accompanying staff to contact him.’
This requirement concerns the indications given to passengers relating to the passenger alarm signal. The various functions of the public address system and of the intercom between the driver and the train crew are intended to respond to this requirement.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.2.12.
‘The access door must incorporate an opening and closing system which guarantees passenger safety.’
This requirement is dealt with in the functional specification of the door control, and by constraints concerning the possibility of door unlocking.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.2.6.
‘Emergency exits must be provided and indicated.’
The number of emergency exits, their distribution, their operation and their sign posting are defined in the present TSI in order to meet the evacuation requirement.
The relevant characteristics to validate in respect of this TSI are defined in Sections 4.2.7 and 4.2.8.
‘Appropriate provisions must be laid down to take account of the particular safety conditions in very long tunnels.’
The provisions relating to fire and fume protection, the trainset design with a driver's cab at each end, emergency alarms which allow the driver to chose his stopping point, emergency lighting, the public address system and the other items defined in this TSI work together to improve safety in tunnels.
The additional stipulations of this requirement are gathered together in a specific paragraph. They are only envisaged for rolling stock that is regularly used through very long tunnels having specific demands listed in the ‘infrastructure register’.
The relevant characteristics to validate in respect of this TSI are defined in Sections 4.3.14 and 4.2.12.
‘An emergency lighting system having a sufficient intensity and duration is an absolute requirement on board trains.’
This requirement is covered by the definition of the main functions of the emergency lighting system.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.3.15.
‘Trains must be equipped with a public address system which provides a means of communication to the public from on-board staff and ground control.’
This requirement is covered by the definition of the main functions of the public address system.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.3.16.
‘The monitoring and maintenance of fixed or movable components that are involved in train movements must be organised, carried out and quantified in such a manner as to maintain their operation under the intended conditions.’
‘The design of the vital equipment and the running, traction and braking equipment and also the control and command system must, in a specific degraded situation, be such as to enable the train to continue without adverse consequences for the equipment remaining in service.’
Meeting the performances specified in Sections 4.1.5, 4.2.1, 4.2.9, 4.3.1 and 4.3.3 allows these two requirements to be met.
‘Materials likely, by virtue of the way they are used, to constitute a health hazard to those having access to them must not be used in trains and railway infrastructures.’
This requirement, which is not specific to the railway field, is covered by compliance with the appropriate European or national legislation.
‘Those materials must be selected, deployed and used in such a way as to restrict the emission of harmful and dangerous fumes or gases, particularly in the event of fire.’
As already defined in Section 3.3.1, dealing with essential requirement 1.1.4, this requirement is dealt with in Section 4.3.11, which deals with fire protection.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.3.11.
‘The repercussions on the environment of the establishment and operation of the trans-European high-speed rail system must be assessed and taken into account at the design stage of the system in accordance with the Community provisions in force.’
As concerns rolling stock, this requirement is covered by boundary characteristics relating to outside noise, electromagnetic interference as well as light pollution.
The relevant characteristics to validate in respect of this TSI are defined in Sections 4.1.8; 4.1.9; 4.2.20.
‘The materials used in the trains must prevent the emission of fumes or gases which are harmful and dangerous to the environment, particularly in the event of fire.’
This requirement, which is not specific to the railway field, is covered by compliance with the appropriate European or national legislation.
‘The rolling stock and energy-supply systems must be designed and manufactured in such a way as to be electromagnetically compatible with the installations, equipment and public or private networks with which they might interfere.’
This essential requirement is covered by the basic parameter ‘Boundary characteristics linked to outside electromagnetic interference’.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.1.9.
‘The technical characteristics of the infrastructures and fixed installations must be compatible with each other and with those of the trains to be used on the trans-European high-speed rail system.
If adherence to these characteristics proves difficult on certain sections of the network, temporary solutions, which ensure compatibility in the future, may be implemented.’
This general requirement concerns the rolling stock fundamental criteria that correspond to the characteristics defined in Chapter 4 of this TSI.
Some temporary solutions are envisaged. They will be evoked in particular cases to allow proper operation on existing lines or will ultimately appear in the form of special characteristics within the ‘infrastructure register’.
‘The electrical equipment must be compatible with the operation of the control and command and signalling installations.’
Defining the electrical boundary characteristics, the limits of electromagnetic interference and the interface with the control command subsystem ensures this compatibility.
The relevant characteristics to validate in respect of this TSI are defined in Sections 4.1.6, 4.1.9 and 4.2.4.
‘The characteristics of the current-collection devices must be such as to enable trains to travel under the energy supply systems for the trans-European high-speed rail system.’
This compatibility is ensured by the definition of the interface interfaces with the electrification system as specified in the TSI energy subsystem.
The relevant characteristics to validate in respect of this TSI are defined in Section 4.2.3.
‘The characteristics of the rolling stock must be such as to allow it to travel on any line on which it is expected to operate.’
This essential requirement is covered by values of the basic parameters, characteristics of the subsystem interfaces and additionally by the specified rolling stock performance.
The relevant characteristics to validate in respect of this TSI are defined in Sections 4.1, 4.2 and 4.3.
Conformity of the rolling stock subsystem and its constituents to the essential requirements is checked in accordance with the provisions envisaged in Directive 96/48/EC as well as in this TSI.
The Trans-European high-speed rail system (to which Directive 96/48/EC applies and of which the subsystem is a part) is an integrated system. It requires the basic parameters, interfaces and performance to be verified in particular so as to ensure that the system is interoperable and that the essential requirements are met.
With regard to technical interoperability, the rolling stock subsystem has the following characteristics:
basic parameters
interfaces with other subsystems
specified performance
The common characteristics of rolling stock are defined in Section 4 of the present TSI.
The basic parameters for the Rolling Stock subsystem are those listed in Annex II of Directive 96/48/EC:
maximum track forces (BP4)
axle load (BP10)
maximum train length (BP11)
vehicle loading gauge (BP12)
minimum braking characteristics (BP13)
electrical boundary characteristics for rolling stock (BP14)
mechanical boundary characteristics for rolling stock (BP15)
exterior noise limits (BP17)
electromagnetic interference limits (BP19)
interior noise limits (BP20)
air conditioning limits (BP21)
requirements for the transport of mobility impaired people (BP22).
Additional basic parameters:
maximum pressure variations in tunnels (BP23)
maximum gradients (BP25).
In addition to basic parameter BP10 that deals with the static axle load, the characteristics that allow the maximum track forces to be defined are:
the dynamic load applied to the rail by the wheel,
the transverse forces exerted on the track by the train.
Dynamic load
The maximum vertical load to be exerted by the wheels on the rail (dynamic load of wheel Q) is defined as follows: