Appendix
AIRWORTHINESS AND ENVIRONMENTAL CERTIFICATION
EASA, AVIATION AUTHORITY, AND U.S. PRODUCTS, ASSOCIATED EXPORT DOCUMENTATION, AND TECHNICAL ASSISTANCE ACTIVITY ACCEPTED UNDER THIS AGREEMENT
European Community Technical Agent | Products, export documentation, and technical assistance activities
EASA
Products and Associated Export Documentation Accepted for Import into the U.S. |
New aircraft conforming to an FAA-approved design, manufactured under an EASA — issued Production Organisation Approval (POA) (paragraph 3.4.3), and accompanied by an EASA Form 27.
New engines and propellers conforming to an FAA-approved design that are manufactured under an EASA-issued POA accompanied by an EASA Form 1, Authorised Release Certificate.
The following new parts manufactured under an EASA-issued POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Design data (compliance statements) and test witnessing.
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Aviation Authority in Listed EU Member State | Products, export documentation, and technical assistance activities
Austria
Products and Associated Export Documentation Accepted for Import into the U.S. |
New small airplanes, VLA, and sailplanes and powered sailplanes, conforming to an FAA-approved design, manufactured under an Austrian POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or an Austrian Export Certificate of Airworthiness issued before September 28, 2008.
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M, as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or an Austrian Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of Austria, and specified on the Austrian Export Certificate of Airworthiness or EASA Form 27.
New engines and propellers conforming to an FAA-approved design, manufactured under an Austrian POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
New appliances conforming to an FAA-approved design, manufactured under an Austrian POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under an Austrian POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Belgium
Products and Associated Export Documentation Accepted for Import into the U.S. |
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M, as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Belgian Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of Belgium, and specified on the Belgium Export Certificate of Airworthiness or EASA Form 27.
New appliances conforming to an FAA-approved design, manufactured under a Belgian POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
New manned balloons conforming to an FAA-approved design, manufactured under Subpart F of EASA Part 21 or Belgian POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Belgian Export Certificate of Airworthiness issued before September 28, 2008.
The following new parts manufactured under a Belgian POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Czech Republic
Products and Associated Export Documentation Accepted for Import into the U.S. |
New small airplanes, VLA, and sailplanes conforming to an FAA-approved design, manufactured under a Czech Republic POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Czech Export Certificate of Airworthiness issued before September 28, 2008.
New manned balloons conforming to an FAA-approved design, manufactured under a Czech Republic POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Czech Export Certificate of Airworthiness issued before September 28, 2008.
New airships conforming to an FAA-approved design, manufactured under a Czech Republic POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Czech Export Certificate of Airworthiness issued before September 28, 2008.
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M, as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Czech Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of the Czech Republic, and specified on the Czech Export Certificate of Airworthiness or EASA Form 27.
New engines and propellers conforming to an FAA-approved design, manufactured under a Czech Republic POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
New appliances conforming to an FAA-approved design, manufactured under a Czech Republic POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under a Czech Republic POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Denmark
Products and Associated Export Documentation Accepted for Import into the U.S. |
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M, as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Danish Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of Denmark, and specified on the Danish Export Certificate of Airworthiness or EASA Form 27.
New appliances conforming to an FAA-approved design, manufactured under a Danish POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under a Danish POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Finland
Products and Associated Export Documentation Accepted for Import into the U.S. |
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Finnish Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of Finland, and specified on the Finnish Export Certificate of Airworthiness or EASA Form 27.
New appliances conforming to an FAA-approved design, manufactured under a Finnish POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under a Finnish POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
France
Products and Associated Export Documentation Accepted for Import into the U.S. |
New airplanes, helicopters, VLA, and sailplanes, conforming to an FAA-approved design, manufactured under a French POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a French Export Certificate of Airworthiness issued before September 28, 2008.
New manned balloons conforming to an FAA-approved design, manufactured under Subpart F of EASA Part 21 or French POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a French Export Certificate of Airworthiness issued before September 28, 2008.
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M, as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a French Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of France, and specified on the French Export Certificate of Airworthiness or EASA Form 27.
New engines and propellers conforming to an FAA-approved design, manufactured under a French POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
New appliances conforming to an FAA-approved design, manufactured under a French POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under a French POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Acceptance of French Documentation on Parts Produced in France under a U.S. Production Approval |
EASA Form 1, Authorised Release Certificate, shall be accepted on parts produced under the quality system of a U.S. Production Approval Holder (PAH), at a PAH’s supplier located in France, when that supplier also holds a French POA for the same part.
Germany
Products and Associated Export Documentation Accepted for Import into the U.S. |
New airplanes, helicopters, VLA, sailplanes and motorised sailplanes, conforming to an FAA-approved design, manufactured under a German POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a German Export Certificate of Airworthiness issued before September 28, 2008.
New manned balloons conforming to an FAA-approved design, manufactured under a German POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a German Export Certificate of Airworthiness issued before September 28, 2008.
New airships conforming to an FAA-approved design, manufactured under a German POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a German Export Certificate of Airworthiness issued before September 28, 2008.
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M, as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a German Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of Germany, and specified on the German Export Certificate of Airworthiness or EASA Form 27.
New engines and propellers conforming to an FAA-approved design, manufactured under a German POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
New appliances conforming to an FAA-approved design, manufactured under a German POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under a German POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Acceptance of German Documentation on Parts Produced in Germany under a U.S. Production Approval |
EASA Form 1, Authorised Release Certificate, shall be accepted on parts produced under the quality system of a U.S. Production Approval Holder (PAH), at a PAH’s supplier located in Germany, when that supplier also holds a German POA for the same part.
Italy
Products and Associated Export Documentation Accepted for Import into the U.S. |
New airplanes, helicopters, and VLA, conforming to an FAA-approved design, manufactured under an Italian POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or an Italian Export Certificate of Airworthiness issued before September 28, 2008.
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145 or Part M, as applicable, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or an Italian Export Certificate of Airworthiness issued before September 28, 2008. If relevant provisions of Part M are not yet implemented, the applicable maintenance requirements will be those of Italy, and specified on the Italian Export Certificate of Airworthiness or EASA Form 27.
New appliances conforming to an FAA-approved design, manufactured under an Italian POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under an Italian POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts regardless of the State of Design for the product and/or appliance;
Modification parts for design changes where EASA acts as the State of Design for the design change for an EU applicant. When these modification parts are associated with an EASA STC, the STC must be within the scope of the technical implementation procedures;
Modification parts for any product where the U.S. is the State of Design for the design change and the parts are produced under licensing agreement to the U.S. design approval holder (split State of Design and State of Manufacture).
Technical Assistance Activities Performed on Behalf of FAA |
Production surveillance and oversight conducted as technical assistance.
Conformity inspection.
Acceptance of Italian Documentation on Parts Produced in Italy under a U.S. Production Approval |
EASA Form 1, Authorised Release Certificate, shall be accepted on parts produced under the quality system of a U.S. Production Approval Holder (PAH), at a PAH’s supplier located in Italy, when that supplier also holds a Italian POA for the same part.
Lithuania
Products and Associated Export Documentation Accepted for Import into the U.S. |
New sailplanes and powered sailplanes conforming to an FAA-approved design manufactured under a Lithuanian POA, and accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Lithuanian Export Certificate of Airworthiness issued before September 28, 2008.
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145, or Part M when implemented, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Lithuanian Export Certificate of Airworthiness issued before September 28, 2008.
New propellers conforming to an FAA-approved design, manufactured under a Lithuanian POA, and accompanied by an EASA Form 1, Authorised Release Certificate, or a JAA Form One issued before September 28, 2005.
The following new parts manufactured under a Lithuanian POA that conform to FAA-approved design data and are eligible for installation in a product which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):
Replacement parts for the products listed above.
Luxembourg
Products and Associated Export Documentation Accepted for Import into the U.S. |
Used aircraft conforming to an FAA-approved design, maintained in accordance with EASA Part 145, or Part M when implemented, when accompanied by an EASA Form 27, Export Certificate of Airworthiness, or a Luxembourgian Export Certificate of Airworthiness issued before September 28, 2008.
The following new parts manufactured under a Luxembourgian POA that conform to FAA-approved design data and are eligible for installation in a product or appliance which has been granted an FAA design approval (accompanied by an EASA Form 1, or a JAA Form One issued before September 28, 2005):